• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.769-774
• /
• 2002

금속 산화물 상태으 혼합분말을 수소 환원하여 $Al_2O_3$ 분말 표면에 20 nm 크기의 Fe-Ni 합금이 균일하게 분산된 복합분말을 합성하였다. 상압소결을 이용하여 제조한 $Al_2O_3$/Fe-Ni 나노복합재료는 전 소결 온도 범위에서 단지 $Al_2O_3$와 ${gamma}$-Fe-Ni 상만으로 구성되어 있었고, $1350^{\circ}C$ 이상의 소결 온도에서 98% 이상의 치밀화를 이루었다. 최대 파괴강도와 파괴인성은 각각 574 MPa과 3.9 MP$a{\cdot}m1/2$로서 동일한 소결 조건의 순수 $Al_2O_3$ 보다 약 20% 증가하였다. 나노복합재료는 강자성 거동을 보였으며 분산상의 평균 입자 크기가 감소함에 따라 증가된 보자력 값을 나타내었다.

• 한국진공학회:학술대회논문집
• /
• 한국진공학회 2011년도 제40회 동계학술대회 초록집
• /
• pp.207-207
• /
• 2011

Amorphous transparent oxide semiconductors (a-TOS) have been widely studied for many optoelectronic devices such as AM-OLED (active-matrix organic light emitting diodes). Recently, Nomura et al. demonstrated high performance amorphous IGZO (In-Ga-Zn-O) TFTs.1 Despite the amorphous structure, due to the conduction band minimum (CBM) that made of spherically extended s-orbitals of the constituent metals, an a-IGZO TFT shows high mobility.2,3 But IGZO films contain high cost rare metals. Therefore, we need to investigate the alternatives. Because Aluminum has a high bond enthalpy with oxygen atom and Alumina has a high lattice energy, we try to replace Gallium with Aluminum that is high reserve low cost material. In this study, we focused on the electrical properties of IZO:Al thin films as a channel layer of TFTs. IZO:Al were deposited on unheated non-alkali glass substrates (5 cm ${\times}$ 5 cm) by magnetron co-sputtering system with two cathodes equipped with IZO target and Al target, respectively. The sintered ceramic IZO disc (3 inch ${\phi}$, 5 mm t) and metal Al target (3 inch ${\phi}$, 5 mm t) are used for deposition. The O2 gas was used as the reactive gas to control carrier concentration and mobility. Deposition was carried out under various sputtering conditions to investigate the effect of sputtering process on the characteristics of IZO:Al thin films. Correlation between sputtering factors and electronic properties of the film will be discussed in detail.

• 한국분말재료학회지
• /
• 제25권2호
• /
• pp.158-164
• /
• 2018

Multi-walled carbon nanotube (MWCNT)-copper (Cu) composites are successfully fabricated by a combination of a binder-free wet mixing and spark plasma sintering (SPS) process. The SPS is performed under various conditions to investigate optimized processing conditions for minimizing the structural defects of CNTs and densifying the MWCNT-Cu composites. The electrical conductivities of MWCNT-Cu composites are slightly increased for compositions containing up to 1 vol.% CNT and remain above the value for sintered Cu up to 2 vol.% CNT. Uniformly dispersed CNTs in the Cu matrix with clean interfaces between the treated MWCNT and Cu leading to effective electrical transfer from the treated MWCNT to the Cu is believed to be the origin of the improved electrical conductivity of the treated MWCNT-Cu composites. The results indicate the possibility of exploiting CNTs as a contributing reinforcement phase for improving the electrical conductivity and mechanical properties in the Cu matrix composites.

• 대한전기학회논문지:전기물성ㆍ응용부문C
• /
• 제51권4호
• /
• pp.141-146
• /
• 2002

The mechanical and electrical properties of the pressureless sintered SiC-TiB$_2$electroconductive ceramic composites were investigated as functions of the transition metal of TiB$_2$. The result of phase analysis for the SiC-TiB$_2$ composites by XRD revealed $\alpha$-SiC(6H), TiB$_2$, and YAG(Al$_{5}$Y$_3$O$_{12}$) crystal phases. The relative density showed the lowest 84.8% for the SiC-TiB$_2$composites added with 39vol.%TiB$_2$. Owing to crack deflection, crack bridging and YAG of fracture toughness mechanism, the fracture toughness showed the highest value of 7.8 MPa.m$^{1}$2/ for composites added with 39vol.%TiB$_2$under a pressureless annealing at room temperature. The electrical resistivity of the SiC-27vol.%TiB$_2$ composites was negative temperature coefficient resistance(NTCR), and the electrical resistivity of the besides SiC-27vol.%TiB$_2$composites was all positive temperature coefficient resistance(PCTR) in the temperature range of $25^{\circ}C$ to $700^{\circ}C$.EX>.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권10호
• /
• pp.991-1000
• /
• 1996

PbTiO$_{3}$-PbZrO$_{3}$-Pb(Ni$_{1}$3/Nb$_{2}$3/O$_{3}$) (PZT-PNN) thin films were prepared from corresponding metal organics partially stabilized with diethanolamine by the sol-gel spin coating method. Each mol ratio of PT:PZ:PNN solutions were #1(50:40:10), #2(50:30:20), #3(45:35:20), #4(40:40:20), #5(40:50:10), #6(35:45:20) and #7(30:50:20) respectively. The spin-coated PZT-PNN films were heat-treated at 350.deg. C for decomposition of residual organics, and were sintered from 450.deg. C to 750.deg. C for crystallization. The substrates, such as Pt and Pt/TiN/Ti/TiN/Si were used for the spin coating of PZT PNN films. The perovskite phase was observed in the PZT-PNN films heat-treated at 500.deg. C. The crystalline of the PZT-PNN films was optimized at the sintering of 700.deg. C. By the result of AES analysis, It is confirmed that the films of TiN/Ti/TiN was a good diffusion barrier and that co-diffusion into the each films was not observed.

• 한국환경과학회지
• /
• 제1권1호
• /
• pp.41-46
• /
• 1992

주거지역에서 대기오염물 시료채취에 대한 장기간 연구를 수행하기 위해서 휘발성 유기 화합물 분석에 적합한 24시간동안의 종합적인 공기시료를 채취하기 위해 공기시료 채취기가 제작되었다. 이 시료 채취기는 시료채취시 요구되는 모든 특성을 포함할 뿐만 아니라, 일반가정에 근접해서 설치되어야하므로 심미적 특성도 포함한다. 이 공기시료 채취기는 흡착제(티넥스)로 채워진 5/8인치 외경의 스테인레스 스틸 트랩 네개를 수용할수 있고, 분당 5-50 밀리리터의 범위에서 네 종류의 공기유속을 이용할수 있게 고안 되었다. 금속필도(10마이크로미터)가 트랩 어댑터의 입구에 직접 부착되었다. 부가적인 특성은 다음과 같다. : 1) 유기물질에 불활성인 재료로 제작 되었고, 2) 날씨에 영향을 받지 않고, 3) 전지를 이용하고, 4) 사람의 호흡영역에서 공기 시료를 채취하고, 그리고 5) 방음제로 싸여진 작은 펌프를 이용하여 조용하게 작동된다. 펌프/전지 장치는 시료채취기의 본체로부터 분리 되었다. 이 장치로 부터 야기되는 소음수준은 주거지역의 허용기준치(뉴저지주 환경보호국 기준)보다 낮았다. 이 공기시료 채취기는 일상 주거지역과 단층의 한 국민학교 옥상에서 성공적으로 작동되었다.

• 자원리싸이클링
• /
• 제4권4호
• /
• pp.59-69
• /
• 1995

분진 중에 함유된 Zn, Pb, Fe 등의 유가 금속을 회수하기 위해 폐타이어를 건류하여 만든 건류탄소를 환원제로 이용하여 재활용하고자 하였으며 또한 분진을 Pelletizing 하거나 Briquetting해서 환원 처리할 때, 공해 발생과 작업상의 단점을 보완하기 위하여 제지공장에서 발생하는 폐펄프와 분진 및 건류탄소를 소정의 비율로 혼합한 후 성형한 다음 통기도 및 압축강도실험 등을 한 결과 다음과 같은 결론을 얻었다. 동일한 건류탄소 첨가량에서 결합제로 사용한 폐펄프의 첨가량이 증가할수록 통기도는 증가하며 이는 시편내 Porosiaty에 기인한 영향이라 생각되며, 동일 첨가량의 폐펄프에서 건류탄소의 첨가량이 증가할수록 통기도는 증가하는 경향을 보이며 압축강도는 건류탄소의 비율과 소결온도에 따라 증가 감소의 현상이 다소 상반되는 결과가 나타났다. 건류탄소 20%, 폐펄프 10%를 첨가하여 만든 Briguetting 시료를 X-선 회절분석 결과 $800^{\circ}C$에서는 ZnO와 $Fe_3$$O_4$가 조사되었으나 $1000^{\circ}C$ 이상에서는 ZnO와 $Fe_3$$O_4$를 확인할 수 없었다. $1000^{\circ}C$에서 소결실험을 한 결과 아연, 철산화물이 분해 증발하여 아연품위가 62%인 조산화아연물을 얻을 수 있었다.

• The Journal of Advanced Prosthodontics
• /
• 제11권5호
• /
• pp.262-270
• /
• 2019

PURPOSE. The purpose of this in vitro study was to evaluate the marginal misfits of three-unit frameworks fabricated with conventional and digital impressions techniques. MATERIALS AND METHODS. Thirty brass canine and second premolar abutment preparations were fabricated by using a computer numerical control machine and were randomly divided into 3 groups (n=10) as follows: conventional impression group (Group Ci), Cerec Omnicam (Group Cdi), and 3shape TRIOS-3 (Group Tdi) digital impression groups. The laser-sintered metal frameworks were designed and fabricated with conventional and digital impressions. The marginal adaptation was assessed with a stereomicroscope at ${\times}30$ magnification. The data were analyzed with 1-way analysis of variances (ANOVAs) and the independent simple t tests. RESULTS. A statistically significant difference was found between the frameworks fabricated by conventional methods and those fabricated by digital impression methods. Multiple comparison results revealed that the frameworks in Group Ci (average, $98.8{\pm}16.43{\mu}m$; canine, $93.59{\pm}16.82{\mu}m$; premolar, $104.10{\pm}15.02{\mu}m$) had larger marginal misfit values than those in Group Cdi (average, $63.78{\pm}14.05{\mu}m$; canine, $62.73{\pm}13.71{\mu}m$; premolar, $64.84{\pm}15.06{\mu}m$) and Group Tdi (average, $65.14{\pm}18.05{\mu}m$; canine, $70.64{\pm}19.02{\mu}m$; premolar, $59.64{\pm}16.10{\mu}m$) (P=.000 for average; P=.001 for canine; P<.001 for premolar). No statistical difference was found between the marginal misfits of canine and premolar abutment teeth within the same groups (P>.05). CONCLUSION. The three-unit frameworks fabricated with digital impression techniques showed better marginal fit compared to conventional impression techniques. All marginal misfit values were clinically acceptable.

• 한국초전도ㆍ저온공학회논문지
• /
• 제24권3호
• /
• pp.47-51
• /
• 2022

With the innovative development of bio, pharmaceutical, and semiconductor technologies, it is essential to demand a next-generation transfer system that minimizes dust and vibrations generated during the manufacturing process. In order to develop dust-free and non-contact transfer systems, the high temperature superconductor (HTS) bulks have been applied as a magnet for levitation. However, sintered HTS bulk magnets are limited in their applications due to their relatively low critical current density (J_c) of several kA/cm² and low mechanical properties as a ceramic material. In addition, during cooling to cryogenic temperatures repeatedly, cracks and damage may occur by thermal shock. On the other hand, the bulk magnets made by stacked HTS tapes have various advantages, such as relatively high mechanical properties by alternate stacking of the metal and ceramic layer, high magnetic levitation performance by using coated conductors with high J_c of several MA/cm², consistent superconducting properties, miniaturization, light-weight, etc. In this study, we tried to fabricate HTS tapes stacked bulk magnets with 60 mm × 60 mm area and various numbers of HTS tape stacked layers for magnetic levitation. In order to examine the levitation forces of bulk magnets stacked with HTS tapes from 1 to 16 layers, specialized force measurement apparatus was made and adapted to measure the levitation force. By increasing the number of HTS tapes stacked layers, the levitation force of bulk magnet become larger. 16 HTS tapes stacked bulk magnets show promising levitation force of about 23.5 N, 6.538 kPa at 10 mm of levitated distance from NdFeB permanent magnet.

• 한국세라믹학회지
• /
• 제39권8호
• /
• pp.728-734
• /
• 2002

전기로 더스트를 점토 또는 백토와 혼합하여 소성온도에 따른 전기로 더스트 내에 존재하는 Cr, Cd, Cu, Pb, Fe, Zn 중금속들의 거동을 조사하였다. 전기로 더스트를 점토와 백토에 각각 0∼50 wt%씩 첨가하였고, 소성은 $200^{\circ}C$ 간격으로 $200∼1200^{\circ}C$ 범위 내에서 수행하였다. 소성된 시편은 TCLP법에 의한 용출실험을 거친 후 ICP-AES로 분석하였다. 중금속표준용액을 이용한 양이온 교환능 실험결과 점토와 백토가 기존의 중금속 흡착제인 제올라이트와 비슷한 중금속 양이온 교환능을 보였으며, Cr에 대해서는 더 우수한 교환능이 관찰되었다. TCLP법에 의한 용출실험 결과 Cr과 Fe는 모든 시편에서 거의 용출되지 않았으며, Cd과 Zn은 소성온도가 증가하고 전기로 더스트의 함량이 적을수록 용출량이 감소하였다. 점토 또는 백토와 전기로 더스트를 혼합 소성 시 일차적으로 양이온 교환능에 의해 중금속이 준안정화되고 이차적으로 공융반응에 의하여 중금속들이 완전하게 고정화되어 중금속 용출을 억제하는 것으로 추정된다. 본 연구에서 백토가 점토 보다는 전기로 더스트 중금속의 안정화에 더 효과적이었다.