• 한국지진공학회논문집
• /
• 제3권3호
• /
• pp.45-54
• /
• 1999

지진의 연직성분에 의해 유발된 해진시 단일개단말뚝의 거동에 관한 이전의 연구들에서 단일개단말뚝의 지지력은 완전히 감소되었으며 관내토의 폐색도 완전히 파괴된 것으로 밝혀졌다 그러나 개단말뚝이더라도 말뚝의 관입길이가 길 경우 해진에 대하여 말뚝이 안정성을 유지할수 있고 개단강관말뚝일 경우에는 비교적 관입깊이가 짧을 경우에도 해진에 대하여 안정성을 유지할 수있을 것으로 예상된었다 본 연구에서는 초세립질 포화모래지반을 담고 잇는 소형압력토조에 단일개단말뚝 2개 또는 4개의 개단무리말뚝을 관입길이 7-40m로 모델링하여 관입시켰으며 각각의 말뚝에 대하여 압축정재하시험을 실시한후 극한지지력의 약 95%의 압축하중을 재하시킨 상태에서 해진의 진동을 작용시키면서 지지력의 감소를 확인하였고 해진 작용후의 각각의 말뚝에 대하여 압축정재하시험을 실시하였다. 해진시 천해에 설치된 단일개단말뚝과 군말뚝의 지지력은 감소되지 않았다 그러나 심해에 설치된 말뚝의 안정성은 말뚝의 지중관입 깊이에 좌우되었다 즉 27m이상 관입된 단일개단말뚝의 지지력은 안정하였으며 13m이상 관입된 2개 및 4개 군말뚝은 안정하였다 그런 7m 관입된 2개 군말뚝은 파괴되었으며 7m 관입된 4개 군말뚝의 지지력은 15%만큰 저감되었다.

• 대한치과의사협회지
• /
• 제50권7호
• /
• pp.384-393
• /
• 2012

Successful treatment of a badly broken down tooth with pulpal disease depends not only on good endodontic therapy, but also on good prosthetic reconstruction of the tooth after endodontic therapy is completed. The ideal treatment of endodontically treated teeth has been widely and controversially discussed. Endocrown is a restorative option for endodontically treated teeth. Endocrown design incorporates the core and short post into the crown as a single restoration. The preparation of endocrown consists of a circular equigingival butt-joint margin and central retention cavity of the entire pulp chamber instead of employing intraradicular posts. This design significantly increases the surface area of the preparation available for cementation. It is particularly useful in young patient teeth for long-term provisional restoration and in teeth with short clinical crowns. This technique represents a promising and conservative method for the treatment of endodontically treated teeth that require long-term protection and stability. Endocrown can be considered as a feasible alternative to full crowns or composite overlays for the restoration of non vital teeth.

• 한국자동차공학회논문집
• /
• 제7권9호
• /
• pp.165-171
• /
• 1999

An oil layer fuel absorption /desorption modeling was developed. Multi-component fuel model has showed more reasonable condition than single component model. Henry's constant which is related to solubility is the most important variable in the oil layer absorption/desorption mechanism. The oil segments close to the top of the cylinder liner have more significant contribution to the fuel absorption and desorption process than other oil segments. At the warmed-up condition, the effect of the engine speed on the precent fuel absorbed/desorbed is minimal. But at low il film temperature, percent of fuel abosrbed/desorbed is decreased with increasing the engine speed because of low value of molecular diffusion coefficient of fuel. The amount of fuel trapped in the piston crevice is from 2 to 2.3 times larger than that of fuel in the oil fim. However, fuel form oil film slowly desorbs into the combustion chamber compared with fuel from the piston crevices when the engines is cold.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.184-189
• /
• 2000

Two types of fiber-optic sensors, EFPI(extrinsic Fabry-Perot interferometer) and FBG(fiber Bragg grating), have been investigated for measurement of thermal strain and temperature. The EFPI sensor is only for measurement of thermal strain and the FBG sensor is for simultaneous measurement of thermal strain and temperature. FBG temperature sensor was developed to measure strain-independent temperature. This sensor configuration consists of a single-fiber Bragg grating and capillary tube which makes it isolated from external strain. This sensor can then be used to compensate for the temperature cross sensitivity of a FBG strain sensor. These sensors are demonstrated by embedding them into a graphite/epoxy composite plate and by attaching them on aluminum rod and unsymmetric graphitelepoxy composite plate. All the tests were conducted in a thermal chamber with the temperature range $20-100^{\circ}C$. Results of strain measurements by fiber-optic sensors are compared with that from conventional resistive foil gauge attached on the surface.

• 한국유체기계학회 논문집
• /
• 제1권1호
• /
• pp.58-63
• /
• 1998

To investigate turbine flow fields under realistic conditions, a rotating turbine test facility has been developed at the Inha University Propulsion Laboratory. The experimental facility consists of an air inlet, settling chamber, single turbine stage test section, and diffuser. This turbine has a design flow coefficient of 0.55 and work coefficient of 1.88. The turbine test rig has four features. First, a large scale test section improves space resolution. Second, low speed rpm enhances safety and reduces required power, Third, DC motor/generator is able to regenerate blower power. Fourth, various types of experiment can be carried out.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.97-103
• /
• 1997

Effects of fuel injection timing on the lean misfire limit of a sequential MPI SI engine has been investigated. To investigate the interaction of injection timing and intake flow characteristics, so called axial stratification phenomena, 4 kinds of different intake swirl port of the same combustion chamber geometry have been teated in a single cylinder engine test bench. And 2 kinds of fuel, gasoline and compressed natural gas(CNG), were used to see the effect of liquid fuel vaporization. Result shows that combination of port swirl and injection timing governs the lean misfire limit and lean misfire limit envelopes remain almost the same for a given ratio regardless of engine speed. It is also found that two phase flow has some effects on lean misfire limit.

• 대한기계학회논문집B
• /
• 제21권1호
• /
• pp.36-48
• /
• 1997

In order to establish the ignition system for lean burn, the influence of the number of spark plug, spark times and spark intervals on discharge pattern of spark energy on ignitability and combustion characteristics were evaluated. It showed that, ignitability remarkably increased with the case of multiple spark ignition system than with the case of single spark and the lean limit extended fuel/air equivalence ratio by 0.1, the increase of magnitude and lasting time of capacity component and inductance component was multi spark discharge in a row.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2002년도 춘계학술대회 논문집
• /
• pp.897-900
• /
• 2002

The collimation mirror will be used for thermal vacuum testing of spacecraft. The reflection mirror system to generate parallel beam inside the thermal vacuum chamber. A 600mm diameter aspheric Collimation mirror was fabricated by ultra-precision single point diamond turning (SPDT). Aluminum alloy for mirror substrates is known to be easily machining, but not polishable due to its ductility. Aspheric large collimation reflector without a conventional polishing process, the surface roughness of 10nmRa, and the from error of $\lambda/2 ~\lambda/4(\lambda$ =632.8 nm) for reference curved surface 600 mm has been required. The purpose of this research is to find the optimum machining conditions for reflector cutting of A16061-T651 and apply the SPDT technique to the manufacturing of ultra precision optical components of metal aspheric reflector.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 추계학술대회논문집
• /
• pp.903-908
• /
• 2006

As environmental vibration requirements on precision equipment become more stringent. use of pneumatic isolators has become more popular and their performance is subsequently required to be further improved. Dynamic performance of passive pneumatic isolators is related to various design parameters in a complicated manner and, hence, is very limited especially in low frequency range by volume of chambers. In this study, an active control technique, so called time delay control which is considered to be adequate for a low frequency or nonlinear system, is applied to a single chamber pneumatic isolator. The procedure of applying the time delay control law to the pneumatic isolator is presented and its effectiveness in enhancement of transmissibility performance is shown based on simulation and experiment. Comparison between passive and active pneumatic isolators is also presented.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2009년도 추계학술대회 논문집
• /
• pp.143-143
• /
• 2009

In this paper, MgO thin films were deposited on Si(100) single crystal substrates by RF magnetron sputtering. The effects of RF power, chamber atmosphere, and substrate temperature on the characteristics of MgO thin films were already studied. Thus, we focused on the working pressure. The structural properties of the films changed dramatically with deposition conditions. Structural analyses carried out by X-ray diffraction (XRD). MgO films were obtained at the deposition conditions as follows: