• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2003.11a
• /
• pp.360-367
• /
• 2003

Diamond-like carbon(DLC) films are considerable research interest because of their widespread applications as protective coatings in areas such as optical windows, magnetic storage disks, car parts, biomedical coatings and as micro-electromechanical devices(MEMs). DLC films were deposited on WC-Co by PECVD using Ar, $C_2H_4$ gas. Tribological tests were conducted using a ball-on-disk type tribometer in dry air. Three kinds of counter-bodies balls were used. The counter-bodies balls are SM45C, SUJ2 and $ZrO_2$(3.17mm in diameter). Wear rate of the samples were calculated after measuring the worn-out volume of the wear track. As results wear test, the higher hardness of counter-bodies, friction coefficient low. As result of XPS estimation, wear debris generated as an oxide lower the friction coefficient.

• Journal of Magnetics
• /
• v.16 no.2
• /
• pp.192-195
• /
• 2011

The phase transition of vortex matter from solid to liquid was studied in iron-based superconductors. Based on the traditional vortex glass theory, we have examined the magnetoresistivity data of iron-based superconductors using our extended thermal activation model: $\rho(B,T)=\rho((T-T_g(B))/(T_c(0)-T_g(B)))^{v(z-1)}$. We predict that the magnetic field-dependent area S + $S_0$ which integrates $\rho$ with T is proportional to $B^{\beta}$, where ${\beta}$ is the vortex glass transition exponent. From our calculation, the vortex glass transition exponent is 0.33, close to the exponent of area $S_0$ + S is 0.31 in $SmO_{0.9}F_{0.1}FeAs$; the exponent of area S is 0.63, which is close to the irreversibility line exponent 2/3. Both of the results show the validity of our model. In addition, our model is shown to be effective in describing irreversibility behavior in layered superconductors.

• Nuclear Engineering and Technology
• /
• v.56 no.9
• /
• pp.3545-3552
• /
• 2024

Polymers have become widely used substrate materials for shielding neutron rays because of their high hydrogen content and easy processing procedures. Rare-earth materials are also being gradually adopted as neutron absorbers because of their considerable thermal neutron absorption cross-sections. This paper utilizes the FLUKA Monte Carlo simulation program to compare the shielding effects of various polymers and rare-earth oxides on neutron rays across different energy ranges. The study investigates the superior shielding materials for neutron radiation in each energy range. Subsequently, a series of materials are simulated by combining the preferred shielding materials for neutron rays in each energy range, exploring the influence of material composition and composite structure on the effectiveness of neutron ray shielding. It is revealed that the preferred material for shielding neutron rays changes for different energy ranges. For low-energy neutron rays, rare-earth oxides such as Sm₂O₃ and Gd₂O₃ demonstrate the most effective shielding, whereas for high-energy neutron rays, polyethylene (PE) provides the best shielding performance. Materials with different compositions show varying preferred structures when dealing with a ²⁵²Cf neutron source. However, in mitigating the secondary gamma rays generated during the neutron shielding process, stacked-type materials exhibit the most effective shielding performance.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.13 no.1
• /
• pp.121-128
• /
• 2014

Superfinishing is essential for mirror surfaces, because among mechanical components cylindrical workpieces such as spindles must maintain precision and reliability with respect to functional characteristics. However, research on standardization of polishing film application combination to obtain mirror surfaces is insufficient. Consequently, this has been a factor in rising costs of mechanical components. Therefore, in this study, experiments have been conducted to determine efficient polishing film application combination for mirror surfaces ranging from ductile materials such as SM45C, brass, aluminium 7075, and titanium to brittle materials such as $Al_20_3$, SiC, $Si_3N_4$, and $ZrO_2$. From the experimental results, efficient polishing film application combination for metallic materials and ceramic materials is confirmed.

• Journal of the korean academy of Pediatric Dentistry
• /
• v.35 no.3
• /
• pp.427-436
• /
• 2008

Purpose. The objective of this study was to evaluate the behavioral response and assess the effectiveness of additional intranasal (IN) and submucosal (SM) administration of midazolam during pediatric sedation for dental procedure. Material and methods. Thirty-three cases of healthy (ASAⅠ), uncooperative children aged from 24 to 72 month old at pediatric dental clinic of Ewha Womans University Hospital were selected for this study. Children received oral chloral hydrate 50 mg/kg with hydroxyzine 1.0 mg/kg. After waiting for 45 minutes, midazolam 0.2 mg/kg was administrated via IN route and via SM route randomly maintaining 50% of $N_2O$. A pulse oximeter and a capnograph were used for measuring vital signs ($SpO_2$, PR, RR, $EtCO_2$) throughout the sedation. Behavioral response was evaluated as Quiet (Q), Crying (C), Movement (M) or Struggling (S) in every 2 minutes for 40 minutes. Results. There were also no statistically significant differences in vital signs of the two groups. The behavioral response for the first ten minutes during sedation was a statistically significant difference (P < 0.05) between the two groups. After the first ten minutes, it was revealed that there was no significant difference. Conclusion. This study demonstrated that the addition of IN midazolam to the combination of oral chloral hydrate with hydroxyzine and nitrous oxide/oxygen inhalation is as safe and effective as that of SM midazolam in pediatric sedation for dental procedure.

• Progress in Superconductivity and Cryogenics
• /
• v.9 no.2
• /
• pp.23-26
• /
• 2007

The influence of water partial pressure in Metal-organic Deposition (MOD) method was investigated on the texture and the morphology of $YBa_2Cu_3O_{7-x}$ (YBCO) films grown on the buffered metal tapes. The water partial pressure was varied from 4.2% up to 10.0% with the other process variables, such as annealing temperature and oxygen partial pressure, kept constant. In this work, the fluorine-free Y & Cu precursor solution added with Sm was synthesized and coated by the continuous slot-die coating & calcination step. The next annealing step of the YBCO films was done by the reel-to-reel method with the gas flowed vertically down. From the x-ray diffraction analysis, the un-reacted phase like $BaF_2$ peak was found at the water partial pressure of 4.2%, but $BaF_2$ peak intensity is much reduced as the water partial pressure is increased. However, the higher water partial pressure of about 10% in this experiment leads to the poor crystallinity of YBCO films. The morphologies of the YBCO films were not different from each other when the water partial pressure was varied in this work. The maximum critical current density of 3.8MA/$cm^2$ was obtained at the water partial pressure of 6.2% with the annealing temperature of 780$^{\circ}C$ and oxygen partial pressure of 500ppm.

• Journal of the Korean Ceramic Society
• /
• v.48 no.6
• /
• pp.589-594
• /
• 2011

Raw mix of molten clinker was fabricated using blast furnace slag as starting material. Raw mix was melted at 1620$^{\circ}C$ for molten clinker fabrication. It was found that molten clinker contained alite and belite equivalent to OPC clinker mineral by optical microscope and SEM. The size of alite was 10~50 ${\mu}m$ and that of belite was 20~80 ${\mu}m$. This result thought to be attributed low $Al_2O_3$ content and cooling condition. Interstitial phase increased with blast furnace slag content and gehlenite was formed by the condition of LSF and SM. So raw mix with 27~41% blast furnace slag could be converted into cement clinker by appropriate choice of melting andcooling methods in this study.

• Economic and Environmental Geology
• /
• v.34 no.6
• /
• pp.627-648
• /
• 2001

At least two distinct types of layering are present in the middle zone of the Skaergaard intrusion; alternating plagioclase-rich and pyroxene-rich, macro-rhythmic layers, and smaller scale, modally-graded, rhythmic layers. The macro-rhythmic layers are ubiquitous in the middle zone of the Layered Series, but are not observed in the lower and upper zone of the Layered Series or in the wall or roof tories of the intrusion. They range from 0.3 to 17.3 m in thickness, have sharp upper and lower boundaries, and can be traced laterally for over 2 ]fm in outcrop. Although individual macrorhythmic layers are not internally graded, many contain smaller-scale, modally-graded layers. Modally-graded. rhythmic layers are a common feature of the Layered Series but are not abundant in either the Upper Border Series or the Marginal Border Series. They range in thickness from 1 to 50 cm and can be traced laterally in outcrop for up to 100 m. Their lateral termination ranges from abrupt to gradational, and they are often associated with cut and fill structures and crossbedding suggestive of current activity. They are characterized by sharp lower and gradational upper contacts, and by strong intra-layer modal grading with olivine, ilmenite, and magnetite concentrated at the base, pyroxene concentrated above the base, and plagioclase concentrated at the top. The layers are also grain-size graded with the maximum size for each phase occurring at the horizon in the layer where the phase is most abundant. Modally-graded, rhythmic layers in the middle zone of the Layered Series occur within both plagioclase-rich and pyroxene-rich macro-rhythmic layers.

• Journal of the Korean Society for Heat Treatment
• /
• v.14 no.2
• /
• pp.103-109
• /
• 2001

Plasma nitrocarburising and post oxidation were performed on SM45C steel using a plasma nitriding unit. Nitrocarburising was carried out with various methane gas compositions with 4 torr gas pressure at $570^{\circ}C$ for 3 hours and post oxidation was carried out with 100% oxygen gas atmosphere with 4 torr at different temperatures for various times. It was found that the compound layer produced by plasma nitrocarburising consisted of predominantly ${\varepsilon}-Fe_{2-3}(N,C)$ and a small proportion of ${\gamma}-Fe_4(N,C)$. With increasing methane content in the gas mixture, ${\varepsilon}$ phase compound layer was favoured. In addition, when the methane content was further increased, cementite was observed in the compound layer. The very thin oxide layer on top of the compound layer was obtained by post oxidation. The formation of Oxide phase was initially started from the magnetite($Fe_3O_4$) and with increasing oxidation time, the oxide phase was increased. With increasing oxidation temperature, oxide phase was increased. However the oxide layer was split from the compound layer at high temperature. Corrosion resistance was slightly influenced by oxidation times and temperatures.

• Economic and Environmental Geology
• /
• v.32 no.4
• /
• pp.323-337
• /
• 1999

Late Cretaceous to early Tertiary volcanic rocks in the Kyongsang basin exhibit high-K calc-alkaline characteristics, and originated from the magmatism related genetically to subduction of Kula-Pacific plate. They represent HFSE depletion and LlLE enrichment characteristics as shown by magmas related to subduction. Early studies on the depth of magma generation has been estimated as 180-230 km based on K-h relation should be reevaluated, because the depth of peridotite partial melting with 0.4 wt. % water is 80-120 km at subduction zone, and subducting slab in premature arc can melted even lower than 70 km. Moreover the increase of potassium contents depends on either contamination of crustal material and fluids of subducting slab or low degree of partial melting. If the inclination of subduction zone is 30 degrees and the depth to the Benioff zone is 180-230 km, the calculated distance between the volcanic zone and trench axis would be 310-400 km. It is unlikely because the distance between the Kyongsang basin and trench during late Cretaceous to early Tertiary is closer than this value and not comparable with generally-accepted models in subduction zone magmatism. $K_{55}$ of the volcanics in the Kyongsang basin is 0.3-2.3 wt.% and the average indicate that the depth ranges between 80-170 km on the diagram of Marsh, Carmichael (1974). Fractionation from garnet lherzolite, assumed the depth of 180-230km, is not consistent with the REE patterns of the volcanoes in the Kyongsang basin. Futhermore, the range of depth suggested by many workers, who studied magmatism related to subduction, imply shallower than this depth. Crustal thickness calculated by the content of CaO and $Na_2O$ is about 30 km and about 35 km, respectively. Paleo-crustal thickness during late Cretaceous to early Tertiary times in the Kyongsang basin inferred about 30 km calculated by La/Sm versus LaJYb data, which is also supported by many previous studies.