• The Transactions of the Korean Institute of Power Electronics
• /
• v.17 no.1
• /
• pp.27-33
• /
• 2012

Internet Data Centers (IDC), as essential facilities for modern IT industry, typically have scores of MW of concentrated electric loads. Uninterruptible Power Supplies (UPS) are necessary for the power feed system of IDCs because of stable power requirement. Thus, conventional AC power feed systems of IDCs have three cascaded power conversion stages such as (AC-DC), (DC-AC), and (AC-DC), which results in very low conversion efficiency. On the contrary, DC power feed systems need just a single power conversion stage (AC-DC) supplying AC mains power to DC server loads, which gives comparatively high conversion efficiency and reliability. This paper compares the efficiencies between 220V AC power feed system and 300V DC power feed system on equal load conditions which were established in Mok-Dong IDC of Korea Telecom company (KT). Experimental results show that the total operation efficiency of the 300V DC power feed system is around 15% higher than that of the 220V AC power feed system.

• Steel and Composite Structures
• /
• v.17 no.6
• /
• pp.967-980
• /
• 2014

In regions of high shear forces in composite bridges, headed stud shear connectors need to be arranged with a small spacing in order to satisfy the design requirement of resisting the high interface shear force present at this location. Despite this, studies related to groups of headed studs are somewhat rare. This paper presents an investigation of the static behaviour of grouped stud shear connectors in high-strength concrete. Descriptions are given of five push-out test specimens with different arrangements of the studs that were fabricated and tested, and the failure modes, load-slip response, ultimate load capacities and related slip values that were obtained are reported. It is found that the load-slip equation given by some researchers based on a single stud shear connector in normal strength concrete do not apply to grouped stud shear connectors in high-strength concrete, and an algebraic load-slip expression is proposed based on the test results. Comparisons between the test results and the formulae provided by some national codes show that the equations for the ultimate capacity provided in these codes are conservative when used for connectors in high-strength concrete. A reduction coefficient is proposed to take into account the effect of the studs being in a group.

• Journal of the Korean Solar Energy Society
• /
• v.33 no.5
• /
• pp.34-40
• /
• 2013

Islanding phenomenon of photovoltaic system is undesirable because it leads to a safety hazard to utility service personnel and may cause damage to power generation and power supply facilities as a result of unsynchronized re-closure. Anti-islanding protection is an important technical requirement for grid-connected PV system. Until now, various anti-islanding methods for detecting and preventing islanding of photovoltaic and other distributed generations have been proposed. Most of them are focusing on the anti-islanding performance of single PV system according to the related international and domestic standard test procedures. There are few studies on the islanding phenomenon for multiple photovoltaic operation in parallel. This paper presents performance analysis of anti-islanding function for grid-connected PV inverter systems when several PV inverters are connected in parallel.

• Current Optics and Photonics
• /
• v.1 no.5
• /
• pp.538-543
• /
• 2017

Progressive addition lenses (PAL) have very wide application in the modern glasses market. The unique progressive surface can make a lens have progressive refractive power, which can meet the human eye's different needs for distance-vision and near-vision. According to the national glasses fabrication standard, the difference between actual optical power after fabrication and nominal design value should be less than 0.1D over the lens effective area. The optical power distribution of PAL is determined directly by the surface. Consequently, the surface processing accuracy requirement is proposed. Beginning from the surface expressions of progressive addition lenses, the relationship equations between the surface sag and optical power distribution are derived. They are demonstrated through tolerance analysis and test of an example progressive addition lens with addition of 2.09D (5.46D-7.55D). The example addition surface is fabricated under given accuracy by a single-point diamond ultra-precision machine. The optical power of the PAL example is tested with a focal-meter after fabrication. The optical power addition difference between test result and design nominal value is 0.09D, which is less than 0.1D. The derived relationship between the surface error and optical power is verified from the PAL example simulation and test result. It can provide theoretical tolerance analysis proof for the PAL surface fabricating process.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.12
• /
• pp.1947-1955
• /
• 1989

With the increasing complexity of cabling at sensory level in process control and manufacturing automation, field buses were introduced to replace the traditional point to point links from each sensor or acruator to its controlling equipments by a single link on which all information is transmitted seriall and multiplexed in time. In this papr, we introduce the BITBUS network as a field bus. For the service discipline of the BITBUS network, two service strategies are proposed to obtain the performance of the network. They are the equal priority cyclic service strategy and the non-equal priority cyclic service strategy. The former assigns equal priority to each node for polling and the latter assumes non-equal priority. The BITBUS network was modeled as a cyclic queueing model and it is analyzed by two methods: the Kuehn's and the Boxma's. Computer simulation was also done for the cyclic queueing model and simulation results were compared with those. Under mathematically non-analyzable environment, only the computer simulation was done. From the simulation result, in order to meet the response time requirement of 5 msec imposed by International Electrotechnical Commission when each node has the average traffic of 5000 messages/sec in manufacturing automation the number of slave nodes should be smaller than 10 at the transmission rate of 2.5 Mbps.

• Nuclear Engineering and Technology
• /
• v.52 no.10
• /
• pp.2346-2352
• /
• 2020

Dual-energy x-ray absorptiometry (DXA) is the noninvasive method to diagnose osteoporosis disease characterized by low bone mass and deterioration of bone tissue. Many global companies and research groups have developed the various DXA detectors using a direct photon-counting detector such as a cadmium zinc telluride (CZT) sensor. However, this approach using CZT sensor has some drawback such as the limitation of scalability by high cost and the loss of efficiency due to the requirement of a thin detector. In this study, a SiPM based DXA system was developed and its performance evaluated experimentally. The DXA detector was composed of a SiPM sensor coupled with a single LYSO scintillation crystal (3 × 3 × 2 ㎣). The prototype DXA detector was mounted on the dedicated front-end circuit consisting of a voltage-sensitive preamplifier, pulse shaping amplifier and constant fraction discriminator (CFD) circuit. The SiPM based DXA detector showed the 34% (at 59 keV) energy resolution with good BMD accuracy. The proposed SiPM based DXA detector showed the performance comparable to the conventional DXA detector based on CZT.

• The Korean Journal of Zoology
• /
• v.22 no.4
• /
• pp.141-152
• /
• 1979

Feline leukemia virus DNA polymerase was purified by ion-exchange and nucleic acid affinity chromatographies. The enzyme consists of a single polypeptide chain of approximately 72, 000 molecular weight as determined by both of a glycerol density gradient centrifugation and SDS-polyacrylamide gel electrophoresis. The preferred divalent cation for DNA synthesis is $Mn^2+$ on a variety of template-primers, and its optimum concentration appears to be significantly lower than reported results of other mammalian type-C viral enzymes. The divalent cation requirement for maximum activity of RNase H is similar to those of DNA polymerase. Both DNA polymerase and RNase H activities appear to reside on the same molecule as demonstrated by the copurification of both activities through various purification steps. An additional RNase H without detectible polymerase activity was generated by a limited chymotrypsin digestion. This RNase H activity was inhibited equally effectively as RNase H in the intact reverse transcriptase by antisera prepared against reverse transcriptase of feline leukemia virus. Neutralization and binding test showed that antibody binding to reverse transcriptase molecule did not completely inhibit the polymerase activity.

• Journal of the Korea Society of Computer and Information
• /
• v.12 no.1 s.45
• /
• pp.89-98
• /
• 2007

In these days, the use of context in application running on mobile devices such as PDAs and smart Phone has become a crucial requirement for several research areas, including ubiquitous computing. mobile computing. Previous middlewares which support context provisioning uses single strategy. But, this paper proposed middleware integrated multiple strategies for context provisioning, namely internal sensors-based, external infrastructure-based, and distributed provisioning in ad hoc networks. Applications can query needed context items using SQL like context query language and require context information to use different provisioning mechanisms depending on resource availability and presence of external infrastructures.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.1
• /
• pp.185-192
• /
• 2003

Recently the steel parts used at automobiles are required to be used under high stress more than ever before in need of the weight down. To achieve this requirement of a high strength steel, it must be necessary to decrease inclusion content and surface defect as like decarburization, surface roughness etc.. In this study, the surface conditions are measured to Dow the influence on fatigue properties by two cases of shot peening of two-stage shot peening and single-stage shot peening. And for this study, three kinds of spring steel (JISG4081-SUP7, SAE 9254, DON 50CrV4) are made. This study shows the outstanding improvement of fatigue properties at the case of two-stage shot peening in the rotary bending fatigue test and this is assumed to be from (1) Decreasing the surface roughness (2) Unchanging the surface hardness (3) Increasing the compressive residual stress. But, results also show fatigue failures originated at inclusion near surface, and this inclusion type is turned out to be a alumina of hish hardness.

• Korean Journal of Clinical Pharmacy
• /
• v.23 no.1
• /
• pp.71-76
• /
• 2013

Background (Purpose): The objective of this study was to investigate regulations on pharmacist and other healthcare professional license examination in Korea. Specific aim was focused on the implementation of new regulatory system governing pharmacist license examination particularly on naming of the subjects, method of the examination, and discrimination of pass or fail. Method: Laws and regulations of Korea on the examination system were retrieved from sources posted in Ministry of Government Legislation. Results: Two major regulatory differences were found between pharmacist and other healthcare professionals license examination systems. Firstly, the regulation on pharmacist license examination was ruled by the enforcement ordinance of parent law (Pharmacy Law) while it was ruled by enforcement regulation of parent law (Medical Law). Secondly, minimum grade requirement for pharmacist and other healthcare professionals was differently set up: 40% for each single subject in pharmacist and average of 40% for each group of several subjects in other healthcare professionals. Conclusion: Since pharmacist profession has drastically changed from drug-makers to drug-users during the recent decades, it is desirable to have the regulations on pharmacist license examination system amended in harmony with other laws and regulations of Korea and other major developed countries. Two-step examination for pharmacist license appears worthwhile to implement for balancing the two key functions of the pharmacist being drug-makers and drug-users.