• Journal of Bio-Environment Control
• /
• v.22 no.4
• /
• pp.355-360
• /
• 2013

Diesel-burning air heater (air heater) and infrared heating lamp (infrared heater) were installed as auxiliary heaters in two single water-curtained plastic greenhouses with a set night temperature of $6^{\circ}C$ for cultivation of strawberry 'Seolhyang'. The average night air temperature was $6.6^{\circ}C$ in the infrared heater treatment and $7.1^{\circ}C$ in the air heater treatment. However, when the minimum outside temperature fell below $-10^{\circ}C$, the air heater had less internal temperature fluctuations. In contrast, the infrared heater had some cases of falling below the set temperature. The relative humidity was higher than 98% by the side-effect of water-curtain system regardless of the heating system. There was about $5^{\circ}C$ difference in leaf temperature between the turned-on and -off state of the infrared heater, and the efficacy of the infrared heater on leaf temperature was only limited to about 4 meters from the system. Peduncle length and plant height in the infrared heater tended to be greater than those in the air heater. There was, however, no statistically difference in leaf size and numbers of leaves, flowers on first cluster and branches. There was no difference in soluble solids content, fruit firmness, average fruit weight of the harvested fruits, and the yield. Comparing the heating costs, the air heater system took 622,662 won based on 543 L tax-free diesel, while the infrared heater system took 235,284 won by consuming 5,685 kWh of electricity, and 62.2% heating costs saving was achieved.

• Journal of Bio-Environment Control
• /
• v.27 no.2
• /
• pp.180-184
• /
• 2018

This study was conducted to examine the effect OTR film type on the quality of garden cress (Lepidium sativum L.) baby leaf during MA storage. Garden cress harvested at baby leaf size of 10cm plant height packed with 1,300 cc, 10,000 cc, 20,000 cc, 40,000 cc, and $80,000cc{\cdot}m^{-2}{\cdot}day^{-1}{\cdot}atm^{-1}$ OTR (oxygen transmission rate) films and MP (micro-perforated) film, and then stored at $8^{\circ}C$ for 10 days. All of the OTR film treatments showed a decrease of 0.5% fresh weight until the storage end date and a 1.3% decrease in the MP film treatment. The oxygen concentration in the packaging during storage was maintained at 18% or more in 20,000 cc, 40,000 cc, and 80,000 cc OTR film treatments, while the 1,300 cc OTR film treatment decreased to 11% at the storage end date. And the concentration of carbon dioxide was steadily increased in the 1,300 cc and 10,000 cc OTR film treatments to show the levels of 4.5% and 3.4%, respectively, and the other OTR film treatments showed a concentration of less than 1%. Ethylene concentration in the package was maintained at the highest level of $3-5{\mu}L{\cdot}L^{-1}$ in the 1,300 cc treatment during the storage period. The lowest odor and the highest quality of appearance were observed in the 1,300 cc treatment, but the MP film treatment and the other OTR treatments lost marketable quality due to yellowing. The color of garden cress baby leaf was changed the lowest in 1,300 cc treatment that showed the highest chlorophyll content and Hue angle value, lowest $b^*$ value, present of yellowing at end of storage date. Therefore, 1,300 cc treatment which was most effective for yellowing and odor suppression during storage is considered to be suitable for packaging of garden cress baby leaf.

• Strategy21
• /
• s.34
• /
• pp.58-92
• /
• 2014

Even after S. Korea took 5.24 Measure(24 May 2014), N. Korea has not stopped raising provocations such as the shelling of Yeonpyeong Island, electronic and cyber attacks. To make matters worse, the communist country lunched long-range missiles(twice) and conducted 3rd nuclear test, escalating tensions which could possibly lead to an all-out war. Korean Government failed to respond properly. However, escalation into an all-out war was deterred by the CFC immediately carrying out its peacetime duty(CODA). The US made a rapid dispatch of its augmentation forces(Aircraft carrier, nuclear-powered submarine, strategic bomber, F-22) to the Korean Peninsula. In recognition of the importance of the Combined Forces Command, since May 2013 the Park Geun-Hye Administration has been pushing ahead with re-postponement of Wartime Operational Control Transfer(which initially meant the disassembling of the CFC as of 1 December 2015) More recently, there has been a series of unusual indicators from the North. Judging from its inventory of 20 nuclear weapons, 1,000 ballistic missiles and biochemical weapons, it is safe to say that N. Korea has gained at least war deterrence against S. Korea. Normally a nation with nuclear weapons shrink its size of conventional forces, but the North is pursuing the opposite, rather increasing them. In addition, there was a change of war plan by N. Korea in 2010, changing 'Conquering the Korean Peninsula' to 'Negotiation after the seizure of the Greater Seoul Metropolitan Area(GSMA)' and establishing detailed plans for wartime projects. The change reflects the chain reaction in which requests from pro-north groups within the South will lead to the proclamation of war. Kim, Jeong-Un, leader of N. Korean regime, sent threatening messages using words such as 'exercising a nuclear preemptive strike right' and 'burning of Seoul'. Nam, Jae-June, Director of National Intelligence Service, stated that Kim, Jung-Un is throwing big talks, saying communization of the entire Korean Peninsula will come within the time frame of 3 years. Kim, Gwan-Jin, Defense Minister, shared an alarming message that there is a high possibility that the North will raise local provocations or a full-fledged war whenever while putting much emphasis on defense posture. As for the response concept of the Korean Government, it has been decided that 'ROK·US Combined Local Provocation Counter-Measure' will be adopted to act against local provocations from the North. Major provocation types include ▲ violation of the Northern Limit Line(NLL) with mobilization of military ships ▲ artillery provocations on Northwestern Islands ▲ low altitude airborne intrusion ▲ rear infiltration of SOF ▲ local conflicts within the Military Demarcation Line(MDL) ▲ attacking friendly ships by submarines. Counter-measures currently established by the US involves the support from USFK and USFJ. In order to keep the sworn promise, the US is reinforcing both USFK and USFJ. An all-out war situation will be met by 'CFC OPLAN5027' and 'Tailored Expansion Deterrence Forces' with the CFC playing a central role. The US augmentation forces stands at 690,000 troops, some 160 ships, 2,000 aircraft and this comprise 50% of US total forces, which is estimated to be ninefold of Korean forces. The CFC needs to be in center in handling both local provocations and an all-out war situation. However, the combat power of S. Korean conventional forces is approximately around 80% of that of N. Korea, which has been confirmed from comments made by Kim, Gwan-Jin, Defense Minister, during an interpellation session at the National Assembly. This means that S. Korean forces are not much growing. In particular, asymmetric capabilities of the North is posing a serious threat to the South including WMD, cyber warfare forces, SOF, forces targeting 5 Northwestern Islands, sub-surface and amphibious assault forces. The presence of such threats urgently requires immediate complementary efforts. For complementary efforts, the Korean Government should consider ① reinforcement of Korean forces; putting a stoppage to shrinking military, acquisition of adequate defense budget, building a missile defense and military leadership structure validity review, ② implementation of military tasks against the North; disciplinary measures on the sinking of ROKS Cheon-an/shelling of Yeonpyeong Islands, arrangement of inter-Korean military agreements, drawing lessons from studies on the correlation between aid for N. Korea, execution of inter-Korean Summit and provocations from the North, and ③ bolstering the ROK·US alliance; disregarding wartime operational control transfer plan(disassembling of CFC) and creation of a combined division.

• Journal of Bio-Environment Control
• /
• v.18 no.4
• /
• pp.454-459
• /
• 2009

The secondary growth of garlic depreciates the quality of a bulb and, in the worse cases, makes it difficult to be used as a seed bulb due to many insertions of small cloves in the seed bulb. Therefore, the effect of soil temperature, seedtime, and fertilization rate on the secondary growth of the big bulbils of Namdo garlic has been examined. When we analyzed into the growth characteristics of big bulbils of Namdo garlic under different fertilizer application levels (50% increased fertilization, experimental fertilization and 50% decreased fertilization), the plant height, numbers of leaf, sheathe diameter, leaf length, and leaf width were the best in 50% increase of the test rate of fertilizer. The occurrence rates of secondary growth were 34.2% in 50% decrease of the test rate of fertilizer, 44.3% in the test rate, and 54.1% in 50% increase of the test rate of fertilizer. In other words, the occurrence rate of secondary growth increased by increasing the fertilization rate. While the average harvested bulb weight were 34.1g in 50% decrease of the test rate of fertilizer, 35.1g in the test rate of fertilizer, and 33.9g in 50% increase of the test rate of fertilizer, there were no changes in the number of cloves under different fertilization rates. As the correlation diagram between the soil temperature and occurrence of the secondary growth showed very high relation with 0.892~0.997, the secondary growth in cultivation of Namdo garlic big bulbils had considerably close correlation with the soil temperature. As the earlier the seedtime was, the growth of the above-groundparts including the plant height, numbers of leaf, and sheath diameter were the better. The averages of bulb weight were 36g in the mid September sowed seed bulb, 29.6g in the late September sowed seed bulb, and 27.9g in the early October sowed seed bulb. Overall, our results showed that the bulb size is dependent on the seedtime and the seedtime has no particular effects on the secondary growth.

• The Korean Journal of Nuclear Medicine
• /
• v.34 no.1
• /
• pp.82-93
• /
• 2000

Purpose: We characterized the signals obtained from the components of a small gamma camera using Nal(Tl)-position sensitive photomultiplier tube (PSPMT) and optimized the parameters employed in the modules of the system. Materials and Methods: The small gamma camera system consists of a Nal(Tl) crystal ($60{\times}60{\times}6mm^3$) coupled with a Hamamatsu R3941 PSPMT, a resister chain circuit, preamplifiers, nuclear instrument modules (NIMs), an analog to digital converter and a personal computer for control and display. The PSPMT was read out using a resistive charge division circuit which multiplexes the 34 cross wire anode channels into 4 signals (X+, X-, Y+, Y -). Those signals were individually amplified by four preamplifiers and then, shaped and amplified by amplifiers. The signals were discriminated and digitized via triggering signal and used to localize the position of an event by applying the Anger logic. The gamma camera control and image display was performed by a program implemented using a graphic software. Results: The characteristics of signal and the parameters employed in each module of the system were presented. The intrinsic sensitivity of the system was approximately $8{\times}10^3$ counts/sec/${\mu}Ci$. The intrinsic energy resolution of the system was 18% FWHM at 140 keV. The spatial resolution obtained using a line-slit mask and $^{99m}Tc$ point source were, respectively, 2.2 and 2.3 mm FWHM in X and Y directions. Breast phantom containing $2{\sim}7mm$ diameter spheres was successfully imaged with a parallel hole collimator. The image displayed accurate size and activity distribution over the imaging field of view Conclusion: We proposed a simple method for development of a small gamma camera and presented the characteristics of the signals from the system and the optimized parameters used in the modules of the small gamma camera.

• Korean Journal of Food Science and Technology
• /
• v.33 no.4
• /
• pp.437-443
• /
• 2001

Gastrodia elata blume (GEB) is considered to be a useful herbal medicine in oriental countries for the treatment of headache, migraine, dizziness, childhood convulsion, epilepsy, rheumatism, hypertension, neuralgia and neurological disorders. This study was carried out to investigate the quality of bread added with the powder of GEB. The possibility of GEB wheat flour mixture as bread was studied by adding 0%, 0.5%, 1.0%, 1.5%, 2.0% of GEB powder to wheat flour. In Farinograph data, the dough stability decreased with the increase of GEB powder. Granular size of starches ranged from $36\;{\mu}m\;to\;60{\mu}m$, and the shape of them showed a long oval figure. Amylograph showed that the increase in the ratio of GEB on the doughs slightly elevated in the maximum viscosity. The loaf volume of 0.5% powder increased by 10.2% but that of 2.0% decreased by 16.8%. The moisture content was 43.57% in the control but it increased as the powder addition. The colors of crust and crumb were not significantly different among L, b and ${\Delta}E$, but 'a' value in crumb was increased as the powder addition. The addition of the powder had no significant effect on bread texture. In sensory evaluation, the moistness increased as the increase of the powder addition. The control bread was most excellent, and the bread made by mixing additives were better than just 0.5% GEB-wheat flour in terms of quality.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.40 no.10
• /
• pp.1474-1481
• /
• 2011

This study investigated the physicochemical characteristics of Korean wheat flour substituted for 0%, 15%, 30%, 45%, and 60% durum rimachinata wheat in order to develop a Korean wheat pasta suitable for consumer-preferred soft textures. The particles of Korean wheat that were less than 250 ${\mu}M$ were 87.03% of all particles, while 68.7% of durum rimachinata had particles more than 250 ${\mu}M$ in size. Durum rimachinata had more protein (13.84${\pm}$0.03) and ash (0.70${\pm}$0.02) than Korean wheat. In farinograph characteristics, water absorption, development time, stability, and weakness increased as the amounts of substituted Korean wheat flour increased. Also, the gelatinization characteristics of the amylograph exhibited an increase of gelatinization temperature and decrease in maximum viscosity. However, maximum viscosity was shown to be more than 550 B.U. until 30% of the substitution level of Korean wheat flour to durum rimachinata wheat. Also, it did not affect the texture of the noodle product. We could make pasta with softness and springiness with less than a 15% substitution level of Korean wheat flour due to similar characteristics in cooking properties such as weight, volume, water absorption, turbidity, and cooking loss when compared to the control. L and a values increased, and the b value decreased in color as substitution amounts of Korean wheat flour increased. The hardness and adhesiveness of cooking noodles was shown to be a low value at more than a 30% substitution level of Korean wheat flour, and springiness, gumminess, and chewiness all exhibited high values. In a sensory evaluation, overall acceptability was shown to have the highest score in control. More than 30% of substitution of Korean wheat flour showed high preferences. Therefore, 15% of the substitution level of Korean wheat flour could be adapted in dough and cooking properties for making pasta-substituted Korean wheat. However, a texture analyzer and sensory evaluation of cooked pasta was shown to have a good quality at more than 30% substitution level of Korean wheat flour.

• Journal of Dairy Science and Biotechnology
• /
• v.29 no.1
• /
• pp.23-31
• /
• 2011

Domestic dairy industry is now standing at the crossroad for planning next fifty years, mainly because economic and environmental situations surrounding Korean peninsula are fast changing. For the aspects of dairy consumption, fresh milk consumed less, while consumption of the other milk and dairy products is slightly increasing every year. In 2010, it is approximately estimated that 1,939,000 tons of raw milk was used and the supply would be short by about 35,000 tons, based on the amounts in the previous year. Currently, multilateral negotiations against US and EU are underway. When it will be in effect in the future, significant damage would be expected in the dairy and livestock sectors, leading to cut domestic milk supply. Quality of farm-gate milk is graded as 1A on average 90% or more, loaded with very low in microbial and somatic cell counts. Therefore, policy implications have to be placed toward switch currently the UHT processing method to Pasteurization or the LTLT technology, by which natural flavors and nutrients in milk mostly remain after heat treatment. Domestic cheese products comprise only 10% and the rest is occupied by the various kinds of imported natural products. The market size keeps increasing up to 65,423,000 tons last year. When it comes to vitalization of our natural cheese industry, cheese whey, which is a main by-product in cheese manufacture, is a critical issue to be solved and also "On-Farm Processing" would be combined with a growth of big dairy companies when few immediate issues among the relevant regulations will be eased and alleviated in the near future. Fermented milk market is recorded as a single area of gradual increase in the past 10 years, Korea. Fermented yogurts with health claims targeted stomach, liver, and intestine are popular and has grown fast in sales amounts. In this context, researches on beneficial probiotic lactic acid bacteria are one of the important projects for domestic milk and dairy industries. Labelling regulations on efficacy or health-promoting effects of functional dairy products, which is the most important issue facing domestic dairy processors, should be urgently examined toward commercial expression of the functionality by lawful means. Colostrum, a nutrition-rich yellowish fluid, is roaded with immune, growth and tissue repair factors. Bovine colostrum, a raw material for immune milk preparations and infant formula, can be used to treat or prevent infections of the gastrointestinal tract. Nanotechnology can be applied to develop new milk and dairy products such as micro-encapsulated lactase milk for consumers suffering lactose intolerance. Raw milk is suggested to be managed by its usage in the processing line because imbalance of supply and demand is structural problem in every country and thus the usage systems as in the advanced dairy countries is worth of bench-marking to stabilize milk supply and demand. Raw milk produced is desirable to divide into the three parts; domestic, import, and buffering purposes. It is strongly recommended that a domestic dairy control center as an institutional framework should be urgently established as is Dairy Board in New Zealand and Australia. Lastly, government policy should be directed to foster the highly-educated people who are majoring in Dairy Sciences or working in the dairy industry by means of financial support in studying and training abroad as well.

• Clinical and Experimental Pediatrics
• /
• v.48 no.1
• /
• pp.27-33
• /
• 2005

Purpose : To determine incidence, characteristics and risk factors associated with intrauterine intraventricular hemorrhage(IU-IVH) among premature infants. Methods : The medical records of infants with intraventricular hemorrhage(IVH) admitted to the neonatal intensive care unit of Asan Medical Center from January 1999 to June 2003 were reviewed retrospectively. Infants whose IVH with cystic change were detected within five days of life were defined as the IU-IVH group. The control group included those without any IVH. Various maternal and neonatal factors were evaluated between the IU-IVH and control groups, and risk factors for IU-IVH were identified using multiple logistic regression analysis. Results : The incidence of IU-IVH was 49/1024(15.9%). Mothers who are younger, primiparous, use less antenatal steroid, and neonates with greater incidence of neonatal respiratory distress syndrome, had higher incidences of IU-IVH compared to neonates with normal neurosonography. Risk factors associated with IU-IVH included neonatal respiratory distress syndrome and placenta infarct by placenta biopsy. Most infants with IU-IVH were ${\geq}1,501g$, ${\geq}34$ weeks gestational age and had low grade IVH. The size of the cysts associated with IU-IVH remained the same or disappeared in 96 %. IU-IVH does not seem to affect short-term neurodevelopmental outcome although a longer period of follow-up is needed. Conculusion : IU-IVH occurred mostly in ${\geq}1,501g$, ${\geq}34$ weeks infants with grade I IVH without developmental delays. However, the high incidence of total IVH merits more attention in terms of awareness of its existence as an unusual IVH among premature infants.

• Journal of Bio-Environment Control
• /
• v.22 no.3
• /
• pp.284-290
• /
• 2013

This study analyzed the geometric, compressive, cutting and friction properties of oriental melons in order to design a gripper capable of soft handling and a cutter for cutting oriental melon vine among the end effector of oriental melon as a preliminary step for developing the end effector of the robot capable of harvesting oriental melons in protected cultivation. As a result, the average length, diameter at the midpoint, weight, volume and roundness of the oriental melons were 108 mm, 70 mm, 188 g, 333 mL and 3.8 mm. Nonlinear regression analysis was performed on the equation $W=L^a{\times}D_2^b$ with variation of the length (L) and diameter (D2) of the weight (W) of the oriental melons. As a result, it was shown that there was a correlation between a of 2.0279 and b of -0.9998 as a constant value. The average diameter of the oriental melon vine was 3.8 mm, and most vines were distributed within a radius of 5 mm from the center. The average yield value, compressive strength and hardness of the oriental melons were $36.5N/cm^2$, $185.7N/cm^2$ and $636.7N/cm^2$, respectively. The average cutting force and shear strength of the oriental melon vines were $2.87{\times}10^{-2}\;N$ and $5.60N/cm^2$, respectively. The maximum friction coefficient of the oriental melons was rubber of 0.609, followed by aluminium of 0.393, stainless steel of 0.177 and teflon of 0.079. It was considered possible to apply it to the size of the gripper and cutter, turning radius, dynamics of drive motor and selection of materials and their quality in light of the position error and safety factor according to the movement when designing end effector based on the analyzed data.