• Korean Journal of Materials Research
• /
• v.20 no.8
• /
• pp.408-411
• /
• 2010

Indium doped $SnO_2$ thick films for gas sensors were fabricated by a screen printing method on alumina substrates. The effects of indium concentration on the structural and morphological properties of the $SnO_2$ were investigated by X-ray diffraction and Scanning Electron Microscope. The structural properties of the $SnO_2$:In by X-ray diffraction showed a (110) dominant $SnO_2$ peak. The size of $SnO_2$ particles ranged from 0.05 to $0.1\;{\mu}m$, and $SnO_2$ particles were found to contain many pores, according to the SEM analysis. The thickness of the indium-doped $SnO_2$ thick films for gas sensors was about $20\;{\mu}m$, as confirmed by cross sectional SEM image. Sensitivity of the $SnO_2$:In gas sensor to 2000 ppm of $CO_2$ gas and 50 ppm of H2S gas was investigated for various indium concentrations. The highest sensitivity to $CO_2$ gas and H2S gas of the indium-doped $SnO_2$ thick films was observed at the 8 wt% and 4 wt% indium concentration, respectively. The good sensing performances of indium-doped $SnO_2$ gas sensors to $CO_2$ gas were attributed to the increase of oxygen vacancies and surface area in the $SnO_2$:In. The $SnO_2$:In gas sensors showed good selectivity to $CO_2$ gas.

• Transactions on Electrical and Electronic Materials
• /
• v.15 no.4
• /
• pp.217-220
• /
• 2014

We studied the plating properties of Sn-Pb solder according to the shape of the Cu wire's cross-section for photovoltaic ribbon. The thickness of the Sn-Pb layer largely decreased to 29% on a curved Cu surface, compared to a flat Cu surface. This phenomenon is caused by the geometrical decrease in the contact angle of the liquid Sn-Pb solder and an increase in the surface energy of the solid/vapor on the curved Cu surface. We suggest a new ribbon's design where the Cu wire's cross-section is a semi-ellipse. These semi-ellipse ribbons can decrease the use of Sn-Pb solder to 64% and increase the photovoltaic efficiency, by reducing the contact area between the ribbon and cell, to 84%. We also see an improvement of reflectivity in the curved surface.

• Convergence Security Journal
• /
• v.18 no.1
• /
• pp.93-102
• /
• 2018

The drug trade among the general public via the Internet and sns have been increasing, which is becoming a social problem. The general public believe that even if they do the drug trade via the Internet and sns the probability of detection is low. so they will conduct drug trade via the Internet and sns. Therefore, if the general public recognize that there is a high likelihood of disclosure, drug trade via the Internet and sns are likely to decline. If the possibility of punishment increases through specification of controlled delivery techniques and Introduction of entrapment investigator, it seems that the general public can not easily deal with drug trade via the Internet and sns. Also by further subdividing the penalties for drug offenses, for simple drug buyers through cure-oriented treatment rather than punishment drug demand be suppressed and penalties for drug suppliers should be strengthened.

• Advances in materials Research
• /
• v.13 no.1
• /
• pp.55-62
• /
• 2024

Cu-based sulfides have recently emerged as promising thermoelectric (TE) materials due to their low cost, non-toxicity, and abundance. In this research, point defect structure of Cu_2-xZnSnS₄ (x=0.1, 0.2, 0.3) samples were synthesized by the mechanical alloying method. Mixed powders of Cu, Zn, Sn and S were milled using high energy ball milling at a rotation speed of 300 rpm in Ar atmosphere. The milled Cu_2-xZnSnS₄ powders were heat-treated at 723 K for 24 h, and subsequently consolidated using spark plasma sintering (SPS) under an applied pressure of 60 MPa for 15 min. The thermal conductivity of the sintered Cu_2-xZnSnS₄ samples was evaluated. A well-defined Cu_2-xZnSnS₄ powders were successfully formed after milling for 16 h, with the particle sizes mostly distributed in the range of 60-100 nm. The lattice constants of aand cdecreased with increasing composition value x. The thermal conductivity of sintered x=0.1 sample exhibited the lowest value and attained 0.93 W/m K at 673 K.

• Journal of the Microelectronics and Packaging Society
• /
• v.27 no.3
• /
• pp.69-72
• /
• 2020

In this study, the inverted structured electroluminescence (EL) devices were fabricated with double electron transport layers (ETLs). The conduction band minimum (CBM) of TiO₂ NPs is lower than SnO₂ NPs. Therefore, it is expected that inserting TiO₂ NPs between the SnO₂ layer and the emission layer (EML) will reduce the energy barrier and transport electrons smoothly. The quantum dot light emitting diodes (QLEDs) with double ETLs showed the enhanced emission characteristics than those with only SnO₂ layer.

• Korean Journal of Materials Research
• /
• v.23 no.6
• /
• pp.304-308
• /
• 2013

The effect of a sputter deposition sequence of Cu, Zn, and Sn metal layers on the properties of $Cu_2ZnSnS_4$ (CZTS) was systematically studied for solar cell applications. The set of Cu/Sn/Zn/Cu multi metal films was deposited on a Mo/$SiO_2$/Si wafer using dc sputtering. CZTS films were prepared through a sulfurization process of the Cu/Sn/Zn/Cu metal layers at $500^{\circ}C$ in a $H_2S$ gas environment. $H_2S$ (0.1%) gas of 200 standard cubic centimeters per minute was supplied in the cold-wall sulfurization reactor. The metal film prepared by one-cycle deposition of Cu(360 nm)/Sn(400 nm)/Zn(400 nm)/Cu(440 nm) had a relatively rough surface due to a well-developed columnar structure growth. A dense and smooth metal surface was achieved for two- or three-cycle deposition of Cu/Sn/Zn/Cu, in which each metal layer thickness was decreased to 200 nm. Moreover, the three-cycle deposition sample showed the best CZTS kesterite structures after 5 hr sulfurization treatment. The two- and three-cycle Cu/Sn/Zn/Cu samples showed high-efficient photoluminescence (PL) spectra after a 3 hr sulfurization treatment, wheres the one-cycle sample yielded poor PL efficiency. The PL spectra of the three-cycle sample showed a broad peak in the range of 700-1000 nm, peaked at 870 nm (1.425 eV). This result is in good agreement with the reported bandgap energy of CZTS.

• The Journal of the Convergence on Culture Technology
• /
• v.7 no.1
• /
• pp.17-23
• /
• 2021

Social media users are an important part of our lives as they spend a lot of time and actively use them. However, it is known that there are many users who feel the psychological stress of SNS stress or fall into addiction due to SNS use. SNS stress negatively affects not only the user's mind but also the body. This study investigates the associations between SNS stress and addiction. To test the hypotheses, the study performed structural equation modeling using Amos. We collected 210 data from SNS users. The empirical results showed that SNS overuse had a significant effect on SNS stress. Second, SNS stress had a significant relationship with SNS addiction. Third, it was found that SNS overuse did not directly affect SNS addiction. This study suggests that it is necessary to recognize the importance of the relationship between SNS addiction and SNS stress.

• Journal of the Korean Ceramic Society
• /
• v.33 no.4
• /
• pp.379-384
• /
• 1996

The H2S sensing mechanism of CuO-SnO2 was confirmed by analyzing the electrical-resistance variation with temperature under an H2S atmosphere. While the resistance of CuO-SnO2 thick film at N2+H2S atmosphere was almost invariant with change in temperature it increased with increasing temperature for air +H2S atmos-phere. This behavior was analyzed using an equation derived from a basic assumption based on the H2S sensing mechanism proposed before. the experimental results are sufficiently explained with the equation derived which showed that the H2S sensing mechanism was reasonable. The equation also gave a detailed analysis and physical meaning to the behavior of the resistance variation with change in H2S concentration.

• The Journal of the Korea Contents Association
• /
• v.19 no.4
• /
• pp.138-149
• /
• 2019

The purpose of this study is to empirically address the influences of motives for using SNS on relational bridging and relational bonding in SNS and motives for continuous use SNS by applying the concepts of bonding and bridging, defined in the social capital theory, and major motives for using SNS are classified into three categories-social, information, and recreation categories - based on the previous studies and the usage and gratification theories. Through this study, it was revealed that motives of all these three categories-social, information, and recreation categories-have significant influences over relational bridging and relational bonding in SNS while relational bridging and relational bonding in SNS have significant influences over consistent motives for using SNS so the hypothesis of this study is accepted. It was also proven that motives of all these three categories - social, information, and recreation categories-for using SNS are important factors for creating new communities or expand relationships with other SNS users sharing similar interests. In addition, it was found that SNS users constantly use SNS to build relationships that could create a strong bond between individuals and receive emotional supports when necessary and to expand its own network by creating new relationships with other SNS users.

• Proceedings of the International Microelectronics And Packaging Society Conference
• /
• 2000.04a
• /
• pp.81-86
• /
• 2000

To evaluate the possibility of the partial melting soldering. wettability of partial melted solders was measured using wetting balance. Off eutectic Sn-Pb allows are wettable in their partial melting zone. Especially, Pb rich alloys showed excellent wettability while wettability of Sn rich alloys were adequate or poor. It is found that wettability increases over $200^{\circ}C$ regardless of composition liquid fraction and phases of the original alloy Sn-7Ag alloy showed good wettability in their partial melting zone, while Sn-65Bi alloy was non-wettable under their melting points.