• The Journal of Advanced Prosthodontics
• /
• 제9권4호
• /
• pp.308-314
• /
• 2017

PURPOSE. The purpose of this study was to analyze the retention force changes and wear behaviours of double-crown systems over long-term use. MATERIALS AND METHODS. Ten groups, each consisting of six samples, were evaluated. Specifically, casting gold alloy primary crown - casting gold alloy secondary crown (AA), laser sintering primary crown - laser sintering secondary crown (LL), casting Cr alloy primary crown - casting Cr alloy secondary crown, (CC) zirconia primary crown - electroformed secondary crown (ZA), and CAD/CAM titanium alloy primary crown - CAD/CAM titanium alloy secondary crown (TT) groups were evaluated at cone angles of $4^{\circ}$ and $6^{\circ}$. The samples were subjected to 5,000 insertion-separation cycles in artificial saliva, and the retention forces were measured every 500 cycles. The wear levels were analyzed via SEM at the beginning and end of the 5,000 cycles. RESULTS. In all samples, the retention forces increased when the conus angle decreased. The highest initial and final retention force values were found in the $LL-4^{\circ}$ group (32.89 N-32.65 N), and the lowest retention force values were found in the $ZA6^{\circ}$ group (5.41 N-6.27 N). The ZA groups' samples showed the least change in the retention force, and no wear was observed. In the other groups, wear was observed mostly in the primary crowns. CONCLUSION. More predictable, clinically relevant, and less excursive retention forces can be observed in the ZA groups. The retention force values of the LL groups were statically similar to those of the other groups, except the ZA groups.

• 한국재료학회지
• /
• 제9권5호
• /
• pp.520-527
• /
• 1999

열전 소결재 제조의 새로운 시도로, 분말의 압출과 소결을 동시에 할 수 있는 공정에 대하여 연구하였다. $(Bi,Sb)_2(Te,Se)_3$계 압출-소결재를 제조함에 있어 제조 변수를 적절히 조절하여 건전한 표면과 미세조직을 갖는 고밀도의 소결재를 얻을 수 있었다. p형 재료의 경우 Te 도핑량이 증가함에 따라 Seebeck 계수가 증가하였으며 3 at% Te을 첨가한 경우 상온에서의 열전 성능 지수가 $2.5\times10^{-3}/K$를 나타내었다. 한편 n형 재료의 경우 0.16 mol% $SbI_3$를 도핑한 시편에서 $1.8\times10^{-3}/K$의 열전 성능지수를 보였다. p형 및 n형 재료 모두 압출 방향에 수직한 방향보다 평행한 방향으로의 운반자 이동도와 열전 성능지수가 높게 나타났다.

• 센서학회지
• /
• 제6권6호
• /
• pp.491-499
• /
• 1997

초전재료의 개발 및 박막화를 위하여 5, 10 및 15 mol%의 La 조성을 가지는 세라믹 PLT 시편 및 박막 PLT를 제조하여 그 특성을 분석하였다. PLT의 완전 소결과 Pb 성분의 휘발을 막기 위하여 TG/DTA를 사용하여 하소 및 소결온도를 결정하였다. PLT 세라믹 시편을 제조하기 위한 하소 및 소결온도는 각각 $850^{\circ}C$, $1150^{\circ}C$ 이고 더 높은 소결온도에서는 많은 질량 손실이 발생하였다. 세라믹 시편을 사용한 온도-유전율 특성의 측정으로 La 조성에 따른 PLT의 온도에 대한 유전특성을 조사하였다. 5, 10 및 15 mol%의 La 농도에 따라 PLT의 상전이점은 각각 $330^{\circ}C$, $269^{\circ}C$ 및 $210^{\circ}C$를 나타내었다. 제조된 PLT 시편을 사용하여 적외선 감지 특성을 확인하였고, 고주파 마그네트론 스퍼터링을 이용하여 PLT 박막을 증착하였다. 다음으로 격자상수 및 광투과 특성을 통하여 완전 소결된 PLT 타겟으로 제작한 PLT 박막은 타겟과 동일한 구조를 가지고 있음을 확인하였다.

• 한국세라믹학회지
• /
• 제42권12호
• /
• pp.808-815
• /
• 2005

[ $Bi_xCe_{l-x}O_{2-x/2}$ ](BD C : Bismuth Doped Ceria) powders with x = 0.1, 0.2, and 0.3 were synthesized using the Glycine Nitrate Process (GNP). They were then calcined at $500^{\circ}C$ for 2 hand sintered in a pellet or rod form at 900, 1000 or $1100^{\circ}C$ for 4 h for characterization as the alternative electrolyte material for intermediate temperature solid oxide fuel cells. The BDC powder consisted of a single phase of $CeO_2-Bi_2O_3$ solid solution in the as-synthesized state as well as in the as-calcined state with a mean powder size of 4.5nm in the former state and 6.5 - 10.1nm in the latter. On the contrary, the second phase of $\alpha-Bi_2O_3$ was observed to have been formed in the sinter with its amount increasing roughly with increasing temperature or $Bi_2O_3$ content. The BOC powder was superior in sinterability to other alternative electrolyte materials such as GDC, ScSZ, and LSGM with the minimum sintering temperature for a relative density of $95\%$ or larger as low as $1100^{\circ}C$. The ionic conductivity of BOC increased with $Bi_2O_3$ content and the maximum value of 0.119 S/cm was obtained at $800^{\circ}C$ for $Bi_{0.3}Ce_{0.7}O_{1.85}$.

• 대한기계학회논문집A
• /
• 제35권9호
• /
• pp.1035-1040
• /
• 2011

본 논문은 세라믹과 금속파우더를 이용한 복합소재를 플라즈마 용사 방식으로 개발한 결과를 수록하였다. 사용된 세라믹 파우더는 $Al_2O_3+40TiO_2$ 이고 입자 크기는 $20{\mu}m$, $Al_2O_398+$파우더의 입자 크기는 $45{\mu}m$를 사용하였다. $20{\mu}m$, $30{\mu}m$ 및 $50{\mu}m$ 금속필터 입자는 SIKA-R 20IS, 30IS 및 50IS(소결금속필터)을 사용 했으며, $75{\mu}m$ 금속필터 입자는 5 겹 소결메쉬 필터를 사용��다. 용사 공정으로 가공된 복합 필터는 세라믹 파우더의 종류, 크기 및 코팅 두께에 따라 성능의 차이를 보였으나, 전반적으로 필터링 가능 능력은 향상되었다.

• 한국세라믹학회지
• /
• 제37권4호
• /
• pp.395-401
• /
• 2000

In this study, we chose the basic composition which indicated the best electrical properties by change of x content(0, 0.05, 0.1, 0.15, 0.2, 0.25 mol respectively) in xPb(Mn1/3Sb2/3)O3-(1-x)Pb(Zr0.52Ti0.48)O3 ceramics. And we substituted Cd2+ for Pb2+ site, then observed the sintering behavior, microstructure and electrical propertties according to the various sintering temperature. The basic composition was the 0.05PMS-0.95PZt, and it showed single perovskite phase and excellent properties. In case of Cd2+ substitution, we were able to sinter at 90$0^{\circ}C$ which was lower than conventional sintering temperature(1200~130$0^{\circ}C$). Especially, when the 2mol% substituted PMS-PZT specimens were sintered at 90$0^{\circ}C$ for 2h, we obtained the p=7.6g/㎤, kp=56%, Qm=520 and made sure of a position of Cd2+ substitution by observing lattice parameter, phase transition temperature. From this results, we could infer that because Cd2+ substituted fro A-site, low temperature sintering of Cd2+ substituted PMS-PZT without any loss of electrical properties shows its applicability for the piezoelectric ceramic transformer.

• 한국세라믹학회지
• /
• 제44권7호
• /
• pp.343-348
• /
• 2007

Alumina/silver nanocomposites were fabricated using a soaking method through a sol-gel route to construct an intra-type nanostructure. The pulse electric-current sintering (PECS) technique was used to sinter the nanocomposites. Several specimens were annealed after sintering. The microstructure, mechanical properties, critical frontal process zone (FPZ) size, and thermo-mechanical properties of the nanocomposites were estimated. The relative densities of the specimens sintered at 1350 and $1450^{\circ}C$ were 95% and 99%, respectively. The maximum value of the three-point bending strength was found to be 780 MPa for the $2{\times}2{\times}10 mm$ specimen sintered at $1350^{\circ}C$. The fracture toughness of the specimen sintered at $1350^{\circ}C$ was measured to be $3.60 MPa{\cdot}m^{1/2}$ using the single-edge V-notched beam (SEVNB) technique. The fracture mode of the nanocomposites was transgranular, in contrast to the intergranular mode of monolithic alumina. The fracture morphology suggested that dislocations were generated around the silver nanoparticles dispersed within the alumina matrix. The specimens sintered at $1350^{\circ}C$ were annealed at $800^{\circ}C$ for 5 min, following which the maximum fracture strength became 810 MPa and the fracture toughness improved to $4.21 MPam^{1/2}$. The critical FPZ size was the largest for the specimen annealed at $800^{\circ}C$ for 5 min. Thermal conductivity of the alumina/silver nanocomposites sintered at $1350^{\circ}C$ was 38 W/mK at room temperature, which was higher than the value obtained with the law of mixture.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2007년도 추계학술대회 논문집
• /
• pp.280-280
• /
• 2007

Lead oxide-based ferroelectrics are the most widely used materials for piezoelectric actuators, sensors and transducers due to their excellent piezoelectric properties. Considering lead toxicity, there is great interest in developing lead-free piezoelectric materials, which are biocompatible and environmentally friendlier. Recently alkali oxide materials, including sodium - potassium niobate (NKN), have been given attention in view of their ultrasonic application and also as promising candidates for piezoelectric lead-free system. However, it is difficult to sinter such NKN-based materials via conventional sintering process. In this reason, many researchers have investigated hot press, hot isostatic press or spark-plasma sintering of NKN-based ceramics. In this study, as candidates for lead-free piezoelectric materials, dense (Na,K,Li)(Nb,Sb)$O_3$ systems were developed by conventional sintering process. The microstructures and piezoelectric properties of the (Na,K,Li)(Nb,Sb)$O_3$ systems were investigated as a function of variable compositions. The excellent piezoelectric and electromechanical properties indicate that this system is potentially good candidate as lead-free material for a wide range of electro-mechanical transducer applications.

• Nuclear Engineering and Technology
• /
• 제46권1호
• /
• pp.117-124
• /
• 2014

The effect of various process variables on the powder properties of recycled $U_3O_8$ from MnO-$Al_2O_3$ doped large grain $UO_2$ pellets and the effect of those recycled $U_3O_8$ powders on the sintered density and grain size of MnO-$Al_2O_3$ doped large grain $UO_2$ pellets have been investigated. The evolution of morphology, size, and BET surface area of the recycled $U_3O_8$ powders according to the respective variation of the thermo-mechanical treatment variables of oxidation temperature, powder milling, and sequential cyclic heat treatment of oxidation and then reduction was examined. The correlation between the BET surface area of recycled $U_3O_8$ powder and the sintered pellet properties of MnO-$Al_2O_3$ doped pellets showed that the pellet density and grain size of doped pellets were increased and then saturated by increasing the BET surface area of the recycled $U_3O_8$ powder. The density and grain size of the pellets were maximized when the BET surface area of the recycled $U_3O_8$ powder was in the vicinity of $3m^2/g$. Among the process variables applied in this study, the cyclic heat treatment followed by low temperature oxidation was a potential process combination to obtain the sinter-active $U_3O_8$ powder.

• 한국결정성장학회지
• /
• 제32권5호
• /
• pp.205-211
• /
• 2022

GSV (Granule Spray in Vacuum)는 상온의 진공하에서 나노 크기의 치밀한 세라믹 코팅층을 형성하는 방법이다. 일반적으로, 단사정의 지르코니아는 1150℃에서 정방정으로 변태하며, 이때 6.5 %의 체적변화를 일으켜 치밀한 단사정의 지르코니아를 만들기 어렵다. 본 연구에서는 코팅 효율에 대한 두 가지 처리 변수의 효과를 조사하는 데 중점을 두었다. 아울러, 특별한 가열과정 없이 형성된 필름의 미세구조에 관찰하였다. 샘플 기판에 증착된 지르코니아 필름에 대한 X-ray diffractometer (XRD) 분석은 단사정 지르코니아 필름이 성공적으로 증착되었음을 보여주었다.