• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.05a
• /
• pp.833-836
• /
• 2007

Load/Unload technology has more benefits than the conventional CSS technology. However, it remains unsolved technical problem on the unloading process. While the slider climbs up the ramp at the outer edge of the disk, the possibility of the slider-disk contact by lift-off force and rebound of the slider increases. This paper focuses on no slider-disk contact. To prevent the slider-disk contact, we apply the disk bump on disk outer edge proceeding unload. Firstly, in the simulation, the bump dimension is determined by changing bump design parameters. Secondly, dynamic stability of slider have to be checked on disk bump before unload analysis, and unload analysis is performed by applying stable bump shapes to unload simulation. Thirdly, we select optimal bump shape to improve unload performance by unload analysis. Finally, in the experiment, the disk bump is mechanically manufactured by pressing disk surface using diamond tip. That is variously processed by changing pressing pressure. After confirming bump shape by nano-scanner, proper bump shape is applied to real experimental unload process. Through this investigation, we propose the optimal bump design to prevent the slider-disk contact, and then we can realize improved unloading performance.

• Transactions of the Society of Information Storage Systems
• /
• v.7 no.2
• /
• pp.65-69
• /
• 2011

Head Disk Interface (HDI) in a Hard Disk Drive (HDD) has decreased to achieve high areal density. Thus, the contact between a slider and a disk becomes more important. The contact between the slider and the disk can cause severe wear and damage of both the slider and the disk. Especially, Touch Down (TD) that the contact occurs continuously and repeatedly is extremely dangerous. Therefore, it is necessary to analyze the unstable bouncing vibration of the slider in head-disk interface. In this paper, we investigate the characteristic and causes of the Touch Down.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2007.11a
• /
• pp.1276-1279
• /
• 2007

The main objectives of the Load/Unload are no slider-disk contact and no media damage. But, it remains unsolved technical problems on the unloading process. While the slider climbs up the ramp at the outer edge of the disk, the possibility of the slider-disk contact by lift-off force and rebound of the slider increases. Keeping in mind of these points, to prevent the slider-disk contact, we apply the disk bump on disk outer edge proceeding unload. First, referring to the simulation results, we select the optimal bump shapes to improve unload performance by unload analysis. Second, the disk bump is mechanically manufactured by pressing disk surface using tungsten tips. The bumps are variously processed by changing pressing pressure of tungsten tips. After confirming bump shape by nano-scanner, the optimal bump shape is applied to experimental unload process. Through this experiment, it is conformed that the unload performance was improved by using the optimal disk bump to prevent the slider-disk contact.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2002.05a
• /
• pp.160-165
• /
• 2002

The flying height of contact slider is determined by vertical and pitching motions. This paper performed the computer simulation for flying height change of contact slider. It is changed by many parameters, contact stiffness. contact damping, all bearing stiffness ratio and so on. So computer simulation analysis is performed for knowing for what change of these parameters influences in flying height of contact slider. The practical recording zone surface is gotten by using SPM. In recording zone, flying height is simulated for each parameter. the settling time which the flying height of contact slider is lower than 10nm is analyzed over practical disk surface for changing each parameter. Through these results, the contact slider can be analyzed for more accuracy dynamic characteristics.

• Transactions of the Society of Information Storage Systems
• /
• v.3 no.2
• /
• pp.81-85
• /
• 2007

Reliability of a hard disk drive depends on the head disk interface (HDI) characteristics. Particularly, the disk media and the head can be damaged due to contact between the two components during operation. The contact may occur due to particles being introduced into the disk/slider interface or due to direct contact between the slider and the disk. Such contacts may be induced by external vibration or abnormal operation of the HDI. In this work the characteristics of scratches generated on the disk surface were investigated. The scratches were generated by impacting the hard disk. The type of scratches was analyzed with respect to their shape and dimensions.

• Transactions of the Society of Information Storage Systems
• /
• v.11 no.1
• /
• pp.11-15
• /
• 2015

In HDD industry, many technologies have been developed and investigated as means to increase the areal density of drives. Thermal flying-height control has been considered and widely applied in current HDD. When contact occur between TFC slider and disk, the slider has a friction heating induced by highly rotated disk. Moreover, because of the friction heating, additional protrusion of slider can occur. The additional protrusion in contact situation can be a severe effect on head part of slider and disk. Therefore, in this paper, we analyze the friction heating and additional protrusion in contact situation.

• Tribology and Lubricants
• /
• v.17 no.4
• /
• pp.312-320
• /
• 2001

In magnetic hard disk drives, higher areal recording density requires reduction of head-disk spacing. To overcome the increase of stiction associated with reduction of head-disk spacing, a padder slider, which adds pads to slider's air bearing surface, can be one of the practical solution for sub 20 nm flying height, and even for near contact recording. This study investigated the tribological characteristics of a padder slider. A padder slider took off slowly but showed less friction force than a normal slider. The hot/dry CSS test and drag test indicated that pad wear of a padder slider was negligible. The tribological performance of disk is an important factor to be considered. In particular, less carbon overcoat layer of the disk will result in higher stiction and wear in slider/disk interface. In conclusion, a padder slider shows encouraging tribological performances for practical use in HDD.

• Transactions of the Society of Information Storage Systems
• /
• v.2 no.3
• /
• pp.184-188
• /
• 2006

In recent years the flying height of the head/slider has been decreasing in order to increase the recording density of hard disk drive (HDD). Accordingly, it was predicted that direct contact between slider and disk surface (slider slap) can cause defects on the disk such as scratch and particle generation. In this work, we theoretically demonstrate the effect of rounded-edge slider using Hertzian contact theory. Depth and width of scratch were predicted by plowing model. Furthermore, as we fabricated rounded-edge slider, rounded-edge slider was tested and compared with sharp-edge slider. The experimental results show rounded-edge was effective for reducing scratch depth.

• Tribology and Lubricants
• /
• v.22 no.2
• /
• pp.59-65
• /
• 2006

In hard disk drives as the head to disk spacing continues to decrease to facilitate recording densities, slider disk interactions have become much more severe due to direct contact of head and disk surfaces in both start/stop and flying cases. The slider disk interaction in CSS (contact-start-stop) mode is an important source of particle generation and tribocharge build-up. The tribocharge build-up in the slider disk interface can cause ESD (electrostatic discharge) damage. In turn, ESD can cause severe melting damage to MR or GMR heads. The spindle speed of typical hard disk drives has increased in recent years from 5400 rpm to 15000 rpm and even higher speeds are anticipated in the near future. And the increasing disk velocity leads to increasing disk acceleration and this might affect the tribocharging phenomena of the slider/disk interface. We investigated the tribocurrent/voltage build-up generated in HDD, operating at increasing disk accelerations. In addition, we examined the effects with relative humidity conditions and rest time. We found that the tribocurrent/voltage was generated during pico-slider/disk interaction and its level was about $3\sim16pA$ and $0.1\sim0.3V$, respectively. Tribocurrent/voltage build-up was reduced with increasing disk acceleration. Higher humidity conditions $(75\sim80%)$ produced lower levels tribovoltage/current. Therefore, a higher tribocharge is expected at a lower disk acceleration and lower relative humidity condition. Rest time affected the charge build-up at the slider-disk interface. The degree of tribocharge build-up increased with increasing rest time.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2006.11a
• /
• pp.140-143
• /
• 2006

Load/Unload(L/UL) technology includes the benefits, that is, increased areal density, reduced power consumption and improved shock resistance. The main issues of L/UL are no slider-disk contact and no media damage. To make sure L/UL stability, we consider many design parameters in L/UL systems. This paper is focused on disk design parameters through designing a disk bump in outer guard band(OGB). In the case of bump design on the disk, we create a bump by changing bump design parameters as like size and amplitude. From dynamic analysis, we choose optimal bump model with the highest flying height and the longest rising time. When a slider passes over a bump in dynamic system, the slider rise above bump according to bump shape. On the basis of this rising effect on the bump, we apply bump design to classical L/UL system having slider-disk contact possibility. This study is based on the simulation, we finally realize improved slider unloading performance by applying slider dynamic result on unload simulation.