• Journal of the Microelectronics and Packaging Society
• /
• v.26 no.4
• /
• pp.7-13
• /
• 2019

Power module is getting attention from electronic industries such as solar cell, battery and electric vehicles. Transient liquid phase (TLP) boding, sintering with Ag and Cu powders and wire bonding are applied to power module packaging. Sintering is a popular process but it has some disadvantages such as high cost, complex procedures and long bonding time. Meanwhile, TLP bonding has lower bonding temperature, cost effectiveness and less porosity. However, it also needs to improve ductility of the intermetallic compounds (IMCs) at the joint. Wire boding is also an important interconnection process between semiconductor chip and metal lead for direct bonded copper (DBC). In this study, TLP bonding using Sn-based solders and wire bonding process for power electronics packaging are described.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11a
• /
• pp.34-37
• /
• 2001

In this study, the capacitance-voltage properties of (Sr$_{1-x}$ .Ca$_{x}$)TiO$_3$(0.05$\leq$x$\leq$0.20)-based grain boundary layer ceramics were investigated. The ceramics were fabricated by the conventional mixed oxide method. The sintering temperature and time were 1480~150$0^{\circ}C$ and 4 hours, respectively. The 2nd phase formed by the thermal diffusion of CuO from the surface leads to very excellent dielectric properties, that is, $\varepsilon$$_{r}$>50000, tan$\delta$<0.05, $\Delta$C<$\pm$10%. The capacitance is almost unchanged below about 20[V] but it decreases slowly about 20[V]. The results of the capacitance-voltage properties indicated that the grain boundary was composed of the continuous insulating layers.ulating layers.s.

• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.312-313
• /
• 2006

The primary aim pursued by the preparation of separation membrane is the preparation of the membrane thin as well as with no defect. The field-flow fractionation deposition is a new molding technology which can overcome the traditional disadvantages such as multi-preparation to the preparation of great area of separation membrane with no defect. Therefor the mainly ingredients which influence the appearance and performance of titanium membrane layer are investigated by scanning electricity mirror (SEM) as well as porous material testing instrument: powder performance prepared and confected; selection of supporting body; sintering system such as temperature and time. It is shown that the membrane thickness can be controlled at $50{\mu}m$ or so; the filtration precision mainly rests with powder performance and selection of supporting body and little sintering system

• Journal of the Korean Society of Safety
• /
• v.24 no.4
• /
• pp.22-27
• /
• 2009

In this paper, the minuteness structure, piezoelectric, and dielectric characteristics of $0.95{Pb(Sb_{1/2}Nb_{1/2})_{0.02})_{0.02}(Ni_{1/3}Nb_{2/3})_{0.13}(Zr_{0.48}Ti_{0.52})_{0.85}}O_3+0.05Pb(CO_{1/2}W_{1/2})O_3+0.3%$ $MnO_2+0.3wt%$ CuO ceramics has been systematically investigated as a function of the sintering temperature after manufacturing the specimens with a general method. This study will be very helpful as basic data for developing ceramic materials, More study in a soon time for improving stability of temperature, effect of adds and stability and reality of frequency with improved production condition for specimens will give a powerful potentiality as a applied material of dielectric ceramics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.18 no.1
• /
• pp.101-108
• /
• 2019

In this study, the hole-cavity resonance technology and the micro pore stainless chip sintering technology were fused to develop silencers with excellent noise attenuation performance even at fluid pressures exceeding 30 bar for the first time at home and abroad. As a result of this study, the noise attenuation performance was greatly improved as reflection, loss, and resonance were made to occur thousands of times simultaneously when fluids pass through the sintered micro pore stainless steel chip sound absorber. The noise of the gas emitted from the bomb without the silencer was shown to be 125dB. And noise test conducted after installation of the silencer showed the noise of 67dB. Given the study results, the amount of noise was greatly reduced in the sintered silencer.

• Journal of the Korean Ceramic Society
• /
• v.29 no.7
• /
• pp.558-564
• /
• 1992

The effect of composed phase in the hot pressed CaO-MgO-Al2O3-SiO2 glass-ceramic has been investigated through microstructure studies, thermal, physical and mechanical properties. Sintering was done in the condition at the temperature range 900~95$0^{\circ}C$ for 20~120 mins under 7.5 MPa unilateral pressure. Sintered ceramics were composed of diopside, anorthite, residual glass and the portion of each phase was dependent on the sintering temperature and the holding time: as the temperature increases, the amount of diopside increased and then the rate of increase of diopside reduced with increasing anorthite. The thermal expansion coefficient of hot pressed was reduced with increasing crystallinity of hot pressed and was in the range of 6.69~7.46$\times$10-6 K-1 below $600^{\circ}C$. The elastic constant of hot pressed increased with increasing crystallinity up to about 80%, but after that was reduced due to the change of microstructure. The flexural strength of sintered ceramics was decreased with higher temperature and holding time, while the fracture toughness of those increased. It was shown that the physical and mechanical properties of hot pressed ceramic were related to the fraction of composed sintered ceramics, similar to a particulate composite, to the crystallinity of 80% of the glass-ceramic.

• Computers and Concrete
• /
• v.13 no.3
• /
• pp.325-342
• /
• 2014

The use of lightweight aggregate (LWA) instead of ordinary aggregate may make lightweight aggregate concrete, which possesses many advantages such as lightweight, lower thermal conductivity, and better fire and seismic resistance. Recently the developments of LWA have been focused on using industrial wastes as raw materials to reduce the use of limited natural resources. In view of this, the intent of this study was to apply Taguchi optimization technique in determining process condition for producing synthetic LWA by incorporating waste thin film transition liquid crystal displays (TFT-LCD) glass powder with reservoir sediments. In the study the waste TFT-LCD glass cullet was used as an additive. It was incorporated with reservoir sediments to produce LWA. Taguchi method with an orthogonal array L16(45) and five controllable 4-level factors (i.e., cullet content, preheat temperature, preheat time, sintering temperature, and sintering time) was adopted. Then, in order to optimize the selected parameters, the analysis of variance method was used to explore the effects of the experimental factors on the performances (particle density, water absorption, bloating ratio, and loss of ignition) of the produced LWA. The results showed that it is possible to produce high performance LWA by incorporating waste TFT-LCD glass cullet with reservoir sediments. Moreover, Taguchi method is a promising approach for optimizing process condition of synthetic LWA using recycled glass cullet and reservoir sediments and it significantly reduces the number of tests.

• Journal of the Korean Magnetics Society
• /
• v.7 no.6
• /
• pp.285-292
• /
• 1997

We have studied magnetoelectric effect with cobalt ferrite-Pb(Zr, Ti) $O_3$ composites made by solid state reaction. The maximum magnetoelectric voltage coefficient, $(dE/ dH)_{max}$, increased with longer sintering time and higher volume fraction of the cobalt ferrite. The magnetic field for $(dE/ dH)_{max}$ became lower with increasing the sintering time and decreasing the volume fraction of the cobalt ferrite. The phenomena were explained in terms of grain size change, mechanical coupling efficiency, easiness of magnetization and polarization. We obtained the highest magnetoelectric voltage coefficient of 0.174V/cm-Oe, which is about 30% higher than the best value reported.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.310-313
• /
• 1989

The semiconducting bodies were prepared by doping the bariume titanate with $Sb_2O_3,Nb_2O_5$and by subsequent sintering in air. The sintered bodies were annealed between $1100^{\circ}C$ and $1250^{\circ}C$ for 30 minutes to 2 hours in air. The resistivity was measured as a function of temperature from $20^{\circ}C$ to $240^{\circ}C$. The anomalous effect in resistivity occurred all of the $Nb_2O_5$ and $Sb_2O_3$doped barium titanate specimens, which were sintered in air atmosphere, and the most effective PTC effect occurred through 1 hour of sintering time at $1350^{\circ}C$ and 30 minute of annealing time at $1200^{\circ}C$. The resistivity - temperature characteristics seem to be intimately related to oxygen adsorption at grain boundaries and also to the thickness of insulating layers formed at grain boundaries during heat treatment.

• Proceedings of the Korean Society of Machine Tool Engineers Conference
• /
• 2003.10a
• /
• pp.59-65
• /
• 2003

Four kinds of $Si_3N_4$-based ceramic cutting tools with different sintering time were fabricated to investigante the effect of sintering time on the microstructure, mechanical properties, grain sizes and the cutting performance. An endeavor was also made to determine the relation among mechanical property, Brain size and tool life. $Si_3N_4$ home made cutting tool sintered for 1 hour under $1760^{\circ}$ temperature and 25MPa pressure showed the best cutting performance among selected ceramic tools during machining both Bray cast iron and heat treated SCM440. Multiple linear regression model was used to estimate the tool lift from mechanical property, grain size and showed good result. It was also shown that hardness imposed the biggest offect on tool life.