• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2006년도 춘계학술대회 논문집
• /
• pp.149-152
• /
• 2006

Dry sliding wear behavior of low carbon dual phase steel, of which microstructure consists of hard martensite in a ductile ferrite matrix, has been investigated. The wear characteristics of the dual phase steel was compared with that of a plain carbon steel which was normalized at $950^{\circ}C$ for 30min and then air-cooled. Dry sliding wear tests were carried out using a pin-on-disk type tester at various loads of 1N to 10N under a constant sliding speed condition of 0.2m/sec against an AISI 52100 bearing steel ball at room temperature. The sliding distance was fixed as 1000m for all wear tests. The wear rate was calculated by dividing the weight loss measured to the accuracy of $10^{-5}g$ by the specific gravity and sliding distance. The worn surfaces and wear debris were analyzed by SEM, EDS and a profilomter. Micro vickers hardness values of the cross section of worn surface were measured to analyze strain hardening behavior underneath the wearing surfaces. The were rate of the dual phase steel was lower than the plain carbon steel. Oxidation on the sliding surface and strain hardening were attributed for the higher wear resistance of the dual phase steel.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2004년도 ICCAS
• /
• pp.227-231
• /
• 2004

In this paper, a robust Sliding Mode Variable Structure (SMVS) controller is designed for Active Queue Management (AQM). This type of controller is insensitive to noise and variance of the parameters, thus it is suitable to time varying network systems. Simulation results conform the robust performance of SMVS controller against the disturbance. At the same time, a complete comparison between SMVS and PI controllers is made. The conclusion is that both transient and steady state performance of SMVS controller is better than that of PI one.

• 대한전자공학회:학술대회논문집
• /
• 대한전자공학회 1999년도 하계종합학술대회 논문집
• /
• pp.1125-1128
• /
• 1999

This paper presents a speed controller for the Sinusoidal type BLDC motor using the sliding mode. Since the sliding mode control has some practical limitations such as the chattering phenomenon and reaching phase problems, the technique of overcoming these limitations is proposed in a practical realization. This proposed speed control technique is composed of an smooth integral variable structure control(IVSC), and chattering prediction method.

• 제어로봇시스템학회:학술대회논문집
• /
• 제어로봇시스템학회 2001년도 ICCAS
• /
• pp.42.2-42
• /
• 2001

This paper deals with a fuzzy sliding mode observer for nonlinear systems. A nonlinear system is approximated by a multiple model Takagi Sugeno fuzzy system and then transformed into a canonical form for which a nonlinear observer is constructed. This study presents a type of fuzzy sliding mode observer that deals with matched and unmatched uncertainties in the plant dynamics very effectively. The proposed method was validated by the example of a inverted pendulum.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2002년도 학술대회지
• /
• pp.573-576
• /
• 2002

A flow characteristics of automotive oil pump of gerotor type has been investigated numerically. For the simulation of gerotor that have different rotating velocity at inner rotor and outer rotor, node expansion and contraction method was adopted. ASI (Arbitrary Sliding Interfaces) method was also applied at interface between rotating gerotor and stationary volute. The present results showed good agreement with the experimental data.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2011년도 정기총회 및 추계학술대회 논문집
• /
• pp.1478-1485
• /
• 2011

이 기술은 지하철 역사 특성상 천정판 개방이 수반되는 보수공사와 각종점검이 수시로 이루어지고 있는 바, 잦은 탈 부착으로 천정판이 쉽게 탈락 및 훼손되어 역사 유지관리에 어려움이 발생되고 있는 문제를 해결하기 위해 천정판의 설치 방법을 고정방식에서 탈피하여, 일부분을 미닫이 방식으로 개폐할 수 있도록 설치함으로서 천정판의 탈 부착으로 인한 훼손을 방지하고 내구성을 증대시켜 역사 천정판 교체공사 주기를 연장시키고 이에 따른 유지관리 비용 절감 효과가 있는 천정판 시공방법을 제시코자 함.

• 대한기계학회논문집
• /
• 제19권1호
• /
• pp.99-110
• /
• 1995

An industrial robot needs a simple and robust control algorithm obtaining high precision control performance in spite of disturbance and parameter's change. In this paper, for solving this problem, a new sliding mode control algorithm is proposed and applied to the trajectory control of a SCARA type robot. The proposed algorithm has diminished the chattering occurring in sliding mode by setting a dead band along the switching line on the phase plane. It shows that we can easily obtain a simple switching control input satisfying sliding mode in spite of regarding nonlinear terms of a manipulator and servo system as disturbance. A guideline for selection of dead-band width is determined by optimal value of cost function presenting magnitudes of chattering and error. By this algorithm, we can expect the high performance of the trajectory tracking of an industrial robot which needs a robust and simple algorithm.

• Tribology and Lubricants
• /
• 제12권1호
• /
• pp.22-28
• /
• 1996

This study was undertaken to investigate the dry wear characteristics and mechanism of KP-4M steel for plastic molding against SKD 61 hardened by heat treatment. The wear test was carried out under different conditions such as sliding speed, contact pressure, sliding distance, with frictional tester of pin on disc type. The wear loss on variation of sliding speed was little in lower speed range below 0.5 m/sec and in higher speed range above 1.5 m/sec,'but wear loss was high in intermediate speed range. The critical sliding speed, which showed the maximum value of specific wear rate, became lower with increased contact pressure. Increasing the contact pressure, the critical sliding distance Lcr which the wear mechanism changes from severe wear to mild wear was increased due to the decrease of oxidation reaction velocity. Through this study we suggested a model of generation and elimination process of wear debris of KP-4M steel for plastic molding.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2000년도 춘계학술대회논문집
• /
• pp.21-25
• /
• 2000

An inverse finite element approach is employed for more capability to design the optimum blank shape from the desired final shape with small amount of expense and computation time For multi-stage sheet metal forming processes numerical analysis is expense difficult to carry out the to its complexities and convergence problem. It also requires lots of computation time. For the analysis of elliptic cup with large aspect ratio intermediate sliding constraint surfaces are difficult to describe. in this paper multi-stage finite element inverse analysis is applied to multi-stage elliptic cup drawing processes to calculate intermediate blank shapes and strain distributions in each stages. To describe intermediate sliding constraint surfaces an analytic scheme is introduced to deal with merged-arc type sliding surfaces.

• Transactions on Control, Automation and Systems Engineering
• /
• 제4권4호
• /
• pp.296-304
• /
• 2002

A position tracking control schemes on the precise mechanical system in presence of nonlinear dynamic friction is proposed. A nonlinear dynamic friction is regarded as the bristle friction model to compensate effects of friction. The conventional sliding mode controller often has been used as a non-model-based friction controller, but it has a poor tracking performance in high-precision position tracking application since it completely cannot compensate the friction effect below a certain precision level. Thus to improve the precise position tracking performance, we propose the sliding mode control method combined with the friction-model-based observer having tunable structure of the transient response. Then this control scheme has a good transient response as well as the high precise tracking performance compared with the conventional sliding mode control without observer and the control system with similar type of observer. The experiments on the bali-screw drive table with the nonlinear dynamic friction show the feasibility of the proposed control scheme.