• Journal of Korean Society of Water and Wastewater
• /
• v.18 no.5
• /
• pp.608-618
• /
• 2004

Since polyelectrolytes have been used as conditioners, conventionally only a single polyelectrolyte has been added for sludge conditioning. However, the amount of polyelectrolyte needed for optimal conditioning of sludge is very critical. Overdosing reduces the sludge dewaterbility. In this experimental study, sludge conditioning with single or dual polyelectrolyte was conducted to avoid problems associated with overdosing. Single polyelectrolyte conditioning was conducted by one of cationic, nonionic, and anionic polyelectrolytes. The dual polyelectrolyte conditioning was performed by adding one polyelectrolyte and another one in sequence. The dewaterbility of sludges were measured by SRF(specific resistance to filtration), TTF(time to filter), CST(capillary suction time) respectively. Additionally, parameters such as turbidity, zeta potential, viscosity of conditioned sludges or supematant were measured to evaluate the changed characteristics of sludge by addition of polyelectrolytes. From the experiment results, it was concluded that single polyelectrolyte conditioning had a high probability of overdosing, whereas dual polyelectrolyte conditioning resulted in a better dewaterbility and less chance of overdosing. But, it was also found that dosing sequence in dual conditioning was very important according to the characteristics of sludge. Parameters such as viscosity, turbidity, zeta potential were found to be useful as a means of evaluating sludge dewaterbility.

• Journal of the Korea Organic Resources Recycling Association
• /
• v.22 no.1
• /
• pp.27-34
• /
• 2014

demand for a low-cost treatment technology is high because the sewage sludge has an 80% or higher water content and a high energy consumption cost. This study apply the thermal hydrolysis reaction that consumes a small amount of energy for sludge treatment. The purpose of this study is to quantify the viscosity of sewage sludge according to reaction temperature. we measured continuously the torque of dewatered sludge by the reaction temperature. As the reaction temperature increased, the dewatered sludge is thermal hydrolysis under a high temperature and pressure. Therefore, the bond water in the sludge cells comes out as free water, which changes the dewatered sludge from a solid phase to slurry of a liquid phase. The results of the viscosity measurements according to the reaction temperature showed that the viscosity was very high at $270,180kg/m{\cdot}sec$ at a temperature of 293K, but rapidly decreased with increases in the reaction temperature to $12kg/m{\cdot}sec$ at a temperature of 400K and to $4kg/m{\cdot}sec$ at a temperature of 460K or higher, similar to the changes in the viscosity of water. And we was obtained the viscosity function of boundary condition for the optimal design of thermal hydrolysis reactor by numerical modeling based on the this results.

• Proceedings of KOSOMES biannual meeting
• /
• 2001.10a
• /
• pp.17-24
• /
• 2001

The sludge oils were produced necessarily in the ships operation, so that it will be the best way to manage the sludge oils inside ship itself from a viewpoint of the prevention of marine oil pollution from ship. The present study deal with the ultrasonic breaking systems which recycle the sludge oil from ships into usable oil to be burnt. The first place, experimental studies were carried out to investigate the homogenizing effect of the marine oils by repeated vibration of ultrasonic transducer. Variation of the properties(viscosity, specific gravity and pH) and the matrix structures for the environment of various marine oils were interpreted to analyze the breaking, dispersion effects by cavity. The experimental results can be useful to the development of sludge oil disposing systems.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 1987.11a
• /
• pp.1-27
• /
• 1987

1. Gasoline engine sludge is a major worldwide problem 2. U.S. and European sludge have similarities 3. Stop-go driving and longer oil drains make the problem worse 4. Fuel is a major influencing factor 5. Increased use of cracked components may be cause 6. Sludge can be peproduced in controlled field tests 7. Daimler benz M102E and ford PV-2 (VE) tests have been developed to overcome problem by higher oil quality 8. The M102E and PV-2 respond in a similar way to increased dispersancy 9. High dispersant ocp viscosity modifiers appear to have unique adbantage in both tests

• Membrane and Water Treatment
• /
• v.6 no.6
• /
• pp.501-512
• /
• 2015

A laboratory-scale submerged membrane bioreactor (MBR) was continuously operated for 100 d at an infinite sludge retention time (SRT) with the aim of identifying possible relation between the filterability of mixed liquor and sludge properties, such as extracellular polymeric substances (EPS), soluble microbial products (SMP), viscosity of mixed liquor, zeta potential of flocs and particle size distributions (PSD). Research results confirmed that MBR can operate with a complete sludge retention ensuring good treatment performances for COD and $NH_3-N$. However, the long term operation (about 40 d) of MBR with no sludge discharge had a negative influence on sludge filterability, and an increase in membrane fouling rates with the time was observed. There as a strong correlation between the sludge filterability and the fouling rate. Among the different sludge properties parameters, the concentration SMP and EPS had a more closely correlation with the sludge filterability. The concentrations of SMP, especially SMP with MW above 10 kDa, had a strong direct correlation to the filterability of mixed sludge. The protein fractions in EPS were biodegradable and available for microorganism metabolism after about 60 days, and the carbohydrates in EPS had a significantly negative effect on sludge filterability in MBR at an infinite SRT.

• Microbiology and Biotechnology Letters
• /
• v.23 no.6
• /
• pp.702-709
• /
• 1995

Degradation Of $\kappa $-carrageenan-based film by microorganisms screened from carrageenan source and activated sludge of a carrageenan producing factory was investigated by measuring changes of pH, viscosity, total sugar and total organic carbon (TOC) of the medium containing $\kappa $-carrageenan as a carbon source. Initially fifteen strains of microorganism were isolated from carrageenan source and activated sludge and then three organisms among them were selected based on the ability of growing in the medium including 0.3% $\kappa $-carrageenan as a sole carbon source. They were identified as Escherichia coli, Saccharomyces cerevisiae and Aspergillus niger. As indices of biodegradability Of $\kappa $-carrageenan based film, the changes of pH, viscosity, total sugar, and TOC of the carrageenan film-based medium were tested by the cultivation of single or mixed strains of the identified organisms. Mixed culture showed the highest biodegradability, which resulted in the changes of pH from 6.5 to 3.0, viscosity from 164 cps to 15.6 cps, total sugar content from 2.35 g/l to 0.53 g/l and TOC from 5721 ppm to 232 ppm after 30 days of cultivation. The biodegradability determined as the reduction rate of TOC by pure cultures of Asp. niger, E. coli, Sacch. cerevisiae and mixed culture of the three organisms were 94%, 86%, 80% and 96%, respectively.

• Journal of Korean Society of Environmental Engineers
• /
• v.32 no.4
• /
• pp.341-348
• /
• 2010

The basic principle of fry drying process of sludge lies in the rapid pressure change of sludge material caused by the change of temperature between oil and moisture due to the difference of specific heat. Therefore, the rapid increase of pressure in drying sludge induces the efficient moisture escape through sludge pores toward heating oil media. The object of this study is to carry out a systematic investigation of the influence of various parameters associated with the sludge fry drying processes on the drying efficiency. To this end, a series of parametric experimental investigation has been made together with the numerical calculation in order to obtain typical drying curves as function of important parameters such as drying temperature, sludge diameter, oil type and sludge type. In the aspect of frying temperature, especially it is found that the operation higher than $140^{\circ}C$ was favorable in drying efficiency regardless of type of waste oil employed in this study. The same result was also noted consistently in the investigation of numerical calculation, that is, in that the sludge particle drying was efficiently made over $140^{\circ}C$ irrespective of the change of particle diameter. As expected, in general, the decrease of diameter in sludge was found efficient both experiment and numerical calculation in drying due to the increased surface area per unit volume. In the investigation of oil type and property, the effect of the viscosity of waste oil was found to be more influential in drying performance. In particular, when the oil with high viscosity, a visible time delay was noticed in moisture evaporation especially in the early stage of drying. However, the effect of high viscosity decreased significantly over the temperature of $140^{\circ}C$. There was no visible difference observed in the study of sludge type but the sewage sludge with a slightly better efficiency. The numerical study is considered to be a quite useful tool to assist in experiment with more detailed empirical modeling as further work.

• Journal of the Korean Society of Marine Environment & Safety
• /
• v.5 no.2
• /
• pp.67-78
• /
• 1999

Recently, a greater part of all ship use a coarse heavy fuel oil(HFO) over specific gravity(S.G) 1.00/15$^{\circ}C$ and viscosity 3,500 cSt/4$0^{\circ}C$ as the fuel oil of marine boiler or internal combustion engine from the viewpoint of economical ship' operation. The greater plan to improve a combustion methods of heavy fuel oil, such as atomization, homogeneity and emulsification, were contrived and carried out newly, and then applied 20kHz ultrasonic homogenizer to one of test methods. Also, adopted the marine oils(fuel oil and lubricating oil etc.) and sludge oil as test solutions, and its matrix structures were examined with photographs, Especially, it is important at control system of oil pollution, for the sludge oil emulsified, to be recycled as fuel oil of boiler according to 20kHz Ultrasonic homozenizer, and then fuel saving is attained effectively by making sludge oil to be burnt.

• Journal of Korean Society on Water Environment
• /
• v.27 no.1
• /
• pp.44-53
• /
• 2011

Membrane bio-reactor (MBR) has several advantages over the conventional activated sludge process, including a high biomass, low sludge production, and better permeate quality. Therefore, the MBR have gained popularity for municipal and industrial wastewater treatment. However the MBR usually were used for sewage and low streng th wastewater treatment because of membrane fouling problem and limitation of oxygen transfer into biomass. In this study, the hybrid process combining MBR and pure oxygen was tested for high strength organic wastewater treatment in the COD loading range from 2 to $10kgCOD/m^3{\cdot}day$. The hybrid process, membrane coupled pure oxygen high compact reactor (MPHCR), had been operated for one year and operation parameters, the effect of COD loading, MLSS concentration and the location of membrane module were studied for membrane fouling characteristic. Also membrane resistance test and the component of foulant was analyzed to investigate what is specific foulant in the MBR.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.3 no.2
• /
• pp.152-158
• /
• 2015

In order to investigate the feasibility of stone dust sludge as fine aggregate, an experimental study was performed on cement mortar with stone dust sludge. fresh mortar properties and strength with various stone dust sludge replacement ratios were estimated. the replacement ratio adopted in this study was 0, 10, 20, 30%. Flow, air content, and rheological properties were considered as properties of fresh mortar. Compressive strength and flexural tensile strength were measured for strength. The results are as follows. Higher amount of stone dust sludge caused reduction in slump and air content. In the rheological properties, both yield stress and plastic viscosity increased as stone dust sludge content increased up to 20% replacement ratio, but there were no remarkable difference between 20 and 30%. Yield stress increased drastically between 10 and 20%. Compressive and flexural tensile strength results indicated that the strength variation was not significant according to stone dust sludge content, but the strength gain in the early age by adding stone dust sludge was evident. the strength at the age of 28 days however did not show noticeable effect of adding stone dust sludge.