• KIEAE Journal
• /
• 제7권5호
• /
• pp.143-148
• /
• 2007

The application of metal deck floor system is increasing gradually and especially for office buildings. In the cases of large parking structures and storage structures, the construction period and the cost can be reduced. Also the steel deck system can prevent the crack of a floor and reduce the retrofit expenses. However, the floor should stand for the repeated truck load which is relatively heavier repeated loading. The mechanical behavior of a slab under repeated load is also different from the static loading state. An evaluation of a structural capacity was performed in this study through the dynamic capacity evaluation experiment for an application of a composite deck floor system as a parking structure slab. The period of repeated loadings were set up as 25years and 960,000 times monotone cyclic loads were applied at the center of the specimens. The tension crack propagation and patterns at the center of specimens were examined.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2014년도 춘계 학술논문 발표대회
• /
• pp.70-71
• /
• 2014

The structural work is the main process of building construction which influence on the time, cost, safety and quality. The form work is one of the main process which has from 20 to 30 percentage of structural work. Especially the form work for beams is complex and need more manpower compared with form work for column or slab. When the existing forms such as plywood form, steel framed wooden form and aluminum form, is used for form work of beam, it would result in the cost overrun caused by needs of lots of manpower and resources. Therefore, the aim of this study is analysis of the requirement for development of SMART beam form. The result of this study shall be used for the development of SMART form work system.

• Bulletin of the Korean Chemical Society
• /
• 제17권4호
• /
• pp.324-330
• /
• 1996

We examined the formal oxidation states of Pb and Cu in the Pb2CuO4 slab of Pb2Sr2ACu3O8(A=Y1-xCaxor Nd1-xSrx) and their possible changes by oxygen incorporation in the Cu layer of the slab by performing tight-binding band electronic structure calculations on the Pb2CuO4+δ slab. Our results show that the most likely oxidation state of Pb is +2 and that of Cu is +1 for the Pb2CuO4 slab prior to oxidation. With small δ values, the oxygen incorporation occurs by the formation of such chain fragments as in YBa2Cu3O7-y along the a+b axis. The four-coordinate Cu atoms in the chain fragments are in the +3 oxidation states. For values of δ larger than 0.5, however, an additional oxygen (Oad) goes to the site along the b axis to form short Pb-Oad distances oxidizing Pb2+ to Pb4+. This change in the Pb oxidation state leads to the suppression of superconductivity due to the decrease of holes in the CuO2 layer.

• Computers and Concrete
• /
• 제22권5호
• /
• pp.481-492
• /
• 2018

In this paper, a new hybrid fiber system (NHFS) is investigated for the application of slab. The steel fiber, polyvinyl alcohol (PVA) fiber and calcium carbonate ($CaCO_3$) whisker is added to form NHFS. The four-point bending test is carried out on the flexural properties of slab with plain, steel fiber, traditional hybrid fiber system (THFS) and NHFS reinforced cementitious composites. The flexural behavior is evaluated by ASTM C1018-97, JCI-SF4 and post-crack strength (PCS) technique. The evaluation parameters of flexural toughness such as toughness index (TI), equivalent flexural strength (EFS) and PCS are determined. The size of slab specimens is $15mm(thickness){\times}50mm(width){\times}200mm(length)$. The results show that adding $CaCO_3$ whisker to THFS can significantly improve the flexural strength, TI, EFS, PCS of the slab. The empirical relation between reinforcing index ($RI_v$) and flexural parameters show that flexural parameters of slabs increase first and then decrease; which indicates that optimum $RI_v$ values can be helpful in the considering the mix design of steel-PVA fibers-$CaCO_3$ whisker composites for achieving the desired flexural-related properties. The scanning electron microscopy is performed to observe the micro-morphological characteristics of the fracture surface, which proved the positive hybrid effect among the different fibers in cementitious composites. The NHFS can arrest the generation and propagation of the crack from micro to macro level.

• 한국건축시공학회지
• /
• 제21권4호
• /
• pp.293-303
• /
• 2021

국내 PC공장은 PC 유공 슬래브를 생산하기 위해 자동화 설비를 도입하거나 매입물 삽입을 통해 중공 단면을 구현하지만 PC공장의 과다한 초기투자비용이 생산원가의 증가라는 주요 원인으로 작용하기에 다른 대안이 필요한 상황이다. 따라서 본 연구에서는 PC 유공 슬래브 부재 생산시 고무 튜브를 내부 속빈 공간을 형성하는 거푸집으로 사용함으로써 다양한 중공 형상의 성형 및 대단면화, 초경량화, 신속생산 대응 가능을 통한 생산성 확보에 기여하고자 한다.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2021년도 가을 학술논문 발표대회
• /
• pp.14-15
• /
• 2021

Even though the Al. form system, which was developed to replace the Euro-form, has been used as the slab lower formwork for almost all concrete structures based on the light weight and high conversion rate, the low-noise Drop method has been developed and used in order to overcome the limitations of the Al. Form system such as noise pollution and safety accidents caused by free fall during the demolding. However, as the low-noise drop method is still insufficient, Safety Full Drop Al. Form method is expected to be in the spotlight in the construction market based on its excellent advantages compared to the developed methods. In addition, we plan to conduct research to further contribute to securing the quality of the overall structure through continuous improvement and supplementation by introducing an automation system to the very construction method.

• 한국건축시공학회:학술대회논문집
• /
• 한국건축시공학회 2011년도 추계 학술논문 발표대회
• /
• pp.35-36
• /
• 2011

Recently, an irregular-shaped super tall building has been increased, aiming toward landmarks of cityscape. However, the complex floor plan derived from an irregular shape requires considerable resources including time, cost, and effort to meet complex structural framework. Based on the motivation, the study proposes a table-form system that is variable slab form appropriate to an irregular shaped floor through improving limitations of an existing table-form system. The variable table-form is expected to reduce construction resources and improve constructability on an irregular floor plan of super tall buildings as well.

• 한국디지털건축인테리어학회논문집
• /
• 제10권1호
• /
• pp.49-56
• /
• 2010

The purpose of this study is to examine the relationship between the structural system used in modern architecture and the form and spatial composition of the buildings. The principle in stabilization of structures is closely related to the architectural form. That is, in order to stabilize a building, a special type of structural system is required and consequently shows up with consistent characteristics in the architectural form. Modern architecture can be classified into skeleton structure, trusses structure, and space structure according to the structural characteristics. Skeleton structure is then divided into a perpendicular form and tapered form. Trusses structure is categorized as dome-shaped structure and slab-shaped structure, and space structure can be divided into compressible space structure and tensile space structure. When classifies the modern building with the aspect of architectural effect, there is a possibility of trying to divide with effect of production, and its expression. Effect of production mean structural system and effect of expression mean space and plan.

• 콘크리트학회논문집
• /
• 제13권2호
• /
• pp.99-106
• /
• 2001

이 연구의 목적은 기존의 단순지지로 더블티 슬래브에 발생하는 과도한 모멘트, 슬래브 깊이, 중앙부 처짐, 단부 균열의 발생 원인을 근원적으로 해결할 연속화된 개량조인트를 개발하는데 그 초점을 두었다. 개량조인트는 다음과 같은 장점을 얻을 수 있다. 먼저, 보중앙 정모멘트의 감소로 인하여 적용하중에 대한 설계스팬을 증가시킬 수 있으며, 슬래브의 처짐을 감소시킬 수 있다. 또한, 기존 더블티공법의 문제점인 더블티와 역티사이의 연결부 균열을 감소시킬 수 있으며, 시공시 부가적인 거푸집을 필요로 하지 않는다. 개선된 더블티의 댑단부와 직사각형보를 연결부 시험체를 활용하여, 길이철근 배근량을 변수로한 정적 3점재하 실험에서 전단력과 모멘트에 대한 거동을 평가하였다. 이 연구의 범위 안에서 다음과 같은 결론을 얻을 수 있다. 개량댑에 의한 연결 부의 연속화는 토핑 콘크리트에 길이 방향 철근을 배근함으로써 효과적으로 구할 수 있으며, 더블티 슬래브의 스팬용량을 증 가시키고 처짐을 일반적으로 감소시킨다. 아울러, 개량댑의 연속화는 단순지지 연결부보다 초기균열에 효과적인 것으로 나타났다.

• 한국콘크리트학회:학술대회논문집
• /
• 한국콘크리트학회 1997년도 가을 학술발표회 논문집
• /
• pp.761-768
• /
• 1997

Recently, on account of the lack of skilled labor and the increase of labor costs, it has been more difficult the construction environment. Now new methods were developed and used many places. This study is concerning the structural performance of Composite Form Panel Method-one of the new methods-of the wall type. It is available to make monolithic system of bearing wall and half slab. This paper presented design and product data by experiments.