• Journal of the Korean Geotechnical Society
• /
• v.36 no.12
• /
• pp.117-124
• /
• 2020

The present research focuses on a methodology to describe shearing response of clay with respect to temperature. An increase of temperature shifts the normal consolidation line to move down in the plane of void ratio and mean effective stress. The critical state line, however, does not move as much as the normal consolidation line in accordance with temperature increase. As temperature increase, therefore, the difference between the critical state mean effective stress and the pre-consolidation pressure reduces. To reflect this easily, the present study applies a bounding surface consisting of two parts divided by the critical state mean effective stress. This study calibrated a bounding surface for the soft Bangkok clay and performed elemental simulation for undrained triaxial compression tests. The elemental simulation showed that the model can describe the mechanical response upon temperature of clay without complex hardening and evolution rules compared to the experimental data.

• Journal of the Korean Geotechnical Society
• /
• v.23 no.9
• /
• pp.17-28
• /
• 2007

Urban tunnels are usually important in terms of prediction and control of surface settlement, gradient and ground displacement. This paper has studied the application of strain softening analysis to predict deformation behavior of an urban NATM tunnel. The applied strain softening model considered the reduction of shear stiffness and strength parameter after yielding with strain softening effects of a given material. Measurements of surface subsidence and ground displacement were adopted to monitor the ground behavior resulting from the tunneling and to modify tunnel design. The numerical analysis results produced a strain distribution, deformational mechanism and surface settlement profile, which are in good agreement with the results of case study. The approach of strain softening modeling is expected to be a good prediction method on the ground displacement associated with NATM tunneling at shallow depth and soft ground.

• Korean Journal of Radiology
• /
• v.22 no.5
• /
• pp.782-791
• /
• 2021

Objective: To evaluate the signal intensity of the periosteum using ultrashort echo time pulse sequence with three-dimensional cone trajectory (3D UTE) with or without fat suppression (FS) to distinguish from artifacts in porcine tibias. Materials and Methods: The periosteum and overlying soft tissue of three porcine lower legs were partially peeled away from the tibial cortex. Another porcine tibia was prepared as three segments: with an intact periosteum outer and inner layer, with an intact periosteum inner layer, and without periosteum. Axial T1 weighted sequence (T1 WI) and 3D UTE (FS) were performed. Another porcine tibia without periosteum was prepared and subjected to 3D UTE (FS) and T1 WI twice, with positional changes. Two radiologists analyzed images to reach a consensus. Results: The three periosteal tissues that were partially peeled away from the cortex showed a high signal in 3D UTE (FS) and low signal on T1 WI. 3D UTE (FS) showed a high signal around the cortical surface with an intact outer and inner periosteum, and subtle high signals, mainly around the upper cortical surfaces with the inner layer of the periosteum and without periosteum. T1 WI showed no signal around the cortical surfaces, regardless of the periosteum state. The porcine tibia without periosteum showed changes in the high signal area around the cortical surface as the position changed in 3D UTE (FS). No signal was detected around the cortical surface in T1 WI, regardless of the position change. Conclusion: The periosteum showed a high signal in 3D UTE and 3D UTE FS that overlapped with artifacts around the cortical bone.

• Fashion & Textile Research Journal
• /
• v.24 no.6
• /
• pp.667-685
• /
• 2022

This paper aims to investigate 4D printing materials for soft robots. 4D printing is a targeted evolution of the 3D printed structure in shape, property, and functionality. It is capable of self-assembly, multi-functionality, and self-repair. In addition, it is time-dependent, printer-independent, and predictable. The shape-shifting behaviors considered in 4D printing include folding, bending, twisting, linear or nonlinear expansion/contraction, surface curling, and generating surface topographical features. The shapes can shift from 1D to 1D, 1D to 2D, 2D to 2D, 1D to 3D, 2D to 3D, and 3D to 3D. In the 4D printing auxetic structure, the kinetiX is a cellular-based material design composed of rigid plates and elastic hinges. In pneumatic auxetics based on the kirigami structure, an inverse optimization method for designing and fabricating morphs three-dimensional shapes out of patterns laid out flat. When 4D printing material is molded into a deformable 3D structure, it can be applied to the exoskeleton material of soft robots such as upper and lower limbs, fingers, hands, toes, and feet. Research on 4D printing materials for soft robots is essential in developing smart clothing for healthcare in the textile and fashion industry.

• Food Science and Preservation
• /
• v.24 no.7
• /
• pp.957-964
• /
• 2017

The purpose of this study was to determine the optimum spray drying conditions of soft persimmon latte using response surface methodology that is a statistical procedure used for optimization studies. A central composite design was applied to investigate the effects of independent variables, inlet temperature ($X_1$), air flow rate ($X_2$), and feed flow rate ($X_3$), on responses such as yield, water absorption index, and total phenolic compounds. Statistical analysis revealed that independent variables significantly affected all the responses. A maximum yield of 8.11 g was obtained at $90^{\circ}C$ of $X_1$, 51.82 mL/min of $X_2$ and 7.00 mL/min of $X_3$. A minimum water absorption index of 0.58 was obtained at $101^{\circ}C$ of $X_1$, 60.00 mL/min of $X_2$ and 17.00 mL/min of $X_3$. A maximum total phenolic compounds of $298.02{\mu}g/mL$ was obtained at $90^{\circ}C$ of $X_1$, 43.33 mL/min of $X_2$ and 17.00 mL/min of $X_3$. In conclusion, the best spray drying conditions were as follows: $X_1$, $90^{\circ}C$; $X_2$, 53 mL/min; $X_3$, 17 mL/min. Under those optimal conditions, the powder's yield (7.46 g), water absorption index (0.54), and the content of total phenolic compounds ($294.75{\mu}g/mL$) were estimated.

• Journal of the Korean Geosynthetics Society
• /
• v.7 no.3
• /
• pp.41-49
• /
• 2008

This study was carried out the model experiment in laboratory to evaluate the bearing capacity improvement of soft ground as altered constraint condition of reinforcements according to geotextile, georid, steel bar. As a results, the value of BCR was increased linearly as improvement of the stiffness of reinforcements, and the factor governed the increasement of BCR was the increasement of frictions between reinforcement and clay as far as the constrain conditions increased until T=85.6kg. Moreover, An angle of inclination, ${\theta}$, between reinforcement and horizontal surface was distributed from $38^{\circ}$ to $50^{\circ}$ for Geotextile, from $45^{\circ}$ to $50^{\circ}$ for Geogrid and from $14^{\circ}$ to $16^{\circ}$ for steel bar. A radius of heaving, r, of clay ground by vertical weight at side was distributed from 0.6m to 0.7m for Geotextile, from 0.5m to 0.8m for Geogrid, and from 2.4m to 3.0m for steel bar. In case of steel bar, r was 4 times that of Geotextile.

• Korean Journal of Agricultural Science
• /
• v.40 no.4
• /
• pp.325-331
• /
• 2013

This experiment has been carried out to determine optimal culture conditions for the production of cut flowers and tubers of Calla (Zantedeschia 'Golden Affair' and 'Black Magic') in highlands. Treatments consisted of various levels of root zone environments, Results are as follows: Calla 'Golden Affair' were grown with different mulching materials such as Non-mulching, Black film, reflective film, Rice hull. Mulching materials resulted in no difference in the number of cut flowers but flower length was highest in reflective film. Calla 'Black Magic' were treated with various soil water content, soil type and watering time. Number of cut flowers and flower quality were greatest when the plants were watered at -80 kPa soil water content. No symptoms of soft rot (Erwinia carotovora) was observed at this soil water content. The occurrence of soft rot was observed with similar percentage according to soil type and the soil water content. When Calla 'Black Magic' were watered at the time of soil surface drying, growth was greater compared to others. Air temperature and PPF affected plant growth and photosynthesis. Photosynthetic rate was greatest at $25^{\circ}C$ and PPF $200{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$, while lowest at $28^{\circ}C$ and PPF $800{\mu}mol{\cdot}m^{-2}{\cdot}s^{-1}$. Soft rot did not occur without regard to dipping treatment (0, 5, 10, 24, 48 hours) when the day and night temperature were maintained at $25^{\circ}C$ and $20^{\circ}C$, respectively.

• Maxillofacial Plastic and Reconstructive Surgery
• /
• v.34 no.1
• /
• pp.12-16
• /
• 2012

Purpose: The purpose of this study is to evaluate the effect of exposure of hydroxyapatite coating on the amount of bone formation and stability in the dogs. Methods: In this study, hydroxyapatite coated implants (HAPTITE) was placed over the femur bone surface of four dogs about 1 mm. The experimental group was divided into 4 weeks group of 8 implants and 8 weeks group of 8 implants, and then they were sacrificed. The stability of implants was evaluated twice with Osstell$^{TM}$ mentor (Osstell AB, Goteborg, Sweden) at right after placement and sacrifice. The amount of bone formation was evaluated through histomorphometric examination. Results: The stability of implants was in normal range, and tended to increase as time goes by. Mean percentages of new bone formation rates were $90.5{\pm}6.6$ at uppermost 1 mm bone level adjacent to soft tissues (level 1) and $92.9{\pm}4.1$ at next 1 mm bone level (level 2) in 4 weeks group, $90.1{\pm}11.5$ at level 1 and $95.9{\pm}2.3$ at level 2 in 8 weeks group. Mean percentages of bone-implant contact rates were $85.1{\pm}10.8$ at level 1 and $88.1{\pm}13.8$ at level 2 in 4 weeks group, $88.5{\pm}14.4$ at level 1 and $95.3{\pm}3.1$ at level 2 in 8 weeks group. There was no statistically significant difference of new bone formation rate and bone-implant contact rate between uppermost 1 mm bone level adjacent to soft tissues and next 1 mm bone level. However, there was no significant difference in bone formation between 4 and 8 weeks groups. Conclusion: These results suggested that exposed hydroxyapatite coated implants to soft tissue showed favorable bone formation and implant stability.

• Korean Journal of Fisheries and Aquatic Sciences
• /
• v.12 no.4
• /
• pp.297-303
• /
• 1979

Early morphological changes of Omobranchus slogans (STEINDACHNER) (Family Blennidae) were studied based on the samples of 125 individuals collected from Changseon channel of Nam-hae in June 1973 and May 1979. Descriptions were made with particular emphasis on developmental changes of supraorbital region, fin rays, development of chromatophores and the preopercular spine. In the early stages the lateral profile of the supraorbital region is perpendicular to tile sagittal plane, however, in the later stages it becomes curved. In the early stage of 5.55 mm in total length the number of soft rays of dorsal fin is 18, and that of the anal fin 15. Ventral fin first appears as a premoidal proturberance. It fully developes into a fin composed of two soft rays in the stages of 12.9 mm in total length. The caudal fin rays first appear in the ventral part and in the stages of 6.15 mm in total length it gets one or two soft rays which bear 1-2 segments. In the later stages each ray bears more than 5 segments. Melanophores first appear as two black spots on the central part of the head. They are distributed on the opercle and the antero-dorsal surface of the trunk in the stage of 18mm in total length. At this stage the general chromatophore. pattern is identical to the adult stage. The anal fin bears melanophores at the basal part of the rays, and it is one of the remarkable morphological characters of this species. In early stages the preopercular spine develops reaching the basal part of the pectoral fin. In the later stages of 15 mm in total length relative length of the spine decreases to total length, and ie reaches only the distal margin of the opercular.

• Archives of Reconstructive Microsurgery
• /
• v.11 no.2
• /
• pp.153-161
• /
• 2002

Purpose : Plantar surfaces, calcaneal area, and region of Achilles insertion, which are extremely related with weight-bearing area and shoes application, must be reconstructed with glabrous and strong fibrous skin. Numerous methods of reconstructing defects of these regions have been advocated, but the transfer of similar local tissue as a cutaneous flap with preservation of sensory potential would best serve the functional needs of the weight-bearing and non-weight-bearing surfaces of this region. Therefore it is recommended to use the limited skin of medial surface of foot that is similar to plantar region and non-weight-bearing area. In this paper we performed the medial plantar flap transfered as a fasciocutaneous island as one alterative for moderate-sized defects of the plantar forefoot, plantar heel, and area around the ankle in 25 cases and report the result, availability and problem of medial plantar flap. Materials and methods : We performed proximally based medial plantar flap in 22 cases and reverse flow island flap in 3 cases. Average age was $36.5(4{\sim}70)$ years and female was 3 cases. The causes of soft tissue defect were crushing injury on foot 4 cases, small bony exposure at lower leg 1 case, posterior heel defect with exposure of calcaneus 8 cases, severe sore at heel 2 cases, skin necrosis after trauma on posterior foot 4 cases, and defect on insertion area of Achilles tendon 6cases. Average follow up duration was 1.8(7 months-9.5 years) years. Results: Medial plantar flaps was successful in 22 patients. 18 patients preserved cutaneous branches of medial plantar nerve had sensation on transfered flap but diminished sensation or dysesthesia. At the follow up, we found there were no skin ulceration, recurrence of defect or skin breakdown in all 18 patients. But there was one case which occurred skin ulceration postoperatively among another 4 cases not contained medial plantar nerve. At the last follow up, all patients complained diminished sensation and paresthesia at medial plantar area distally to donor site, expecially with 4 patients having severe pain and discomfort during long-time walking. Conclusion : Medial plantar island flap based on medial plantar neurovascualr pedicle have low failure rate with strong fibrous skin and preserve sensibility of flap, so that it is useful method to reconstruct the skin and soft tissue defect of foot. But it should be emphasized that there are some complications such like pain and paresthesia by neuropraxia or injury of medial plantar nerve at more distal area than donor site. We may consider that medial plantar flap have limited flap size and small arc of rotation, and require skin graft closure of the donor defect and must chose this flap deliberately.