• New & Renewable Energy
• /
• v.18 no.2
• /
• pp.40-49
• /
• 2022

In this study, the phase and electrochemical properties of Co and Ti substituted layered perovskites SmBaCo_2-xTi_xO_5+d (x=0.5, 0.7, 1.0, 1.1, 1.3, and 1.5) were analyzed, and their application as electrodes in solid oxide fuel cells (SOFCs) were evaluated. After calcination at 1300℃ for 6 h, a single phase was observed for two compositions of the SmBaCo_2-xTi_xO_5+d oxide system, SmBaCoTiO_5+d (x=1.0) and SmBaCo_0.9Ti_1.1O_5+d (x=1.1). However, the phases of SmBaCoTiO_5+d (SBCTO) and SmTiO₃ coexisted for compositions with x≥1.3 (Ti content). In contrast, for compositions of x≤0.7, the SmBaCo₂O_5+d phase was observed instead of the SmTiO₃ phase. To evaluate the applicability of these materials as SOFC electrodes, the electrical conductivities were measured under various atmospheres (air, N₂, and H₂). SBCTO exhibited stable semi-conductor electrical conductivity behavior in an air and N₂ atmosphere. However, SBCTO showed insulator behavior at temperatures above 600℃ in a H₂ atmosphere. Therefore, SBCTO may only be used as cathode materials. Moreover, SBCTO had an area specific resistance (ASR) value of 0.140 Ω·cm² at 750℃.

• The Journal of the Convergence on Culture Technology
• /
• v.9 no.6
• /
• pp.855-859
• /
• 2023

Copper oxide (CuO) nanoparticles were successfully synthesized using a precursor in which industrial starch was impregnated with an aqueous solution of copper (II) nitrate trihydrate. The microstructure of the precursor impregnated with an aqueous solution of copper nitrate trihydrate was confirmed with a scanning electron microscope (SEM), and the particle size and the crystal structure of the copper oxide particles produced as the temperature of the heat treatment of the precursor increased was analyzed by X-ray diffraction (XRD) and the scanning electron microscope (SEM). As a result of the analysis, it was confirmed that the temperature at which the organic matter of the precursor is completely thermally decomposed is 450-490℃, and that the size and crystallinity of the copper oxide particles increased as the heat treatment temperature increased. The size of the copper oxide particles obtained through heat treatment at 500-800℃ during 1 hour was 100nm~2㎛. It was confirmed that the copper oxide crystalline phase is formed at a heat treatment temperature of 400℃, and only the copper oxide single phase existed up to 800℃. And it was also confirmed that the size of particles produced increased as the calcination temperature increased.

• Membrane and Water Treatment
• /
• v.15 no.3
• /
• pp.107-115
• /
• 2024

This study proposes the recycling of MVS as a value-added product for the removal of phosphate from aqueous solutions. By comparing the phosphate adsorption capacity of each calcined adsorbent at each temperature of MVS, it was determined that the optimal heat treatment temperature of MVS to improve the phosphate adsorption capacity was 800 ℃. MVS-800 suggests an adsorption mechanism through calcium phosphate precipitation. Subsequent kinetic studies with MVS-800 showed that the PFO model was more appropriate than the PSO model. In the equilibrium adsorption experiment, through the analysis of Langmuir and Freundlich models, Langmuir can provide a more appropriate explanation for the phosphate adsorption of MVS-800. This means that the adsorption of phosphate by MVS-800 is uniform over all surfaces and the adsorption consists of a single layer. Thermodynamic analysis of thermally activated MVS-800 shows that phosphate adsorption is an endothermic and involuntary reaction. MVS-800 has the highest phosphate adsorption capacity under low pH conditions. The presence of anions in phosphate adsorption reduces the phosphate adsorption capacity of MVS-800 in the order of CO 3 2-, SO 4 2-, NO 3- and Cl-. Based on experimental data to date, MVS-800 is an environmentally friendly adsorbent for recycling waste resources and is considered to be an adsorbent with high adsorption capacity for removing phosphates from aqueous solutions. This paper combines the advantages of gray predictor and AI fuzzy. The gray predictor can be used to predict whether the bear point exceeds the allowable deviation range, and then perform appropriate control corrections to accelerate the bear point to return to the boundary layer and achieve.

• Journal of the Korean Magnetics Society
• /
• v.12 no.5
• /
• pp.195-200
• /
• 2002

Low temperature sintering of Co$_2$Z type Ba ferrites with various oxide additives has been studied. Co$_2$Z phase was obtained by 2 step calcination and XRD peaks showed a good agreement with the peaks of the standard Co$_2$Z phase, except for some minor extra peaks. ZnO-B$_2$O$_3$ glass, ZnO-B$_2$O$_3$ and CuO, ZnO-B$_2$O$_3$ and Bi$_2$O$_3$, and ZnO-Bi$_2$O$_3$ glass were added to lower sintering temperatures. Specimens were sintered at the temperature range between 900 $^{\circ}C$ and 1000 $^{\circ}C$. In the single addition of ZnO-B$_2$O$_3$ glass, the specimen with 7.5 wt％ showed the highest shrinkage. Specimens with complex addition of ZnO-B$_2$O$_3$ glass with CuO or Bi$_2$O$_3$ showed higher shrinkages and initial permeabilities than single addition of ZnO-B$_2$O$_3$ glass. Shrinkages and initial permeabilities of the specimens with ZnO-Bi$_2$O$_3$ glass were higher than those of ZnO-B$_2$O$_3$ glass addition.

• Journal of the Korean Magnetics Society
• /
• v.24 no.1
• /
• pp.1-10
• /
• 2014

$Co_2Z$-type barium ferrites ($Ba_3Co_2Fe_{24}O_{41}$) were synthesized using variation method. First, M-type, $Co_2Y$-type and $Co_2Z$-type synthesized by hydrothermal method. Second, M- and Y-type precursors for synthesis of $Co_2Z$ hexaferrite by hydrothermal and ball milling method. the morphology, structure and magnetic properties of the barium ferrite particles were characterized using XRD, FESEM, VSM, impedance. As a result, Single phase of M-type and $Co_2Y$-type were obtained. Manufactured powders of M+Y ball milling, M+Y hydrothermal were similar to single phase of $Co_2Z$-type hexaferrite, all powders were obtained theoretical magnetization (50 emu/g). The largest initial permeability were obtained $Co_2Z$ hexaferrite synthesized by reagent precusor, With increasing calcination temperature was lowered the initial permeability. In another synthesis didn't almost that little change could be found.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.21 no.2
• /
• pp.70-74
• /
• 2011

[ $(Ca,Mg)_{0.15}Zr_{0.7}O_{1.7}$ ]ceramics was investigated for the application to SOFC ceramic supporter with high porosity and mechanical strength. $ZrO_2$ powder was prepared by combustion method with glycine using the solution of $ZrO(NO_3)_2{\cdot}2H_2O$ dissolved into deionized water and calcination at $800^{\circ}C$ Porous $(Ca,Mg)_{0.15}Zr_{0.7}O_{1.7}$ ceramics was prepared by sintering the mixture of prepared $ZrO_2$ powder, dolomite and carbon black at $1200{\sim}1400^{\circ}C$ for 1 h. The open porosity ofthe $(Ca,Mg)_{0.15}Zr_{0.7}O_{1.7}$ ceramics sintered at $1300^{\circ}C$ was over 30 % and increased linearly with the amount of carbon black. The crystal structure of $(Ca,Mg)_{0.15}Zr_{0.7}O_{1.7}$ ceramics consisted of single cubic phase. The open pore of this ceramics was connected continuously and distributed well on the whole. This ceramics sintered at $1300^{\circ}C$ showed the porosity from 32 to 55 % and mechanical strength from 90 MPa to 30 MPa with increasing the content of added carbon black.

• Applied Chemistry for Engineering
• /
• v.7 no.3
• /
• pp.543-553
• /
• 1996

Oxygen reduction in an alkaline fuel cell was studied by using perovskite type oxides as an oxygen electrode catalyst. The high surface area catalysts were prepared by malic acid method and had a formula of $La_{0.6}Sr_{0.4}Co_{1-x}Fe_xO_3$(x=0.00, 0.01, 0.10, 0.20, 0.35 and 0.50). From the result of XRD pattern and specific surface area due to the amount of Fe substitution and the consumption of ammonia-water, the complex formation of Fe ion with $NH_3$ was the main factor for both the phase stability of perovskite and the increase of specific surface area. Multi-step calcination was necessary to give a single phase of perovskite in catalyst precursor. The crystal structure of the catalysts was simple cubic perovskite, which was verified from the XRD patterns of the catalysts. The activity of oxygen reduction was monitored by the techniques of cyclic voltammetry, static voltage-current method, and current interruption method. The activity(current density) of oxygen reduction showed its minimum at x=0.01 and its maximum between 0.20 and 0.35 of x-value in $La_{0.6}Sr_{0.4}Co_{1-x}Fe_xO_3$. This tendency was independent of the change of surface area.

• Korean Journal of Materials Research
• /
• v.22 no.11
• /
• pp.631-635
• /
• 2012

Nickel oxide was doped with a wide range of concentrations (mol%) of Aluminum (Al) by solvothermal synthesis; single-phased nano powder of nickel oxide was generated after calcination at$900^{\circ}C$. When the concentration of Al dopant was increased, the reduced intensity was confirmed through XRD analysis. Lattice parameters of the synthesized NiO powder were decreased after treatment of the dopant; parameters were increased when the concentration of Al was over the doping limit (5 mol% Al). The binding energy of $Ni^{2+}$ was chemically shifted to $Ni^{3+}$ by doping $Al^{3+}$ ion, as confirmed by the XPS analysis. The tilted structure of the synthesized NiO with 5 mol% Al dopant and the polycrystalline structure of the $Ni_{0.75}Al_{0.25}O$ were observed by HR-TEM analysis. The electrical conductivity of the newly synthesized NiO was highly improved by Al doping in the conductivity test. The electrical conductivity values of the commercial NiO and the synthesized NiO with 5 mol% Al dopant ($Ni_{0.95}Al_{0.05}O$) were 1,400 s/cm and 2,230 s/cm at $750^{\circ}C$, respectively. However, the electrical conductivity of the synthesized NiO with 10 mol% Al dopant ($Ni_{0.9}Al_{0.1}O$) decreased due to the scattering of free-electrons caused by the large number of impurity atoms; the electrical conductivity of $Ni_{0.9}Al_{0.1}O$ was 545 s/cm at $750^{\circ}C$.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.25 no.4
• /
• pp.166-171
• /
• 2015

In this study, using solid-state and flux, $Y_3Al_5O_{12}:Er^{3+}\;(YAG:Er^{3+})$ powders were successfully synthesized at low temperatures. To analyze the crystallinity of powders according to the synthesis or non-synthesis of powders and powder calcination temperatures, X-ray diffraction (XRD) was measured. In the case of pure YAG, when YAG was analyzed using the general solid-phase method, it was calcined for 12 hours at $1400^{\circ}C$ and pure YAG phase could be obtained. But when $BaF_2$ was added to YAG, YAG was synthesized at lower temperature (1000^{\circ}C$). It was thus found that the synthesis temperature could be lowered by about $400^{\circ}C$. Also, when BaF2 with an optimal concentration was added to $YAG:Er^{3+}$, the particle shape and size according to synthesis temperatures were surveyed, and corresponding luminous intensity was discussed.

• Journal of the Korean Electrochemical Society
• /
• v.18 no.4
• /
• pp.143-149
• /
• 2015

Carbon-coated $Li_2MnSiO_4$ powders as the active materials for the cathode were synthesized by planetary ball milling and solid-state reaction, and their phase formation behavior and charge-discharge properties were investigated. Calcination temperature and atmosphere were controlled in order to obtain the ${\beta}-Li_2MnSiO_4$ phase, which was active electrochemically, and the carbon-coated $Li_2MnSiO_4$ active material powders with near single phase ${\beta}-Li_2MnSiO_4$ could be fabricated. The particles of the synthesized powders were secondary particles composed of primary ones of about 100 nm size. The carbon incorporation was essential to enable the Li ions to be inserted and extracted from $Li_2MnSiO_4$ active materials, and the initial capacity of 192 mAh/g could be obtained in the $Li_2MnSiO_4$ active materials with 4.8 wt% of carbon.