• Journal of the Korean Electrochemical Society
• /
• v.16 no.3
• /
• pp.184-189
• /
• 2013

$Ba_2SiO_4:Eu^{2+}$ ($B_2S:Eu^{2+}$) powders were prepared by firing the dry gel obtained by the sol-gel and the hybrid process (sol-gel and combustion), respectively, and their structure and luminescence were investigated. Tetraethyl orthosilicate (TEOS) was used as a Si source. The phase transition was observed with the TEOS content. With 1.2M TEOS, the powders prepared by the sol-gel process without prior calcination were composed of the $B_2S:Eu^{2+}$ single phase, whereas those by the sol-gel and the hybrid process with prior calcination consisted of the dominant $B_2S:Eu^{2+}$ and minor $BaSiO_3:Eu^{2+}$ ($BS:Eu^{2+}$) phases and their emission intensities were approximately two times higher than those without prior calcination. The hybrid process could reduce the process time innovatively compared to the sol-gel process, even though the former was a little inferior to the latter in the emission intensity of $B_2S:Eu^{2+}$. With 1.1M TEOS, the $B_2S:Eu^{2+}$ single phase was obtained by the hybrid process, and its green emission was observed at 505 nm originated from the $4f^65d^1{\rightarrow}4f^7$ transition of $Eu^{2+}$ ions.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.22 no.4
• /
• pp.194-199
• /
• 2012

The $LiMn_{1.5}Ni_{0.5}O_4$, substituting a part of Mn with Ni in the $LiMn_2O_4$, the spinel structure has good charge-discharge cycle stability and high discharge capacity at 4.7 V. In this study $LiMn_{1.5}Ni_{0.5}O_4$ powders were synthesized by polymerization complex method. The effect on the characteristics of synthesized $LiMn_{1.5}Ni_{0.5}O_4$ powders was studied with citric acid (CA) : metal ion (ME) molar ratio (5 : 1, 10 : 1, 15 : 1, 30 : 1) and calcination temperature ($500{\sim}900^{\circ}C$). Single phase of $LiMn_{1.5}Ni_{0.5}O_4$ was observed from XRD analysis on the powders calcined at low ($500^{\circ}C$) and high temperatures ($900^{\circ}C$). The crystalline size and crystallinity increased with calcination temperature. At low calcination temperature the particle size decreased and specific surface area increased as the CA molar ratio increased. On the other hand, high particle growth rate at high calcination temperature interfered the particle size reduction and specific surface area increase induced by the increase of CA molar ratio.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.7 no.4
• /
• pp.528-535
• /
• 1997

$LiTaO_3$ single crystals of congruently melting composition were grown by the halogen lamp type floating zone system. Calcination and sintering parameters for the growth were established. Optimum crystal growth conditions were investigated by a controlling of growth rates, rotation speeds and atmospheres. Based on the melting aspect and the shape of molten zone, stable conditions could not be found in air or Na atmosphere. However the growth stability in Ar atmosphere was more regular than that in air or $N_2$. The grown crystals were characterized using Laue back reflection, Curie temperature, refractive index and transmittance. Curie temperature fluctuation in the section of the grown crystal part of top, body and tail was $1^{\circ}C$.

• Journal of the Korean Ceramic Society
• /
• v.39 no.7
• /
• pp.687-692
• /
• 2002

Preparation of spherical single-perovskite phase PMN-PT powder was tried by surface modification of the precursor powder with magnesia sol. The ball-milled mixed powder was heat treated at 550$\^{C}$/l h to remove any volatiles. The calcined powder was treated with the magnesia sol of 0.3-1.0 wt% and followed by calcination at 800$\^{C}$/l h to give rise to single phase perovskite PMN-PT powders. The powder with a binary size of <0.3 ㎛ and -2 ㎛ was obtained for MgO(0.3), but the spherical, agglomerate-free powder of 0.5-0.8 ㎛ was obtained for MgO(0.6) as well as for MgO(1.0).

• Bulletin of the Korean Chemical Society
• /
• v.28 no.9
• /
• pp.1467-1471
• /
• 2007

The green-emitting CeMgAl11O19:Tb (CMAT) phosphor has been prepared at 1200 °C by the simple solid-state reaction using AlF3 as a self-flux. This preparation temperature is much lower than those (1500-1700 °C) for conventional solid-state reaction and spray pyrolysis method. In particular, the complete process to produce high-quality phosphor particles was carried out through the single-step heat treatment of the mixture of corresponding oxide-type metal sources. An addition of AlF3 as a self-flux significantly decreased the crystallization temperature of CMAT with plate-like shape. The particle morphology could be controlled from plate-like to spherical by using H3BO3 as an additional flux. Thus, an optimal morphology and luminescence characteristics of CMAT were achieved when both AlF3 and H3BO3 fluxes were simultaneously used. Compared with conventional solid-state process, which is accompanied by the calcination step(s), and other alternative liquid solution techniques such as sol-gel method and spray pyrolysis, no use of active precursors and liquid media that are harmful to the environment is a distinctive advantage for the industrial purpose.

• Journal of Magnetics
• /
• v.22 no.2
• /
• pp.169-174
• /
• 2017

In this work, lithium ferrite ($Li_{0.5}Fe_{2.5}O_4$) nanoparticles were prepared via mechanochemical processing and subsequent heat treatment at a relatively low ($600^{\circ}C$) calcining temperature. The raw materials used were high purity $Fe_2O_3$ and $Li_2CO_3$ that were milled for between 2 and 20 h. The milled powders were then calcined at temperatures of 500 and $600^{\circ}C$ for 5 h in air. XRD results show that optimum conditions to obtain single phase lithium ferrite nanoparticles with a mean crystallite size of about 23 nm, using Scherrer's formula, are 10 h milling and calcination at $600^{\circ}C$. Saturation magnetization and coercivity of the single phase Li ferrite nanoparticles are 44.6 emu/g and 100 Oe respectively, which are both smaller than those of the bulk Li ferrite. The Curie temperature of the single sample was determined by a Faraday balance, which is $578^{\circ}C$ and smaller than that of bulk Li ferrite.

• Proceedings of the KIEE Conference
• /
• 2005.07c
• /
• pp.2001-2003
• /
• 2005

Various organic acid were used in order to prepare new metalorganic deposition solution for high quality $REBa_2Cu_3O_{7-{\delta}}$ (RE=Y, Eu, Gd) films. Prepared fluorine free MO precursor solution was coated on single crystal (001) $LaAlO_3$ (LAO) by dip coating method. Processing parameters such as oxygen partial pressure, water vapor, ramping rate and pyrolysis temperature etc havebeen controlled in order to make high $J_c$ films with a good epitaxial relationship with substrate. 0.5 micron-thick film was obtained by single coating and no crack appeared after calcination. Oxygen partial pressure was varied in the range of $100{\sim}1,000 ppm$ and conversion heat treatment was carried out at the temperature of $725{\sim}765^{\circ}C$. A critical transition temperature $(T_{c0})$ of 90K and a critical transport current density $(J_c)$ of $>0.5MA/cm^2$ (77K and self-field) were demonstrated for the YBCO film on (001) oriented LAO substrates with a thickness of 0.5 micron. $I_c$ was determined by utilizing a transport measurement. SEM and XRD investigations confirmed that films were grown epitaxially onto the LAO single crystal substrate. It is thought that fluorine free new MOD solutionis promising for high quality REBCO films.

• Progress in Superconductivity
• /
• v.13 no.2
• /
• pp.133-138
• /
• 2011

To reduce the processing cost of the single grain REBCO (RE: Rare-earth elements) bulk superconductors, a cost-effective process should be developed. One possible way of developing the cost-effective process is the use of low-cost precursor powders. In this study, the single grain YBCO superconductors were fabricated using a home made powder. $YBa_2Cu_3O_{7-y}$ (Y123) powders were synthesized at $850-900^{\circ}C$ in air by the powder calcination method with repeated crushing and heat treatment steps. The processing parameters for the fabrication of single grain Y123 bulk superconductors, $T_{max}$ (maximum temperature), $T_p$ (peritectic temperature) and a cooling rate through $T_p$ were optimized. To enhance the flux pinning capacity of the single grain Y123 samples, $Y_2BaCuO_5$ (Y211) particles were dispersed in the Y123 matrix by adding $Y_2O_3$ powder to the calcined Y123 powder. Applying the optimized processing condition, the single grain Y123 superconductors with $T_c=91\;K$ and $J_c=1.5{\times}10^4\;A/cm^2$ at 2 T were successfully fabricated using a home made powder. The levitation forces and trapped magnetic field at 77 K measured using a Nd-B-Fe permanent magnet of 5300 G were 47 N and 3000 G, respectively, which are comparable to those obtained for the samples fabricated using a commercial grade Y123 powders.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.8
• /
• pp.602-610
• /
• 2012

The powders for the $Na_xWO_3$ (x= 1 and 0.75) sputtering targets were synthesized by the calcination in reductive atmosphere. Near single-phase $NaWO_3$ and single-phase $Na_{0.75}WO_3$ powder targets were prepared. By using the targets, thin films of each composition were deposited by rf magnetron sputtering on the $SiO_2$ (100 nm)/Si substrates and annealed by RTP (rapid thermal processing) for crystallization. In the case of the $NaWO_3$ composition, single-phase $Na_xWO_3$ thin films, where x was believed to be slightly less than 1, were fabricated accompanying the Na-diffusion into the substrates during RTP. However, in the case of the $Na_{0.75}WO_3$ thin film preparation, it was unable to make single-phase thin films. From the phase formation behaviors of both powders and thin films, it was revealed that $Na_xWO_3$ with nonstoichiometric composition of x, which was slightly less than 1, was favorable. The good electrical conduction properties were obtained from the single-phase $Na_xWO_3$ thin films. Their electrical resistivities were as low as $7.5{\times}10^{-4}{\Omega}{\cdot}cm$.

• Journal of the Korean Ceramic Society
• /
• v.39 no.11
• /
• pp.1113-1118
• /
• 2002

Nano sized $(Pb_{0.5}Ca_{0.5})(Fe_{0.5}Nb_{0.5})O_3$ (PCFN) powders with the stoichiometric composition and the uniform size distribution were successfully synthesized by the metal-citrate process through the calcination of the polymeric precursor which consisted of the metal ions and the organic network. The crystallization of the initial amorphous powders began at $400{\circ}$ and completed at $700{\circ}$. The pyrochlore phase was detected caused by the dissociation of PbO above $900{\circ}$. Single phase perovskite PCFN powders with 40 nm size and uniform shape were obtained through the calcination at $700{\circ}$.