• Transactions on Electrical and Electronic Materials
• /
• v.15 no.2
• /
• pp.81-86
• /
• 2014

The process parameter in optimized KOH alkali activation of soft carbon series coke material in high purity was set with DOE experiments design. The activated carbon was produced by performing the activation process based on the set process parameters. The specific surface area was measured and pore size was analyzed by $N_2$ absorption method for the produced activated carbon. The surface functional group was analyzed by Boehm method and metal impurities were analyzed by XRF method. The specific surface area was increased over 2,000 $m^2/g$ as the mixing ratio of activation agent increased. The micro pores in $5{\sim}15{\AA}$ and surface functional group under 0.4 meq/g were obtained. The contents of the metal impurity in activated carbon which is the factor for reducing the electrochemical characteristics was reduced less than 100 ppm through the cleansing process optimization. The electrochemical characteristics of activated carbon in 38.5 F/g and 26.6 F/cc were checked through the impedance measuring with cyclic voltammetry scan rate in 50~300 mV/s and frequency in 10 mHz ~100 kHz. The activated carbon was made in the optimized activation process conditions of activation time in 40 minutes, mixing ratio of activation agent in 4.5 : 1.0 and heat treatment temperature over $650^{\circ}C$.

• 제어로봇시스템학회:학술대회논문집
• /
• 2001.10a
• /
• pp.29.2-29
• /
• 2001

For the design of human-centered systems in which a human and machine such as a robot form a human-in system, human-friendly interaction/interface is essential. Human-friendly interaction is possible when the system is capable of recognizing human biosigns such as5 EMG Signal, hand gesture and facial expressions so the some humanintention and/or emotion can be inferred and is used as a proper feedback signal. In the talk, we report our experiences of applying the Soft computing techniques including Fuzzy, ANN, GA and rho rough set theory for efficiently recognizing various biosigns and for effective inference. More specifically, we first observe characteristics of various forms of biosigns and propose a new way of extracting feature set for such signals. Then we show a standardized procedure of getting an inferred intention or emotion from the signals. Finally, we present examples of application for our model of rehabilitation robot named.

• Proceedings of the IEEK Conference
• /
• 1999.11a
• /
• pp.1045-1048
• /
• 1999

In this paper, we report on a set of new algorithms to realize a nonlinear compressed-domain video/audio editor that overcomes various realization problems. For efficiency, the underlying algorithm, which uses a central data structure in the form of doubled linked lists, performs soft edits of cut and paste (which, in turn, involves soft implementations of frame type conversion) and addresses problems relating to video/audio synchronization and random access, and decoder buffer control.

• Journal of the Korean Association of Oral and Maxillofacial Surgeons
• /
• v.36 no.1
• /
• pp.28-38
• /
• 2010

The factors influencing the relapse and recurrence of skeletal deformity after the orthognathic surgery include various factors such as condylar deviation, the amount of mandibular set-back, stretching force by the soft tissues and muscles around the facial skeleton. The purpose of this report is to recognize and analyze the possible factors of reoperation after orthognathic surgery, due to early relapses. Six patients underwent reoperation after the orthognathic surgeries out of 110 patients from 2006 to 2009 were included in this study. In most cases, clincal signs of the insufficient occlusal stability, anterior open bite, and unilateral shifting of the mandible were founded within 2 weeks postoperatively. Although elastic traction was initiated in every case, inadequate correction made reoperation for these cases inevitable. The chief complaints of five cases were the protruded mandible combined with some degree of asymmetric face and in the other one case, it was asymmetric face only. Various factors were considered as a major cause of post-operative instability such as condylar sagging, counter-clockwise rotation of the mandibular segment, soft tissue tension related with asymmetrical mandibular set-back, preoperatively existing temporomandibular disorder (TMD), poor fabrication of the final wafer, and dual bite tendency of the patients.

• Transactions of Materials Processing
• /
• v.16 no.7
• /
• pp.530-537
• /
• 2007

This paper is concerned with the analysis of plastic deformation of bimetal co-extrusion process. Two sets of material combination have been adopted for analysis, i.e. combinations of Cu/Al and Fe/Al. In the first set of material combination, the selected materials are AA 1100 aluminum alloy as hard material and CDA 110 as soft one. This type of material selection is to examine the effect of hard core and soft sleeve and vice versa on the deformation pattern in terms of plastic zone and velocity discontinuity along the contact surface between construction materials. Four different cases of co-extrusion process in terms of material combination and interference bonding were simulated to investigate the effect of material arrangement between core and sleeve, and of bonding on the plastic zones and velocity discontinuity. In the other set of material combination, model materials used as core and sleeve were AA 1100 and AISI 1010, which are relatively soft and hard, respectively. Process parameters except diameter ratio of core to sleeve material such as semi-die angle, reduction in area in global sense and die comer radius have been set constant throughout the simulation to concentrate our effort on the analysis of influence of diameter ratio on deformation behavior such as deformation zone, surface expansion, exit velocity discontinuity between composite materials, and extrusion forces.

• KIPS Transactions on Computer and Communication Systems
• /
• v.2 no.3
• /
• pp.111-116
• /
• 2013

With technology scaling, soft error rate has greatly increased in embedded systems. Due to high performance and low power consumption, VLIW (Very Long Instruction Word) architectures have been widely used in embedded systems and thus many researches have been studied to improve the reliability of a system by duplicating instructions in VLIW architectures. However, existing studies have ignored the feature, called VLES (Variable Length Execution Set), which is adopted in most modern VLIW architectures to reduce code size. In this paper, we propose how to support instruction duplication in VLIW architecture with VLES. Our experimental results demonstrate that a VLIW architecture with VLES shows 64% code size decrement on average at the cost of about 4% additional cell area as compared to the case of a VLIW architecture without VLES when instruction duplication is applied to both architectures. Also, it is shown that the case with VLES does not cause extra execution time compared to the case without VLES.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2003.06a
• /
• pp.690-693
• /
• 2003

Soft x-ray microscopy provides a unique set of capabilities in-between those of visible light and electron microscopy. It has long been recognized that nature provides a 'water window' spectral region between the K shell x-ray absorption edges of carbon (~290eV) and oxygen (~540eV), where organic materials show strong absorption and phase contrast, while water is relatively non-absorbing. This enables imaging of hydrated biological specimens that are several microns thick with high intrinsic contrast using x-rays with a wavelength of 2.3~4.4nm. Soft X-ray microscopy is therefore well suited to the study of specimens like single biological cells. The most direct advantage of X-ray microscope is their high spatial resolution when compared with visible light microscopes, combined with an ability to image hydrated specimens that are several microns with a minimum of preparation. Our study describes the conceptual design of soft x-ray microscope system based on a laser-based source for biomedical application with high resolution ($\leq$50nm) and short exposure time ($\leq$30sec).

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.4
• /
• pp.397-402
• /
• 2005

A new control algorithm of soft starter is proposed for the reduction of the inrush current during the grid connection of the induction-type wind power generator. Currently, the fixed speed wind turbine using induction generator is the most popular wind generation system in Korea. It is shown that the amount of inrush current mainly depends on the control algorithm of the soft starter, a thyristor-based grid connection device. For the simulation study, a 600kw wind turbine simulation model is developed and the transient waveforms are investigated with conventional md proposed methods. Also experimental results using 3.7kW experimental set-up show that the peak value of inrush current is reduced about 20$\%$ using proposed algorithm.

• Journal of Environmental Health Sciences
• /
• v.9 no.2
• /
• pp.1-10
• /
• 1983

The purpose of this study was to analyze general ingredient of bean cured on the market and to examine its exposure to bacterial contamination. For this study, 17 samples (each 9 samples for general bean curd, soft bean curd, and uncurdled bean curd) were randomly collected from nine areas in Seoul from the beginning of April, 1983 to the beginning of June, 1983. The result of ingredient analysis of moisture, ash, and protein of bean curd was compared with the standard set by the Ministry of Health & Social Affairs. In order to find out exposure of bean curd on the market to bacterial contamination, total biological bacteria and coliform group were examined. Experimental results were shown as follows 1) Results of ingredient analysis of moisture, ash, and protein of general bean curd showed that total samples in both moisture and protein met the standard set by the Ministry of Health & Social Affairs but 44.4% of the samples in ash was below the above standard, indicating average 82.0%, 0.9% and 9.6% in moisture, ash, and protein order. 2) Experimental results of moisture, ash, and protein of soft bean curd demonstrated 90.2%, 0.5% and 4.3% respectively total samples in both moisture and protein satisfied the self-criteria set by the Soft Food Co-operative Association of Seoul City but 11.1% of the samples in ash didn't meet the self-criteria. 3) Total samples of uncurdled bean curd satisfied the self-criteria set by the above association, indicating average 92.0%, 0.4%, and 3.5% in moisture, ash, and protein order. 4) Total biological bacteria and coliform group detected in general bean curd showed that more than 10$^5$/g in total biological bacteria accounted for 88.8% of the samples and that 10$^4$/g or more in coliform group accounted for 77.7% of the samples. The result proves that general bean curd has been exposured to a severe bacterial contamination. 5) Result of total biological bacteria and coliform group detected in such packed bean curd as uncurdled bean curd and soft bean curd showed that 61.6% of the samples exceeded 10$^6$/g in total biological bacteria and 27.7% of the samples exceeded 10$^3$/g in coliform group. 6) According to the change with time and temperatures in total biological bacteria and coliform group of general bean curd, general bean curd began to decay around 72 hours at 4$\circ$C and around 48 hours at 23$\circ$C and around 24 hours at 37$\circ$C and, at that time, total biological bacteria approached 10$^6$/g while coliform group did 10$^6$/g. The result indicates that temperature has a great effect on bacteria counts and decay.

• Journal of Fashion Business
• /
• v.21 no.1
• /
• pp.58-73
• /
• 2017

The purpose of this study was to examine the need of the eyelash design area and the changes of an eye image according to eyelash design. Methodology included both a theoretical research and an empirical research. The theoretical research reviewed previous researches and technical books. The empirical research divided eye shapes, complemented the defect of eye shapes, and examined resulting image changes. A mechanical way was performed for treatment because it was more efficient than a manual way. A J-curl type was used. Eye length was divided into five and the point was determined. The length and density of curl were changed in each point to maximize a treatment effect. As a result, eye images were changed as follows. First, round eyes became stable. Slit eyes became vivid and soft. Wide-set eyes became intelligent and narrow-set eyes became smooth. Large eyes were naturally gradated and small eyes became larger. Double-eyelid eyes became stable and elegant and single-eyelid eyes became gentle and soft. Bulging eyes became easy and soft and sunken eyes became smooth. Peaked eyes became gentle and soft and sleepy eyes became strong and vivid. Based on the findings, eyelash design can play a role in changing an image according to eye shapes. In particular, a speed eyelash extension device to extend eyelash can reduce working hours and gradate only by angle control. It can complement the defect of eyes according to the design of each shape and change into a better image.