• Steel and Composite Structures
• /
• 제12권6호
• /
• pp.505-522
• /
• 2012

An artificial bee colony (ABC) algorithm is developed for the optimum design of geometrically non-linear steel frames. The ABC is a new swarm intelligence method which simulates the intelligent foraging behaviour of honeybee swarm for solving the optimization problems. Minimum weight design of steel frames is aimed under the strength, displacement and size constraints. The geometric non-linearity of the frame members is taken into account in the optimum design algorithm. The performance of the ABC algorithm is tested on three steel frames taken from literature. The results obtained from the design examples demonstrate that the ABC algorithm could find better designs than other meta-heuristic optimization algorithms in shorter time.

• 소음진동
• /
• 제5권2호
• /
• pp.225-234
• /
• 1995

In this study, first, transformation process of damping ratios, whose are evaluated in active control analysis, into damping matrix resulting from installed viscous dampers is illustrated. Then, a method is followed to maximize the effect of response reduction, which leads to optimum locations and size of viscous dampers using sensitivity analysis. Highly coupled nonlinearity between damping ratios and dampers makes it hard to find the optimal size of dampers. Therefore, the nonlinearity is transformed to linear problem with small increments of damping ratios and the size of dampers can be found. However, there are many cases for the size of dampers satisfying the small increment of damping ratios, so it is necessary to select minimum size using optimization technique. To determine optimum locations of dampers, dampers are assumed to be installed between the different stories and their locations are selected corresponding corresponding to the degree of damping size. Numerical examples for the frame structure and the shear wall structure show that optimum locations and size of dampers are different form each other depending on the characteristics of modal responses of the structures. The proposed method in this study can be applied to get optimum locations of active controller in the active control.

• 대한조선학회논문집
• /
• 제40권4호
• /
• pp.53-58
• /
• 2003

Design of the corrugated watertight bulkhead for a bulk carrier is principally determined by the permissible limit of Classification requirements. As the weight of upper and lower stool has considerable portion of the total weight of the transverse bulkhead, optimum design including the stool geometry and size will play an important role on economic shipbuilding. The purpose of this study is focused on the minimization of steel weight using the design variables, which are the shape and the size of the corrugation as well as the upper and lower stools. Discrete variables are used as design variables for the practical design. In this study, the evolution strategies (ES), which can highly improve the possibility of leaching the global minimum point, are selected as an optimization method. Usefulness of this study is verified by comparison with the proven type ship design. As objective function, total weight of the transverse bulkhead including the upper and lower stools is used.

• Structural Engineering and Mechanics
• /
• 제73권2호
• /
• pp.153-165
• /
• 2020

The effect of soil foundation plays active role in optimum design of steel space frames when included. However, its influence on design can be calculated after a long iterative procedure. So it requires longer computer time and more computational effort if it is done properly. The main purpose of this study is to investigate how these effects can be calculated in more practical way in a shorter time. The effects of semi-rigid column bases are taken into account in optimum design of steel space frames. This study is carried out by using JAYA algorithm which is a novel and practical method based on a single revision equation. The displacement, stress and geometric size constraints are considered in the optimum design. A computer program is coded in MATLAB to achieve corporation with SAP2000-OAPI (Open Application Programming Interface) for optimum solutions. Four different steel space frames including soil structure interaction taken from literature are investigated according to different semi-rigidly supported models depending on different rotational stiffness values. And the results obtained from analyses are compared with the results available in reference studies. The results of the study show that semi-rigidly supported systems in the range of appropriate rotational stiffness values offer practical solutions in a very short time. And close agreement is obtained with the studies on optimum design of steel space frames including soil effect underneath.

• International Journal of Precision Engineering and Manufacturing
• /
• 제6권4호
• /
• pp.73-77
• /
• 2005

Linear motor has been considered to be the most suitable electric machine for linear control with high speed and high precision. Thrust of linear motor is one of the important factors to specify motor performance. Maximum thrust can be obtained by increasing the magnitude of current in conductor and is relative to the sizes of conductor and magnet. However, the magnitude of current and the size of conductor have an effect on temperature of linear motor. Therefore, it is practically important to find optimum design that can effectively maximize thrust of linear motor within limited range of temperature. Finite element analysis was applied to calculate thrust and numerical solutions were compared with experiments. The temperature of the conductor was calculated from the experimentally determined thermal resistance. The ADPL of ANSYS was used for the optimum design process, which is commercial finite element analysis software. Design variables and constraints were chosen based on manufacturing feasibility and existing products. As a result, it is shown that temperature of linear motor plays an important role in determining optimum design.

• 한국강구조학회 논문집
• /
• 제12권5호통권48호
• /
• pp.515-525
• /
• 2000

본 연구의 목적은 평면 트러스의 단면치수 및 형 상 최적화 알고리즘을 개발 하는 것이다. 본 연구에 적용된 최적화 기법은 무제약 축차선형화기법(SUMT)의 extended penalty method와 다변수(多變數)를 가지는 직접탐사법인 Hooke & Jeeves method이다. 상기(上記) 언급된 두 방법은 단면최적화와 형상최적화 과정의 각 단계에서 반복적 다 최적설계 과정에서 최종의 최적값이 구해질 때까지 단면최적화와 형상최적화 과정이 반복적으로 상호작용하게 된다. 트러스의 형상최적화에 관한 기존의 연구문헌에서는 최적화의 설계변수로서 부재의 단면적과 절점좌표를 사용하였다. 이렇게 할 경우, 압축재의 좌굴특성을 제대로 반영하기 어려우므로 한정된 조건으로 좌굴특성을 부여하게 되어 보다 실제적인 최적설계에 많은 제약을 가져오게 되므로 본 연구에서는 부재의 실제치수와 절점좌표를 최적화의 설계 변수로 취하게 되므로 부재치수의 변화에 따른 좌굴특성의 변화를 최대한 반영할 수 있다.

• 대한조선학회 특별논문집
• /
• 대한조선학회 2005년도 특별논문집
• /
• pp.63-68
• /
• 2005

Optimum design of the big brackets is performed through iterated 3-D FE analyses to meet the permissible limits of stress, which consumes an excessive amount of calculation time. Therefore, this study has been prepared to determine rapidly and accurately an optimum size and scantling of the big brackets at the initial design stage. The generalized slope deflection method (GSDM) based on the span point concept is applied to enhance the efficiency of iterated structural analyses. The accuracy and applicability of the present method is verified by comparing with a detail 3-D FE analysis of web frame structures. As an optimization technique, evolution strategies (ES) are applied using discrete design variables for practical design.

• 한국공간구조학회논문집
• /
• 제10권4호
• /
• pp.59-66
• /
• 2010

본 연구는 스페이스 트러스 구조물의 초기 형상을 결정하기 위해 밀도법을 이용한 위상최적화 기술을 고려하고자 한다. 대부분의 초기 형상설계는 다양한 최적화 방법을 활용하지 않고 설계자의 경험이나 시행착오적인 방법을 바탕으로 수행되고 있다. 이런 이유로 합리적이고 경제적인 최적화기술이 초기 형상설계에 도입되어야 한다. 따라서 본 연구에서는 스페이스 트러스 구조물을 대상으로 설계영역을 설정하고 위상최적화를 수행하여 최적의 재료분포를 찾은 뒤 크기최적화를 이용하여 최적부재 크기를 찾고자 한다. 이와 같이 밀도법을 이용한 위상 및 크기최적화를 병행하여 수행할 경우 합리적인 스페이스 트러스 구조물의 초기 형상을 도출할 수 있다.

• 한국해양공학회지
• /
• 제23권1호
• /
• pp.1-6
• /
• 2009

The paper describes results of a sensitivity study on an optimum mooring cost as a function of safety factor and allowable maximum offset of the offshore floating structure by finding the anchor leg component size and the declination angle. A harmony search (HS) based mooring optimization program was developed to conduct the study. This mooring optimization model was integrated with a frequency-domain global motion analysis program to assess both cost and design constraints of the mooring system. To find a trend of anchor leg system cost for the proposed sensitivity study, optimum costs after a certain number of improvisation were found and compared. For a case study a turret-moored FPSO with 3 ${\times}$ 3 anchor leg system was considered. To better guide search for the optimum cost, three different penalty functions were applied. The results show that the presented HS-based cost-optimum offshore mooring design tool can be used to find optimum mooring design values such as declination angle and horizontal end point separation as well as a cost-optimum mooring system in case either the allowable maximum offset or factor of safety varies.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2001년도 추계학술대회논문집 I
• /
• pp.419-426
• /
• 2001

Industrial products determined by fixed size posses definite limits variety by manufacture tolerance in existence. The optimum value solved by deterministic approaches do not account of tolerance bands of design variables and material properties. If we examine optimum value considering tolerance bands of design variables and material properties, it might be useless, owing to exist infeasible region. We have two ways to prevent being useless value. The one is to minimize tolerance band, the other is to consider tolerance band in optimum design. The former needed more accuracy during manufacturing process require higher production cost, the letter is more appropriate to consider tolerance band. In this research, we consider the tolerance bands of all variables, which might have the tolerance bands used in the problem, based on optimum value of deterministic approaches. Orthogonal arrays are used to minimize the number of trial. Tolerance bands are supposed discretionary according to design variable. Appropriateness suggested by this research is examined through two examples. Mathematical problem is investigated only in terms of tolerance bands of design variables, and cantilever beam problem is explained through tolerance bands of design variable, material properties and loading conditions. It is proved that values from the presented method are satisfactory for tolerance bands of variables.