• Proceedings of the KSME Conference
• /
• 2003.04a
• /
• pp.376-380
• /
• 2003

The microstructure and the mechanical properties of RS-SiC and RS-$SiC_f/SiC$ materials have been investigated in conjunction with the content of residual silicon and porosity. The mechanical properties of RS-SiC materials suffered from the thermal exposure were also examined. RS-SiC based materials bave been fabricated using the complex matrix slurry with different composition ratios of SiC and C panicles. The characterization of RS-SiC based materials was investigated by means of SEM, EDS ~d three point bending test. Based on the mechanical property-microstructure correlation, the high temperature applicability of RS-SiC based materials was discussed.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2005.11a
• /
• pp.87-88
• /
• 2005

Ultra-fine copper powders with particle size about 150 nm were synthesized from copper hydroxide slurry by wet method using hydrazine as reduction agent and several sur factants at below $80^{\circ}C$. The particle size distribution and dispersion of synthesized powders as function of temperature, feeding rate of reduction and especially, sur factants were character ized by XRD, BET, PSA and SEM by this process.

• Journal of Advanced Marine Engineering and Technology
• /
• v.26 no.2
• /
• pp.240-247
• /
• 2002

Recently, a thermal energy storage system has been developed actively fur the purpose of saving energy and reducing the peak electrical demand. Especially, ice slurry is a promising working fluid for low temperature energy storage systems. A flow of ice crystals has a large cooling capacity as a result of the involvement of latent heat. However, there are still problems related to the recrystallization of ice crystals for realizing long term storage and long distance transportation. To find improvements fur this, a method for the creation of ice crystals resistant to recrystallization has been proposed and researched by the use of an antifreeze protein (AFP) solution etc. In the present study, it has been investigated the growth of ice crystal in several kinds of water solution added non-ionic surfactant. The results shows that size of ice crystal was smaller with increasing in added surfactant. And ice crystal was not increased with added surfactant.

• Korean Journal of Air-Conditioning and Refrigeration Engineering
• /
• v.13 no.12
• /
• pp.1236-1244
• /
• 2001

In the present study, the possibility of continuous slurry ice making using flowing water solution in a cooled tube has been investigated. The experiments were carried out at various concentration and velocity of water solution, temperature of cooled tube wall, and control pressure in a tube. As a result, four types of operating conditions, that is super-cooling, continuous ice making, intermittent ice making and ice blockage, were classified. And it was found that the critical condition for the continuous ice making was acquired as a function of these experimental parameters.

• Proceedings of the Korea Association of Crystal Growth Conference
• /
• 1996.06b
• /
• pp.87-107
• /
• 1996

The fine Co powder with an average particle sie of less than 1$\mu\textrm{m}$ was prepared by hydrothermal reduction with hydrogen from Co(OH)2 slurry obtained by mixing the solutons of CoSO4$.$7H2O and NaOH. A method to control pH of the end solution around neutrality was proposed. The reduction rate was found to be a function of pH, temperature, hydrogen pressure and the amount of catalyst.

• Bulletin of the Korean Chemical Society
• /
• v.30 no.3
• /
• pp.683-686
• /
• 2009

Slurry phase reaction of elemental silicon with methanol has been studied in the presence of copper using a small amount of cuprous chloride as an activator in DBT (dibenzyltoluene) at various temperatures from 200 ${^{\circ}C}$ to 320 ${^{\circ}C}$. Trimethoxysilane (1a) with a Si-H unit was obtained as the major product and tetramethoxysilane (1b) as the minor product. The reaction worked well using a 0.5 wt % CuCl as an activator. The optimum temperature for this direct synthesis of 1a was 240 ${^{\circ}C}$. Methoxysilanes were obtained in 95% yield with 81% selectivity to 1a from 85% conversion of elemental silicon.

• Journal of the Korean Ceramic Society
• /
• v.45 no.4
• /
• pp.204-207
• /
• 2008

This paper presents a new process for producing SiC fiber-SiC matrix(SiC/SiC) composites by reaction sintering. The processing strategy for the fabrication of the SiC/SiC composites involves the following: (1) infiltration of the SiC fiber fabric using a slurry consisting of Si and C precursors, (2) stacking the slurry-infiltrated SiC fiber fabric at room temperature, (3) cross-linking the stacked composites, (4) pyrolysis of the stacked composites, and (5) hot-pressing of the pyrolyzed composites. It was possible to obtain dense SiC/SiC composites with relative densities of >96% and a typical flexural strength of ${\sim}400$ MPa.

• Proceedings of the SAREK Conference
• /
• 2006.06a
• /
• pp.1213-1218
• /
• 2006

In this study, a numerical model for a vapor compression refrigeration system using MPCM slurries as a secondary fluid through an evaporator was developed, and the system performance was compared with that using water Generally, the MPCM system showed higher performance than the water system. The COP of the MPCM system was higher by 16.6 to 18.6% than that of the water system at all conditions. The MPCM slurry yields better performance in the aspect of heat transfer and heat transportation comparing to the sensible heat transfer medium such as water.

• Proceedings of the KIEE Conference
• /
• 2006.10a
• /
• pp.7-9
• /
• 2006

$(BaSr)TiO_3$ thick films were prepared by tape casting method using $BaTiO_3$ and $SrTiO_3$ powder slurry in order to investigate dielectric properties and low temperature sintering. Sintering density was $5.7\;g/cm^3$ and the BST sample exhibited the maximum dielectric constant, tunability at temperatures near phase transition point. The dielectric constant was increased and curie temperature was shifted to higher temperature with increasing of annealing temperature.

• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.24 no.4
• /
• pp.589-598
• /
• 2000

A pilot-scale Spray Drying Sorber (SDS) system was set up to evaluate the effect of spray characteristics on the desulfurization yield. The size distribution and the Sauter Mean Diameters of slurry droplets were measured in advance using the optical size measurement system, Malvern 2600. The desulfurization yield of the drying chamber by size was measured for the conditions of inlet gas and spray injection. As a reagent, 10% limestone slurry of $Ca(OH)_2$ was treated with flue gas containing $SO_2$, and the combustion gas analyzer and gas detectors were attached to measure the $SO_2$ concentration. With a flow rate of 144 Nm3/h and a temperature range of $200{\sim}300^{\circ}C$, the experiments were performed for the Stoichiometric Ratio (SR) of 1.0 to 3.0 and droplet mean diameter of 6.5 to $34.3{\mu}m$. In case of smaller spray droplets, the desulfurization efficiency improved due to the increase of total droplet surface area, while the reduction in evaporation time reduced the contact time between the droplets and $SO_2$ gas. In some typical region of droplet diameter, this negative effect, reduction of contact time, became dominant and the desulfurization yield decreases the desulfurization yield in spite of the expansion in absorption area. These results revealed that there exists the optimal size of spray droplets for a given state, which is determined by the compromise between the total surface area of slurry droplets and the evaporation time of droplets. The measurements also indicated that the inlet temperature of flue gas changes the optimal injection condition by varying the driving force for evaporation. The results confirm that the effect of the evaporation time of slurry droplets should be considered in analyzing the desulfurization yield as well as the total surface area, for it is a significant aspect of the correlation with the capabilities of $SO_2$ absorption in wet droplets. In conclusion, the optimal condition of spray can be determined based on these results, which might be applied to design or scale-up of SDS system.