• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.34 no.6
• /
• pp.416-425
• /
• 2021

In the 4^th industrial age, electronic devices are becoming smaller and lighter with a low power consumption to overcome spatial limitation. The piezoelectric energy harvesters can convert mechanical kinetic energy into electric energy; thus, enabling the operation of small electronic devices. Recently, various piezoelectric harvesters have been reported and the electric output from these harvesters could be anticipated by theoretical analysis methods. For example, COMSOL Multiphysics software provides a theoretical simulation of piezoelectric effect with a combination of mechanical and electrical phenomena in the piezoelectric materials. This article introduces a brief modeling of piezoelectric harvester to investigate mechanical stress and electrical output of harvesting devices by the COMSOL Multiphysics software.

• Journal of Power Electronics
• /
• v.13 no.6
• /
• pp.928-938
• /
• 2013

This paper proposes a novel control method for a multi-output switched-resonant converter. Output voltage can be regulated against variations in the supply voltage and load by controlling the voltage of the resonant capacitor (pulse amplitude control). Precise control is possible when pulse amplitude control is combined with pulse number control. The converter is analyzed, and design considerations are explained by using examples. Control implementation is described and load regulation and ripples are analyzed by simulation and hardware results. The topology is modified to obtain an additional negative output without any additional hardware other than a diode. The analysis of such a triple output converter with two positive outputs and one negative output is conducted and confirmed. The topology and control scheme are scalable to any number of outputs.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2004.05a
• /
• pp.452-456
• /
• 2004

A study on gust loads alleviation using aircraft control surface was performed. Aeroservoelastic model including control surface controller was formulated and validated by comparing the results of continuous turbulence response analysis with those of MSC/NASTRAN. Optimal control with output feedback was adopted for designing the control surface controller, and the effects of gust loads alleviation was validated by performing the numerical simulation for the controller designed.

• Journal of the Korea Society for Simulation
• /
• v.4 no.2
• /
• pp.69-78
• /
• 1995

Simulation is generally used for the performance analysis and optimization of manufacturing systems. Therefore in this paper using the simulation techniques we obtain the information about the efficiency improvement and the optimization. Because simulation optimization method is subjected to the applied field and environment the general simulation optimization method does not exist. So we do not take the fixed optimization procedure but suggest the alternative one which is modified for applied field. This procedure supplies the optimized simulation information and helps improve the productivity of Geared-Motor assembly line. In order to optimize the manufacturing system we use two simulation languages, FACTOR/AIM and SLAMSYSTEM. The former gives the abundant output information. The latter gives the flexibility in simulation modeling.

• Journal of the Korea Society for Simulation
• /
• v.13 no.2
• /
• pp.23-34
• /
• 2004

Regenerative simulation (RS) is a method of stochastic steady-state simulation in which output data are collected and analysed within regenerative cycles (RCs). Since data collected during consecutive RCs are independent and identically distributed, there is no problem with the initial transient period in simulated processes, which is a perennial issue of concern in all other types of steady-state simulation. In this paper, we address the issue of experimental analysis of the quality of sequential regenerative simulation in the sense of the coverage of the final confidence intervals of mean values. The ultimate purpose of this study is to determine the best version of RS to be implemented in Akaroa2 [1], a fully automated controller of distributed stochastic simulation in LAN environments.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.10 no.4
• /
• pp.184-192
• /
• 1985

The parameter regulation of proportional-plus-intergral-plus-derivative output feedback controllers is presented in the practical compter simulation and the time-domain analysis. Particularly, the restriction of parameter regulation for PID controller utilization is investigated as a result of simulation method. It is finally noted that one may resort to the design of controllers, as investigated, for rapid steady-state response, disturbance rejection, and transient response performance (over 3rd-order process) without computing the open-loop transfer functionmatrix. in consequence is presented the block diagram of sensor base system for PID output feedback controllers.

• New & Renewable Energy
• /
• v.9 no.4
• /
• pp.19-24
• /
• 2013

In order to analyze the characteristics of tidal current power generation system, we measured output power in M-G Set (Motor-Generator Set) and MATLAB/Simulink. We installed M-G Set (Motor-Generator Set) and did a simulation using MATLAB/Smulink. The simulation consisted of the tidal current turbine, PMSG, converter, and three-phase PWM inverter. Also, the speed control of the generator was performed using machine side converter. And we measured output voltage, current, power of the generator and the output power of three-phase PWM inverter.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.944-955
• /
• 2019

In this paper, the three-level T-type neutral-point-clamped indirect matrix converter topology and the relative space vector modulation methods are introduced to improve the voltage transfer ratio and output voltage performance. The presented converter topology is based on combinations of cascaded-rectifier and three-level T-type neutral-point-clamp inverter. It can overcome the limitation of voltage transfer ratio of the conventional matrix converter and the high voltage rating of power switches of conventional matrix converter. Two SVPWM strategies for proposed converter are described in this paper to achieve the advantages features such as: sinusoidal input/output currents and three-level output voltage waveforms. Results from Psim 9.0 software simulation are provided to confirm the theoretical analysis. Hence, a laboratory prototype was implemented, and the experimental results are shown to validate the simulation results and to verify the effectiveness of the proposed topology and modulation strategies.

• 제어로봇시스템학회:학술대회논문집
• /
• 2003.10a
• /
• pp.2291-2294
• /
• 2003

In this paper, analysis and control design of ac-dc converter, normally nonlinear time-varying system, using sliding mode controller to achieve fast output voltage response, disturbance rejection and robust system in the presence of load variation are demonstrated. The objective of this method is to develop methodology for output voltage to be constant and input current sinusoidal that results in nearly unity power factor, respectively. In addition the converter can be also bidirectional power flow. Simulation results using Matlab/Simulink show the effectiveness of sliding mode control system compared with linear feedback controller to guarantee enhanced PF>0.98, THD<5%, and ripple output voltage is less than 1% at the maximum output power.

• Journal of Power Electronics
• /
• v.16 no.5
• /
• pp.1802-1812
• /
• 2016

Cross regulation is a key technical issue of single-inductor multiple-output (SIMO) DC-DC converters. This paper investigates the cross regulation in single-inductor dual-output (SIDO) Buck converters with continuous conduction mode (CCM) operation. The expressions of the DC voltage gain, control to the output transfer function, cross regulation transfer function, cross coupled transfer function and impedance transfer function of the converter are presented by the time averaging equivalent circuit approach. A small signal model of a SIDO CCM Buck converter is built to analyze this cross regulation. The laws of cross regulation with respect to various load conditions are investigated. Simulation and experiment results verify the theoretical analysis. This study will be helpful for converter design to reduce the cross regulation. In addition, a control strategy to reduce cross regulation is performed.