• 대한전자공학회논문지SD
• /
• 제45권4호
• /
• pp.7-12
• /
• 2008

본 논문에서는 comb drive를 이용하여 수평 방향 저항 접촉 방식의 RF MEMS 스위치 개발을 소개한다. 무선통신 트랜시버에서 사용되는 FEM에서 사용될 수 있는 높은 안전성과 좋은 RF 특성을 가지는 스위치의 개발을 목표로 한다. 따라서 작은 삽입손실 특성을 가지기 위해 comb drive를 이용하여 큰 접촉 힘을 발생시키고, 큰 격리도 특성을 가지기 위해 스위치 off 상태에서 작은 정전용량을 갖도록 한다. 그리고 단결정 실리콘을 스위치의 구조물로 사용함으로써 기계적인 안전성을 갖도록 한다. 개발된 RF MEMS 스위치는 26 V의 동작 전압을 가지며, 2 GHz에서 0.44 dB 이하의 삽입손실과 60 dB 이상의 격리도 특성을 가진다.

• 한국정보처리학회논문지
• /
• 제4권1호
• /
• pp.311-323
• /
• 1997

본 논문에서는 게이트 레벌 소자와 스위치 레벨 소자가 함께 사용한 혼합형 조합 회로에서의 고착 고장(stuck-at fault) 검출을 위한 고장 시뮬레이션에 대하여 기술 한다. 실용적인 혼합형 회로의 고장 검출용으로 사용하기 위하여 게이트 레벨 및 정 적 스위치 레벨 회로는 물론 동적 스위치 레벨의 회로들도 처리할 수 있도록 한다. 또한, wired 논리 소자에서의 다중 신호 충돌 현상을 해결하기 위하여 새로운 6치 논 리값과 연산 규칙을 정의하여 신호 세기의 정보와 함께 사용한다. 고장 시뮬레이션의 기본 알고리즘으로는 게이트 레벨 조합 회로에서 주로 사용되는 병렬 패턴 단일 고장 전달(PPSFP:parallel pattern single fault propagation) 기법을 스위치 레벨 소자에 확장 적용한다. 마지막으로 스위치 레벨 소자로 구현된 ISCAS85 벤치 마크 회로와 실 제 혼합형 설계 회로에 대한 실험 결과를 통하여 본 연구에서 개발된 시스템의 효율 성을 입증한다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 추계학술대회 논문집
• /
• pp.337-340
• /
• 2007

In the dissertation, a power conversion system for fuel cell is composed of a PWM inverter with LC filter in order to convert fuel cell voltage to a single phase 220[V], In addition, new insulated DC-DC converters are proposed in order that fuel cell voltage is boosted to 380[V]. In this paper, it requires smaller components than existing converters, which makes easy control. The proposed DC-DC converter controls output power by the adjustment of phase-shift width using switch S5 and S6 in the secondary switch, which provides 93-97[%] efficiency in the wide range of output voltage. Fuel cell simulator is implemented to show similar output characteristics to actual fuel cell. Appropriate dead time td enables soft switching to the range where the peak value of excitation current in a high frequency transformer is in accordance with current in the primary circuit. Moreover, appropriate setting to serial inductance La reduces communication loss arisen at light-load generator and serge voltage arisen at a secondary switch and serial diode. Finally, TMS320C31 board and EPLD using PWM switching technique to act a single phase full-bridge inverter which is planed to make alternating current suitable for household.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2001년도 Proceedings ICPE 01 2001 International Conference on Power Electronics
• /
• pp.247-250
• /
• 2001

This paper presents a simple and cost effective circuit topology of single-ended type high frequency quasi-resonant PWM inverter using IGBTs, which can operate under wide soft switching operation range based on ZCS for main power switch as compared with a conventional active voltage-clamped ZVS-PWM high frequency quasi-resonant inverter developed previously. In principle, this new circuit topology can efficiently operate under a constant frequency PWM control-based power regulation scheme. In particular, it is noted that the zero current soft switching (ZCS) commutation can achieve for the main active power switch. On the other hand, the zero voltage soft switching (ZVS) commutation can also achieve for the auxiliary active power switch. The operating principle of this high-frequency Inverter treated here and its power regulation characteristics are illustrated on the basis of the simulation and feasible experimental results.

• 전력전자학회:학술대회논문집
• /
• 전력전자학회 2004년도 전력전자학술대회 논문집(2)
• /
• pp.723-727
• /
• 2004

A new high-performance and low cost single switch energy recovery display driver for an AC plasma display panel (PDP) is proposed. Since it is composed of only one auxiliary power switch, two small inductors, and eight diodes compared with the conventional circuit consisting of four auxiliary power switches, two small inductors, eight power diodes, and two external capacitors, it features a much simpler structure and lower cost. Nevertheless, since the rootmean-square (RMS) value of the inductor current is very small, it also has very desirable advantages such as n low conduction loss and high efficiency. Furthermore, there are no serious voltage-drops caused by the large gas-discharge current with the aid of the discharge current compensation, which can also greatly reduce the current flowing through power switches and maintain the panel to light at n lower sustaining voltage. In addition, all main power switches are turned on under the zero-voltage switching (ZVS) and thus, the proposed circuit has a improved EMI, increased reliability, and high efficiency. Therefore, the proposed circuit will be well suited to the wall hanging PDP TV. To confirm the validity of the proposed circuit, circuit operations, features,and design considerations are presented and verified experimentally on a 6-inch PDP, 50kHz-switching frequency, and sustaining voltage 141V based prototype.

• Journal of Power Electronics
• /
• 제7권2호
• /
• pp.109-117
• /
• 2007

In this paper, a novel proposal for a utility-interactive three-phase soft commutation sinewave PWM power conditioner with an auxiliary active resonant DC-link snubber is developed for fuel cell and solar power generation systems. The prototype of this power conditioner consists of a PWM boost chopper cascaded three-phase power conditioner, a single two-switch auxiliary resonant DC-link snubber with two electrolytic capacitors incorporated into one leg of a three-phase V-connection inverter and a three-phase AC power source. The proposed cost-effective utility-interactive power conditioner implements a unique design and control system with a high-frequency soft switching sinewave PWM scheme for all system switches. The operating performance of the 10 kW experimental setup including waveform quality, EMI/RFI noises and actual efficiency characteristics of the proposed power conditioner are demonstrated on the basis of the measured data.

• 대한전자공학회논문지TC
• /
• 제42권7호
• /
• pp.57-62
• /
• 2005

본 논문에서는 마이크로파 SPDT 스위치를 GaAs pHEMT 공정을 이용하여 설계 및 제작하였다. 광대역 스위치 설계를 위하여 CPW로 구현한 임피던스 변환회로를 삽입하여 온-저항과 오프-커패시턴스를 줄임으로서 낮은 삽입손실과 높은 격리도를 갖는 구조를 구현하였다. 변환회로를 구성하는 전송선로의 소자 개수와 병렬로 삽입되는 FET의 개수는 시물레이션을 통해 최적의 값으로 설계하였다. 설계된 스위치의 측정 결과 53$\~$ 61 GHz 대역에서 2.6 dB 이하의 삽입손실과 24 dB 이상의 격리도를 얻었다.

• Journal of Electrical Engineering and Technology
• /
• 제11권2호
• /
• pp.367-376
• /
• 2016

This paper presents a cell balancing method for a single switch flyback converter with a multi-winding transformer. The conventional method using a flyback converter with a multi-winding transformer is simple and easy to control, but the voltage of each secondary winding coil might be non-uniform because of the unequal effective turn-ratio. In particular, it is difficult to control the non-uniform effect using turn-ratios because secondary coil has a limited number of turns. The non-uniform secondary voltages disturb the cell balancing procedure and induce an unbalance in cell voltages. Individual cell control by adding a switch for each cell can reduce the undesirable effect. However, the circuit becomes bulky, resulting in additional loss. The proposed method here uses the conventional flyback converter with an adjustment made to the output filters of the cells, instead of the additional switch. The magnitude of voltage applied to a particular cell can be reduced or increased according to the adjusted filter and the selected switching frequency. An analysis of the conventional converter configuration and the filter design method reveals the possibility of adequate cell balancing control without any additional switch on the secondary side.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2003년도 춘계학술대회 논문집 전기기기 및 에너지변환시스템부문
• /
• pp.224-227
• /
• 2003

Single phase induction motor(SPIM) is one of the most widely used type of low power AC motors in the world, especially for domestic or commercial applications where a three phase power supply is not available. Fractional horse power of the SPIM have no starting torque their own. So there are several ways of starting SPIMS. The most common type is the starting capacitor installed in series with the auxiliary winding to increase the starting torque. Also, the auxiliary winding is disconnected once the speed of the motor reaches 70 to 80 [%] of the rated speed. In the conventional systems, this function is conducted by a centrifugal switch. But the mechanical centrifugal switch has many problems such as switch malfunction. This paper presents the starter design of SPIM capacitor starting switch using microcontroller.

• 대한전자공학회논문지SD
• /
• 제41권10호
• /
• pp.51-56
• /
• 2004

광소자의 재료물질로서 특성이 우수하며 열광학계수가 큰 silicon을 기반으로 한 SOI (Silicon-on-insulator)를 사용하여 열광학 1×2 광스위치를 제안, 제작하였다. SOI wafer는 도파로가 형성될 상위 Si 층(n=3.5)과 클래딩 영역이 될 산화막 매립층(n=1.5) 그리고 기판인 Si인 3층으로 이루어진다. BPM(Beam propagation method) 전산모의를 통해 20dB 이상의 누화특성을 갖는 단일모드의 1×2 비대칭 y-분기 광도파로를 형성하고, 열확산 전산모의를 통해 금속열선을 설계 제작하였다. 제작된 광스위치는 약 3.5 watts의 구동 전력에서 20dB 이상의 채널간 누화가 측정되었다.