• Proceedings of the Materials Research Society of Korea Conference
• /
• 1998.08a
• /
• pp.118.3-118
• /
• 1998

• Industry Promotion Research
• /
• v.1 no.2
• /
• pp.7-11
• /
• 2016

$SnO_2$ films were annealed in a vacuum atmosphere conditions to research the temperature dependency of current-voltage characteristics, crystal structure and chemical properties. The $SnO_2$ film annealed in a vacuum became an amorphous structure, but the degree of amorphous structure changed in accordance with the content of oxygen vacancy, which increased at film annealed at $100^{\circ}C$ and then decreased over the sample at annealed at $150^{\circ}C$. Because the crystallinity was affected the content of oxygen vacancy. The oxygen vacancy as carriers disappeared with increasing the annealing temperatures, and the depletion layer increased. Therefore the content of exiton as optical properties increased with becoming the amorphous structure. So the intensity of PL spectra increased with increasing the annealing temperature.

• Proceedings of the KIEE Conference
• /
• 2004.07c
• /
• pp.1555-1557
• /
• 2004

The Pt-doped $SnO_2$ thin film for CO sensor applications obtained by RF sputtering from a target of the same compound in an Ar-$O_2$ atmosphere. Pt-SnO2-SiC Schottky diode detection of CO gas Cause the remarkable change in electrical resistivity of the semiconductor. the good gas sensitivity is shown when annealing condition is 600$^{\circ}C$, 1hr in RTP and detected temperature is 350$^{\circ}C$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.93-93
• /
• 2011

The Indium Zinc Tin Oxide (IZTO) and Indium Tin Oxide (ITO) thin films are grown on PI substrate at different substrate temperature by pulsed DC magnetron sputtering with a sintered ceramic target of IZTO (In2O3 70 wt.%, ZnO 15 wt.%, SnO2 15 wt.%) and ITO (In2O3 90wt.%, SnO2 10wt.%). The structural, electrical, and optical properties are investigated. The IZTO thin films deposited at low temperature showed relatively low electrical resistivity compared to ITO thin films deposited at low temperature. As a result, we could prepare the IZTO thin films with the resistivity as low as $5.6{\times}10^{-4}({\Omega}{\cdot}m)$. Both of the films deposited on PI substrate showed an average transmittance over 80% in visible range (400.800nm). Overall, IZTO thin film is a promising candidate as an alternative TCO material to ITO in flexible and OLED devices.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2010.08a
• /
• pp.166-166
• /
• 2010

Recently, TFTs based on amorphous oxide semiconductors (AOSs) such as ZnO, InZnO, ZnSnO, GaZnO, TiOx, InGaZnO(IGZO), SnGaZnO, etc. have been attracting a grate deal of attention as potential alternatives to existing TFT technology to meet emerging technological demands where Si-based or organic electronics cannot provide a solution. Since, in 2003, Masuda et al. and Nomura et al. have reported on transparent TFTs using ZnO and IGZO as active layers, respectively, much efforts have been devoted to develop oxide TFTs using aforementioned amorphous oxide semiconductors as their active layers. In this thesis, I report on the performance of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer at room temperature. $SiO_2$ was employed as the gate dielectric oxide. The amorphous indium gallium zinc oxides were deposited by RF magnetron sputtering. The carrier concentration of amorphous indium gallium zinc oxide was controlled by oxygen pressure in the sputtering ambient. Devices are realized that display a threshold voltage of 1.5V and an on/off ration of > $10^9$ operated as an n-type enhancement mode with saturation mobility with $9.06\;cm^2/V{\cdot}s$. The devices show optical transmittance above 80% in the visible range. In conclusion, the fabrication and characterization of thin-film transistors using amorphous indium gallium zinc oxides for an active channel layer were reported. The operation of the devices was an n-type enhancement mode with good saturation characteristics.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.347.2-347.2
• /
• 2014

최근, 비정질 산화물 반도체 thin film transistor (TFT)는 수소화된 비정질 실리콘 TFT와 비교하여 높은 이동도와 큰 on/off 전류비, 낮은 구동 전압을 가짐으로써 빠른 속도가 요구되는 차세대 투명 디스플레이의 TFT로 많은 연구가 진행되고 있다. 한편, 기존의 Thin-Film-Transistor 제작 시 우수한 박막을 얻기 위해서는 $500^{\circ}C$ 이상의 높은 열처리 온도가 필수적이며 이는 유리 기판과 플라스틱 기판에 적용하는 것이 적합하지 않고 높은 온도에서 수 시간 동안 열처리를 수행해야 하므로 공정 시간 및 비용이 증가하게 된다는 단점이 있다. 이러한 점을 극복하기 위해 본 연구에서는 간단하고, 낮은 제조비용과 대면적의 박막 증착이 가능한 용액공정을 통하여 박막 트랜지스터를 제작하였으며 thermal 열처리와 microwave 열처리 방식에 따른 전기적 특성을 비교 및 분석하고 각 열처리 방식의 열처리 온도 및 조건을 최적화하였다. P-type bulk silicon 위에 산화막이 100 nm 형성된 기판에 spin coater을 이용하여 Al-Zn-Sn-O 박막을 형성하였다. 그리고, baking 과정으로 $180^{\circ}C$의 온도에서 10분 동안의 열처리를 실시하였다. 연속해서 Photolithography 공정과 BOE (30:1) 습식 식각 과정을 이용해 활성화 영역을 형성하여 소자를 제작하였다. 제작 된 소자는 Junctionless TFT 구조이며, 프로브 탐침을 증착 된 채널층 표면에 직접 접촉시켜 소스와 드레인 역할을 대체하여 동작시킬 수 있어 전기적 특성을 간단하고 간략화 된 공정과정으로 분석할 수 있는 장점이 있다. 열처리 조건으로는 thermal 열처리의 경우, furnace를 이용하여 $500^{\circ}C$에서 30분 동안 N2 가스 분위기에서 열처리를 실시하였고, microwave 열처리는 microwave 장비를 이용하여 각각 400 W, 600 W, 800 W, 1000 W로 15분 동안 실시하였다. 그 결과, furnace를 이용하여 열처리한 소자와 비교하여 microwave를 통해 열처리한 소자에서 subthreshold swing (SS), threshold voltage (Vth), mobility 등이 비슷한 특성을 내는 것을 확인하였다. 따라서, microwave 열처리 공정은 향후 저온 공정을 요구하는 MOSFET 제작 시의 훌륭한 대안으로 사용 될 것으로 기대된다.

• Korean Journal of Materials Research
• /
• v.17 no.7
• /
• pp.376-381
• /
• 2007

Fluorine-doped tin oxide (FTO) thin film was coated on aluminosilicate glass at $450^{\circ}C$ by spray pyrolysis method. In the range of 0-2.7 molar ratio of F/Sn, the variations of electrical conductivity and visible light transmission were investigated. At the F/Sn ratio of 1.765, the film showed the lowest electrical resistivity value of $3.0{\times}10^{-4}{\Omega}\;cm$, the highest carrier concentration of $2.404{\times}10^{21}/cm^3$, and about $8\;cm^2/V{\cdot}sec$ of electronic mobility. The FTO film showed a preferred orientation of (200) plane parallel to the substrate. X-ray photoelectron spectroscopy analysis results indicated that the contents of $Sn^{4+}-O$ bonding are the highest at 1.765 of F/Sn molar ratio.

• Journal of the Korean Vacuum Society
• /
• v.4 no.S2
• /
• pp.95-99
• /
• 1995

keV ion beam irradiatin for surface modification and thin film growth have been discussed. keV ion beam irradiation in reactive gas environment has been developed for improving wettability of polymer, and for enhancing adhesion to metal film, and adventages of the method have been reviewed. An epitaxial Cu film on Si(100) substrate has been grown by ionized cluster beam and changes of crystallinity and surface roughness have been discussed. Stoichiometric $SnO_2$ films on Si(100) and glass have been grown by a hybrid ion beam Deposition(2 metal ion sources+1 gas ion source), and nonstoichiometric $SnO_2$ films are controlled by various deposition conditions in the HIB. Surface modification for polymer by kev ion irradiation have been developed. Wetting angle of water to PC has been changed from 68 degree to 49 degree with $Ar^+$ irradiation and to 8 degree with $Ar^+$ irradiation and the oxygen environment. Change of surface phenomena in a keV ion beam and characteristics of the grown films are suggested.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.203-204
• /
• 2009

The Indium Zinc Tin Oxide (IZTO) thin films for flexible display electrode were deposited on poly carbonate (PC) and polyethersulfone(PES) and glass substrates at room temperature by facing targets sputtering (FTS). Two different kinds of targets were installed on FTS system. One is ITO ($In_2O_3$ 90 wt.%, $SnO_2$ 10 wt.%), the other is IZO ($In_2O_3$ 90 wt.%, ZnO 10 wt.%). As-deposited IZTO thin films were investigated by a UV/VIS spectrometer, an X-ray diffractometer (XRD), an atomic force microscope (AFM) and a Hall Effect measurement system. As a result, we could prepare the IZTO thin films with the resistivity of under $10^{-4}\;[{\Omega}{\cdot}cm]$ and IZTO thin films deposited on glass substrate showed an average transmittance over 80% in visible range (400~800 nm) in all IZTO thin films except in IZTO thin film deposited at $O_2$ gas flow rate of 0.1[sccm].

• Journal of Ocean Engineering and Technology
• /
• v.21 no.1 s.74
• /
• pp.59-63
• /
• 2007

The thin film of indium tin oxide (ITO) was prepared using the inclination opposite target type DC magnetron sputtering equipment onto the glass substrate at room temperature, using oxidized ITO with In2O3 and SnO2in a weight ratio of 9:1. The elastic modulus and hardness of the ITO thin films, prepared at different deposition conditions, were determined through anano-indentation experiment. The work pressure was varied from $2.6{\times}10-1\;to\;8.3{\times}10-1Pa$. The results show that the variation of work pressure during film deposition could vary significantly, according to the elastic modulus and hardness of the ITO thin films. It also can be seen that a minimum value exists in the film resistivity for the ITO thin films, prepared according to the variation of work pressure. However, the ITO film produced at room temperature had a microstructure in which a X ray diffraction peak is not clear, regardless of the work pressure.