• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.20 no.5
• /
• pp.202-206
• /
• 2010

Single crystals of $ZnWO_4$ were grown successfully in the [100], [010] and [001] directions using the Czochralski method. The growth parameters and the formation of slip plane in $ZnWO_4$ crystals were studied. $ZnWO_4$ crystals had a cleavage plane of (010). The dislocation density on the (010) plane at the center of the crystal was lower than that of the edge region. It was inferred that the high density at the edge of the crystals was caused by the thermal gradient during crystal growth. The etch pit arrangement revealed the (100) slip plane to be most active during crystal growth.

• Korean Journal of Materials Research
• /
• v.27 no.12
• /
• pp.679-687
• /
• 2017

A strain-gradient crystal plasticity finite element method(SGCP-FEM) was utilized to simulate the compressive deformation behaviors of single-slip, (111)[$10{\bar{1}}$], oriented FCC single-crystal micro-pillars with two different slip-plane inclination angles, $36.3^{\circ}$ and $48.7^{\circ}$, and the simulation results were compared with those from conventional crystal plasticity finite element method(CP-FEM) simulations. For the low slip-plane inclination angle, a macroscopic diagonal shear band formed along the primary slip direction in both the CP- and SGCP-FEM simulations. However, this shear deformation was limited in the SGCP-FEM, mainly due to the increased slip resistance caused by local strain gradients, which also resulted in strain hardening in the simulated flow curves. The development of a secondly active slip system was altered in the SGCP-FEM, compared to the CP-FEM, for the low slip-plane inclination angle. The shear deformation controlled by the SGCP-FEM reduced the overall crystal rotation of the micro-pillar and limited the evolution of the primary slip system, even at 10 % compression.

• Journal of Mechanical Science and Technology
• /
• v.19 no.4
• /
• pp.985-992
• /
• 2005

Vehicle Stability Control (VSC) system prevents vehicle from spinning or drifting out mainly by braking intervention. Although a control threshold of conventional VSC is designed by vehicle characteristics and centered on average drivers, it can be a redundancy to expert drivers in critical driving conditions. In this study, a manual adaptation of VSC is investigated by changing the control threshold. A control threshold can be determined by phase plane analysis of side slip angle and angular velocity which is established with various vehicle speeds and steering angles. Since vehicle side slip angle is impossible to be obtained by commercially available sensors, a side slip angle is designed and evaluated with test results. By using the estimated value, phase plane analysis is applied to determine control threshold. To evaluate an effect of control threshold, we applied a 23-DOF vehicle nonlinear model with a vehicle planar motion model based sliding controller. Controller gains are tuned as the control threshold changed. A VSC with various control thresholds makes VSC more flexible with respect to individual driver characteristics.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.10 no.4
• /
• pp.337-343
• /
• 2000

Prism plane slip {11$\bar{2}$0}1/3{$\bar{1}$120} location velocity in sapphire ($\alpha$-Al$_2$O$_3$) single crystals was measured by etch-pit method. The dislocation velocities were measured as a function of temperature and stress between $1150^{\circ}C$ and $1400^{\circ}C$ for engineering stresses in the range 140 to 250 MPa. The dependence of temperature and stress in dislocation velocity was investigated. The activation energy for dislocation velocity was determined to be 4.2$\pm$0.4 eV. On the other hand, the stress exponent (m) describing the stress dependence of dislocation velocities was in the range of 4.5$\pm$0.8. Through this experiments, it was reconfirmed that the basal plane in sapphire single crystals has the 3-fold symmetry.

• Journal of the Korean earth science society
• /
• v.29 no.5
• /
• pp.437-445
• /
• 2008

We analyzed fault plane solutions of the recent twenty-two earthquakes which occurred from 2004 to 2006 in the central part of the Korean Peninsula by using P- and S-wave polarities along with SH/P amplitude ratios. The fault plane solution shows that strike-slip fault is dominant here, especially for the events with local magnitude equal to or greater than 3.0. However, some events with local magnitude less than 3.0 show normal fault or strike-slip fault with normal components. In the case of strike-slip fault, its orientation is almost in the direction of NNE-SSW to NE-SW almost parallel to the general trend of faults, while the compressional axis of the stress field trends ENE to E-W. The result is almost consistent with the stress field in and around the Korean peninsula, as reported previously. We cannot give any appropriate explanations to the normal faulting events along the western offshore and inland areas whether it is related to the local stress changes or tectonically unidentified extensional structures. Thus, an extension of investigations is desirable to clarify the cause of such phenomena.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.37 no.4
• /
• pp.399-405
• /
• 2009

The focal plane image stabilization for a satellite camera is one of the an effective method which can increase the satellite camera's image quality by removing the motion disturbance of a focal plane. The objectives of this article are to introduce the concept of the focal plane image stabilization and determine the best driving conditions of the actuator for the response and thrust. Under various driving condition the experiments have been performed to investigate the response and thrust characteristics of the piezoelectric driven stick-slip actuator of the focal plane image stabilizing device. From experiments, the best driving frequency and duty ratio for the magnesium slider are 70 kHz and 27%, respectively.

• Journal of the Korean Society for Heat Treatment
• /
• v.22 no.1
• /
• pp.8-15
• /
• 2009

Structural studies have been performed on precipitation hardening found in $Ni_{3}Al$ based ordered alloys using transmission electron microscopy (TEM). Tilt experiments by the weak-beam method were made to obtain some information concerning the cross slip mechanism of the superlattice dislocation. The strength of ${\gamma}'-Ni_3$(Al,Ti) increases over the temperature range of experiment by the precipitation of fine $\gamma$ particles. The peak temperature where a maximum strength was obtained shifted to higher temperature. Over the whole temperature range, the interaction between dislocation and $\gamma$ precipitates is attractive. On the temperature range of 773 K to 973 K, the dislocations in ${\gamma}'$ matrix move on (111) primary slip plane. When the applied stress is removed, the dislocations make cross slip into (010) plane, while those in $\gamma$ precipitates remain on the (111) primary slip plane. The increase of high temperature strength in ${\gamma}'-Ni_3$(Al,Ti) containing $\gamma$ precipitates is due to the restraint of cross slip of dislocations from (111) to (010) by the dispersion of disordered $\gamma$ particles.

• Journal of Magnetics
• /
• v.16 no.3
• /
• pp.220-224
• /
• 2011

Die-upset magnets from a mechanically-milled Pr(Co,In)$_5$-type alloy are known to have a peculiar texture; the easy magnetization axis (c-axis) is perpendicular to the pressing direction. This peculiar texture is thought to be linked closely to the anisotropic mechanical properties of Pr(Co,In)$_5$-type hexagonal compounds. The hardness of the Pr(Co,In)$_5$-type crystal was measured using selectively grown grains in an annealed $Pr_{17}Co_{82}In_1$ alloy button, and the crystallographic orientation was determined by observing the magnetic domain image. The hardness (549 VHN) on the plane with a 'cogwheel'-type domain image was significantly higher than that (510 VHN) on the plane with a 'cigar'-type domain image, indicating that the inter-layer bonding force between the (000l) basal planes is stronger than that between the (hki0) planes. This suggests that the most probable slip plane is the (hki0) plane parallel to the c-axis. During die-upsetting of the Pr(Co,In)$_5$-type alloys the deformation proceeds by (hki0) plane slip, and the c-axis rotates to ultimately become oriented perpendicular to the pressing direction. It is proposed that the peculiar texture in the die-upset Pr(Co,In)$_5$-type magnets is probably developed by slip deformation of the (hki0) plane of the Pr(Co,In)$_5$-type grains.

• Journal of Korean Society of Steel Construction
• /
• v.8 no.3 s.28
• /
• pp.97-105
• /
• 1996

A Stochastic line source model is developed to simulate the seismic wave field generated during the rupture propagation process along a fault plane of which length is much larger than its width. The fault plane is assumed to consist of randomly distributed slip zones and barriers and each slip zone is modeled as a point source. By combining the newly developed source model with wave propagation analysis method in a layered 3-D visco-elastic half space, synthetic seismograms are obtained. The calculated accelerograms due to vertical dip slip and strike slip line sources are presented.

• The KSFM Journal of Fluid Machinery
• /
• v.2 no.3 s.4
• /
• pp.17-23
• /
• 1999

In the present numerical analysis, investigation of the effect of blade loadings from design shape on the slip factor variation was studied. Both the Eckardt radial bladed impeller and the backswept impeller were analyzed. In addition, a new design of the blade profile was arbitrarily attempted to generate a center-loading pattern in the original backswept impeller. Three dimensional compressible Navier-Stokes flow analysis with the Baldwin-Lomax turbulence model was applied to get the numerical slip factor at each impeller exit plane using the mass-averaging technique. The numerical slip (actors are in good agreement with the experimental ones and the Wiesner's slip factors deviate further from the numerical and experimental ones in both backswept impellers. Deviation angles and meridional channel loadings are found in no relation with the trend of change of the slip factor. Blade-to-blade loadings in midspan location are, however, found to have a direct relationship, especially at the sections where maximum loadings we to be expected. That information can be utilized in establishing an improved expression for slip factors in the future.