• 한국재료학회지
• /
• 제24권9호
• /
• pp.451-457
• /
• 2014

We developed a high-performance methane gas sensor based on a $SnO_2$ hollow hemisphere array structure of nano-thickness. The sensor structures were fabricated by sputter deposition of Sn metal over an array of polystyrene spheres distributed on a planar substrate, followed by an oxidation process to oxidize the Sn to $SnO_2$ while removing the polystyrene template cores. The surface morphology and structural properties were examined by scanning electron microscopy. An optimization of the structure for methane sensing was also carried out. The effects of oxidation temperature, film thickness, gold doping, and morphology were examined. An impressive response of ~220% was observed for a 200 ppm concentration of $CH_4$ gas at an operating temperature of $400^{\circ}C$ for a sample fabricated by 30 sec sputtering of Sn, and oxidation at $800^{\circ}C$ for 2 hr in air. This high response was enabled by the open structure of the hemisphere array thin films.

• 한국세라믹학회지
• /
• 제37권7호
• /
• pp.686-692
• /
• 2000

Tin-doped In2O3 (ITO) films were fabricated using a d.c. magnetron reactive sputteirng of a In-10 wt% Sn alloy target in an Ar and O2 gas mixture. To understand the behavior of the carrier mobility in ITO films with O2 partial pressure, the resistivity, carrier concentration and mobility, film density, and intrinsic stress in the films were measured with O2 partial pressure. It was found experimentally that the carrier mobility increased rapidly as the film density increased. In the ITO film with the density close to theoretical one, the mean free path was the same as the columnar diameter. This indicated that the mobility in ITO films was strongly influenced by the crystall size. However, in the case where the film density was smaller than a theoretical density, the mean free paths were also smaller the columnar diameter. It was analyzed that the electron scattering at pores and holes within the crystalline was the major obstacle for electron conduction in ITO films. The measurement of intrinsic stress in ITO films also made it clear that the density of ITO films was controlled by the bombardment of oxygen neutrals on the growing film.

• Journal of Ceramic Processing Research
• /
• 제13권spc2호
• /
• pp.394-397
• /
• 2012

In this work, we studied the influence of the dopant elements concentration on the properties of SnO2 thin films deposited by pulsed laser deposition. X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), Hall effect measurement and UV-Vis studies were performed to characterize the deposited films. XRD results showed that the films had polycrystalline nature with tetragonal rutile structure. FE-SEM micrographs revealed that the as deposited films composed of dense microstructures with uniform grain size distribution. All the films show n-type conduction and the best transparent conductive oxide (TCO) performance was obtained on 6 wt% Sb2O5 doped SnO2 film prepared at pO2 of 60mtorr and Ts of 500 ℃. Its resitivity, optical transmittance, figure of merit are 7.8 × 10-4 Ω cm, 85% and 1.2 × 10-2 Ω-1, respectively.

• 한국표면공학회지
• /
• 제44권4호
• /
• pp.144-148
• /
• 2011

$Ga_2O_3$ doped $SnO_2$ thin films were grown by using pulsed laser deposition (PLD) technique on glass substrate. The optical and electrical properties of these films were investigated for different doping concentrations, oxygen partial pressures, substrate temperatures, and film thickness. The films were deposited at different substrate temperatures (room temperature to $600^{\circ}C$). The best opto-electrical properties is shown by the film deposited at substrate temperature of $300^{\circ}C$ with oxygen partial pressure of 80 m Torr and the gallium concentration of 2 wt%. The as obtained lowest resistivity is $9.57{\times}10^{-3}\;{\Omega}cm$ with the average transmission of 80% in the visible region and an optical band gap (indirect allowed) of 4.26 eV.

• 한국전기전자재료학회논문지
• /
• 제22권3호
• /
• pp.269-276
• /
• 2009

Antimony doped tin oxide ($SnO_2:Sb$) films, which are used as the front contact and back reflector of thin film solar cells, have been deposited by d,c, magnetron sputtering. The dependence of electrical and optical properties of the films on the preparation conditions, such as $O_2$ gas ratio, substrate temperature, annealing temperature was investigated. The sputter gas composition was found to affect the properties of the films. With incorporating $O_2$ gas, the electrical and optical properties of films significantly were improved. The minimum resistivity and optical transmittance over 80 % in visible region were obtained at the oxygen concentration of 30 %, When the substrate temperature was higher, the resistivity of $SnO_2:Sb$ films was decreased, while the absorption edge shifted to shorter wavelength, indicating higher optical band gap. Heat treatment over $600^{\circ}C$ resulted in poorer electrical and optical properties due to SnO phase (102) plane.

• 한국표면공학회:학술대회논문집
• /
• 한국표면공학회 1999년도 추계학술발표회 초록집
• /
• pp.65-66
• /
• 1999

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2002년도 추계총회 및 연구발표회 초록집
• /
• pp.183.1-183
• /
• 2002

• Journal of Information Display
• /
• 제10권4호
• /
• pp.137-142
• /
• 2009

Transparent top-gate Al-Zn-Sn-O (AZTO) thin-film transistors (TFTs) with an $Al_2O_3$ protective layer (PL) on an active layer were studied, and a transparent 2.5-inch QCIF+AMOLED (active-matrix organic light-emitting diode) display panel was fabricated using an AZTO TFT backplane. The AZTO active layers were deposited via RF magnetron sputtering at room temperature, and the PL was deposited via two different atomic-layer deposition (ALD) processes. The mobility and subthreshold slope were superior in the TFTs annealed in vacuum and with oxygen plasma PLs compared to the TFTs annealed in $O_2$ and with water vapor PLs, but the bias stability of the TFTs annealed in $O_2$ and with water vapor PLs was excellent.

• 한국전기전자재료학회논문지
• /
• 제29권9호
• /
• pp.546-551
• /
• 2016

$SrSnO_3:Tb^{3+}$ phosphor thin films were prepared on sapphire and quartz substrates in the growth temperature range of $100{\sim}400^{\circ}C$ by using the radio frequency magnetron sputtering deposition. The resulting $SrSnO_3:Tb^{3+}$ thin films were characterized by X-ray diffraction, scanning electron microscopy, ultraviolet-visible-infrared spectrophotometer, and photoluminescence spectrometer. The results indicated that the morphology, optical transmittance, band gap energy, and luminescence intensity of the phosphor thin films significantly depended on the growth temperature. All the thin films, regardless of the type of substrate, showed an amorphous behavior. As for the thin films deposited on sapphire substrate, the maximum crystallite size was obtained at a growth temperature of $400^{\circ}C$ and the strongest emission was green at 544 nm arising from the $^5D_4{\rightarrow}^7F_5$ transition of Tb3+. The average optical transmittance for all the thin films grown on sapphire and quartz substrates was decreased as the growth temperature increased from 100 to $400^{\circ}C$. The results suggest that the optimum growth temperatures for depositing highly-luminescent $SrSnO_3:Tb^{3+}$ phosphor thin films on sapphire and quartz substrates are 400 and $300^{\circ}C$, respectively.

• 한국세라믹학회지
• /
• 제23권5호
• /
• pp.81-85
• /
• 1986

$SnO_2$ thin films have been prepared by chemical vapor deposition technique. Electrical and optical properties of the films have been investigated. It is found that the electrical condictivity and optical transparency of the films are most affected by deposition temperature and more affected by $SnCl_4$ partial pressure than by $O_2$ partial pressure. Experimental results show that the conductivity increases with high optical transparency as deposition temperature increases up to 50$0^{\circ}C$ but the conductivity decreases with the loss of transparency as deposition temperature increases above $600^{\circ}C$.