• 전력전자학회:학술대회논문집
• /
• 전력전자학회 1998년도 전력전자학술대회 논문집
• /
• pp.149-153
• /
• 1998

In this paper A switched mode AC/DC three phase boost converter with high power factor and sinusoidal input current waveform is analyzed and simulated. The proposed converter retain high power factor and sinusoidal input current waveform even under electric arc welder load. It is shown that experimental result and simulation waveform yield a sinusoidal input current waveform at high power factor.

• 한국자기학회지
• /
• 제22권1호
• /
• pp.23-26
• /
• 2012

정현파 자속밀도 조건에서 연자성 재료의 교류자기손실을 측정하기 위한 새로운 방법을 제시하였다. 본 방법은 입력전압파형을 결정짓기 위해 통상 이용하는 $H_i(B_i)$곡선대신 $V_{in}$(B)곡선을 이용함으로서 자기장, 자속밀도 그리고 입력전압간의 위상차를 고려할 필요가 없이 직접 입력전압파형을 얻을 수 있어 프로그램이 간편하게 되는 장점을 가지고 있었다. 개발된 측정방법의 유효성을 1 kHz, 10 kHz 주파수에서 페라이트 코어로 확인할 수 있었다.

• 조명전기설비학회논문지
• /
• 제21권9호
• /
• pp.39-46
• /
• 2007

This paper presents a programmable single-phase ac power source that provides a sinusoidal output voltage with an adjustable output amplitude and frequency over a wide range as well as an arbitrary waveform. The ac power source under consideration have a linear power amplifier. The desired output values can be programmed with a personal computer. The power source operates at 220[V]/60[Hz] mains and the output voltage is isolated from the input circuit. The system consists mainly of a power converter to generate and amplify the waveform signal, a controller to control the desired output signal and measure the output parameters, and a control program to set the desired output and display the values. The prototype ac power source was constructed and tested with the results demonstrating a good performance.

• 대한전기학회논문지:전기기기및에너지변환시스템부문B
• /
• 제48권8호
• /
• pp.448-454
• /
• 1999

This paper describes a new dc-ac inverter system which for achieving sinusoidal ac waveform makes use of parallel loaded high frequency resonant inverter consisting of full bridge. Each one of the pair of switches in the inverter is driven to synchronous output frequency and the other is driven to PWM signal with resonant frequency proportional to magnitude of sine wave. A forced discontinuous conduction mode is used to realize the quasi-sinusoidal pulse in each switching period. Therefore the inverter generates sinusoidal modulated output voltage including carrier frequency that is resonant frequency. Carrier frequency components of modulated output voltage is filtered by low pass filter. Since current through switches is always zero at its turn-on in the proposed inverter, low stress and low switching loss is achieved. Operating characteristics of the proposed system is analyzed in per unit system using computer simulation. The output voltage of if includes low harmonics and it is almost close to sine wave. Also, the theoretical analysis is proved through the experimental test.

• 조명전기설비학회논문지
• /
• 제19권8호
• /
• pp.102-108
• /
• 2005

본 논문에서는 소프트 스위칭에 의한 새로운 고역률 승압형 AC-DC 컨버터가 제안되고 입력전류의 파형 및 고조파분석에 대해 상세히 해석된다. 시비율 일정의 전류불연속 제어에 의해 동작되는 제안된 컨버터의 입력전류는 교류 입력전압의 크기에 비례한 불연속적인 펄스열의 정현파 형태로 되어 입력역률을 개선시킨다. 또한 제안된 컨버터는 소프트 스위칭을 위한 공진동작에 의해 무손실 스너버 커패시터의 입력측 에너지 유입에 따른 역률증대의 효과를 가지며, 기존의 고역률 승압형 AC-DC 컨버터와 비교되어 입력전류의 수학적 분석과 컴퓨터 시뮬레이션, 실험결과 등에 의해 그 우수성이 입증된다.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2001년도 합동 추계학술대회 논문집 정보 및 제어부문
• /
• pp.338-340
• /
• 2001

Power factor improved for single-phase buck-converter is studied in the paper. To sinusoidal waveform the input current with a near-unity power factor over a wide variety of operating conditions, the output capacitor is operated with voltage reversibility for the supply by arranging the auxiliary diode and power switching device. Then the output voltage is superposed on the input voltage during on time duration of power switching devices in order to minimize the input current distortion caused by the small input voltage when changing the polarity. The tested setup, using two insulated gate bipolar transistors(IGBT) and a microcomputer, is implemented and IGBT are switched with 20[kHz], which is out of the audible band. Moreover, a rigorous state-space analysis is introduced to predict the operation of the rectifier. The simulated results confirm that the input current can be sinusoidal waveform with a near-unity power factor and a satisfactory output voltage regulation can be achieved.

• 대한전자공학회논문지
• /
• 제12권2호
• /
• pp.43-46
• /
• 1975

쵸퍼형DC증폭기의 AC증폭기의 인력신호는 일련의 단형연이다. 따라서 이 때의 AC증폭기의 동작은 정장파신호에 대한 그것과 큰 차이가 있다. 본 논문은 단형파에 대한 AC증폭기의 각단에서의 파형의 찌그러짐에 대한 해석을 하여 쵸퍼용AC증폭기의 설계상의 문제점을 고찰한 것이다. 각증폭단의 시정수가 동일한 경우에는 각단의 신호파형은 모두 지수감쇠속형파로 되며, 시정수가 다를 경우에는 여러개의 지수감쇠구형파의 합성파로 된다. In a chopper amplifier the input signal of the AC amplifier is a train of square-waves. In the rase of square-wave the operatiom of AC amplifier is much different from that of ordinary sinusoidal wave. In this paper for the purpose of contributing to the design of chopper amplifier destortions of waveforms in the amplifier were investigated. When the time constant of each stage is equal the waveform in each stave apppears as square wave whose top is exponentially decaying. And when each stave has different time constant the waveform in n-th stage is composed of n-square waves whose tops are exponentially decaying.

• 대한전기학회논문지
• /
• 제36권4호
• /
• pp.259-266
• /
• 1987

In order to drive motor control system precisely, the motor is to be controlled by mmfs and current with sinusoidal waveforms. In this paper the Delta Modulation (DM) Technique is used for generating PWM pulse with sinusoidal waveform. However the motor currents yet contain odd harmonics due to leakage inductances, speed and exitation. To reduce harmonics, the parameter adaptive control method is introduced. That is, Req.C parameter of Delta Modulator is controlled adaptively by parameter adaptor. The adaptive signal is achieved by the difference between motor current and reference waveform, and this signal is converted to the voltage commend signal by adaptive mechanism. The test reslts show that this system is operated smoothly over a wide range of motor speed and motor current is controlled to be sinusoidal waveform adaptively.

• 한국정밀공학회지
• /
• 제19권12호
• /
• pp.127-133
• /
• 2002

The objective of this study is to investigate fatigue life and fatigue crack propagation behavior The experiment of fatigue life for MMC have been carried out for the stress ratio R＝0.1 at 20Hz. Fatigue lift limit of AC4CH alloy is about 70 ㎫ and Fatigue limit of MMC has been increment to 120 ㎫, therefore, fatigue limits of MMC is about 71 % higher than that of AC4CH alloy Crack propagation tests on half-size CT specimen of thickness 12.5mm were conducted by using sinusoidal waveform. The crack length was monitored by compliance method. Test conditions were at 0.1 and 0.05 of load ratio at 10Hz of loading frequency and test load was 2.3kN. The effects of stress ratio on the fatigue crack propagation behavior for MMC was discussed within the Paris law. As the results of this study, Fatigue crack propagation increased with increasing the load ratio.

• 한국조명전기설비학회지:조명전기설비
• /
• 제2권2호
• /
• pp.59-63
• /
• 1988

고정 AC 전력전원에서 PWN(Pulse Width Modulation) 기법은 전압과 기본파 주파수를 가변 시키는 데 이용되어 왔다. 종래의 PWN 기법은 전류수, 필터크기 등의 문제점 때문에 PWN 출력 전압파형을 모터 구동 등의 제어 대상에 응용하는 연구가 진행되었다. 그러나 본 논문에서는 출력단 고속 스윗칭 소자를 사용하여 캐리어 주파수를 10(KHz)-45(KHz)까지 정현 PWN 시키고, 인버터의 출력단 파형은 소용량LPF(Low Pass Filter)를 사용하여 PAM(Pulse Amplitude Modulation)을 얻어냈다. 정현 PWN 제어 회로는 속응성과 제어성을 고려하여 마이크로 프로세서와 아날로그 회로로 혼합구성 하였다. 그리고 실험 결과는 변조도 0.6-1.0까지 변할 때 전압 파형을 관찰했다.