• Journal of the Korea Safety Management & Science
• /
• v.12 no.2
• /
• pp.153-159
• /
• 2010

The air logistics process is complex and needs many informations because various agencies participate in the logistics service and many stakeholders in air logistics. But it is hard to improve the infra of facilities because of an enormous expense, so air logistics process has to simplify for growing air freight. Nevertheless some documents are same, they should be changed due to different format. Also documents have to change even though different documents have same informations. Consequently, errors are increased because the names of the same data are different from each other and stakeholders have to reproduce the documents. In order to mitigate these problems, we selected documents and analyzed document data for the interface optimization in general air logistics process. Next, we unified the data names and defined contents of data. Also we set the type of the defined data on DB type, and gave the code to the defined data. It made easy to exchange informations among the stakeholders to match documents corresponding with the defined data. Finally, the simulation of air logistics processes was performed the quantitative analysis of the data that occur in the air logistics. In conclusion, we expect to reduce the inefficiency such as reproduction of data and the errors by improving the interface of information.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.39C no.7
• /
• pp.566-572
• /
• 2014

We propose a two-way multi-hop relaying scheme improving the throughput as well as enlarging the coverage for ship-to-ship communications in multi-ship marine networks. The proposed scheme reduces the time slots required for the data exchange by designing data transmission and network coding procedures in a sophisticated way based on two-phase digital network coding. Simulation results show that the proposed two-way multi-hop relaying scheme improves the throughput of the conventional one about 5/3 times.

• Proceedings of the SAREK Conference
• /
• 2008.06a
• /
• pp.769-775
• /
• 2008

The objective of this report is to determine the difference of thermal response that grouted two different materials, and compare the simulation result of the length of total ground heat exchanger length that using the ground thermal conductivity. And also to know heat exchange variation of ground heat exchanger temperature that measured with various test depth. The result shows that the test hole grouted with water permeable material got better thermal response than grouted with water impermeable material. However, with consideration of ingnore for the initial 12 hour data, the test hole grouted with impermeable material has larger thermal conductivity than the other. By former thermal conductivity, simulated data by engineering program shows only 3.4% difference or less. This result shows that ground thermal conductivity is not the main variables for the design program of ground heat exchanger. At the cooling or heating mode, base on the depth of -150m, the ground heat exchanger has best temperature at $-90{\sim}-60m$ and than getting worse because of entering water heat exchanged with leaving water in the same hole.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.4 no.3
• /
• pp.45-54
• /
• 2000

Ignition transient is a. very rapid process lasting only in the order of 100 milliseconds and therefore it is difficult to measure all relevant ballistic properties. Numerical simulation is thus useful to quantify some of these hard to measure flow and ballistic properties. One-dimensional model was employed to study the effects of aging using simplified aging scenarios for both N-H sustainer and booster motors. Also the effects of newly designed igniter on the ignition of N-H sustainer was simulated. Radiation effects could be significant in terms of energy flux increase to the propellant surface and the energy exchange between the combustion gas itself. One dimension implementation of radiation showed significant effects for rear-mounted igniter. Implementation of radiation effects into 2-D axi-symmetric numerical model was completed and its effects on the N-H sustainer were examined. To have a reliable prediction of computer model on ignition transient, accurate chemical property data on the propellant and igniter gas are required. It was found that such property data on aged N-H motors are not available. Chemical aging model can be used to predict to some degree of accuracy effects of aging on chemical and mechanical properties. Such a model was developed, albeit 2-dimensional, to study migration of moisture through a representative solid rocket motor configuration.

• Journal of the Korea Institute of Military Science and Technology
• /
• v.21 no.6
• /
• pp.865-876
• /
• 2018

This study focuses on the operating requirements of multi-resolution modeling(MRM) in training war-game model and proposes solutions for major issues of multi-resolution interoperation between Combat21 model and tank multi-purpose simulator(TMPS). We study the operating requirements of MRM through interviews with defense M&S experts and literature surveys and report the various issues that could occur with low-resolution model Combat21 and high-resolution model TMPS linked, for example, when to switch objects, what information to exchange, what format to switch to, and how to match data resolutions. This study also addresses the purpose and concept of training using multi-resolution interoperation, role of each model included in multi-resolution interoperation, and issue of matching damage assessments when interoperated between models with different resolutions. This study will provide the common goals and directions of MRM research to MRM researchers, defense modeling & simulation organizations and practitioners.

• Atmosphere
• /
• v.29 no.4
• /
• pp.417-427
• /
• 2019

The purpose of this study is to build urban canopy model (Met Office Reading Urban Surface Exchange Scheme, MORUSES) based to Unified Model (UM) by using urban building information data in Seoul, and then to compare the improving urban canopy model simulation result with that of Seoul Automatic Weather Station (AWS) observation site data. UM-MORUSES is based on building information database in London, we performed a sensitivity experiment of UM-MOURSES model using urban building information database in Seoul. Geographic Information System (GIS) analysis of 1.5 km resolution Seoul building data is applied instead of London building information data. Frontal-area index and planar-area index of Seoul are used to calculate building height. The height of the highest building in Seoul is 40m, showing high in Yeoido-gu, Gangnam-gu and Jamsil-gu areas. The street aspect ratio is high in Gangnam-gu, and the repetition rate of buildings is lower in Eunpyeong-gu and Gangbuk-gu. UM-MORUSES model is improved to consider the building geometry parameter in Seoul. It is noticed that the Root Mean Square Error (RMSE) of wind speed is decreases from 0.8 to 0.6 m s^-1 by 25 number AWS in Seoul. The surface air temperature forecast tends to underestimate in pre-improvement model, while it is improved at night time by UM-MORUSES model. This study shows that the post-improvement UM-MORUSES model can provide detailed Seoul building information data and accurate surface air temperature and wind speed in urban region.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.7B
• /
• pp.1393-1399
• /
• 1999

In this paper, a VLSI design of the convolutional codec chip of code rate r=l/3, and constraint length K=9 is presented, which is able to correct errors of the received data when transmitted data is corrupted in channels. The circuit design mainly aimed for simple implementation. In the decoder, Viterbi algorithm with 3-bit soft-decision is employed. For information sequence updating and storage, the register exchange method is employed, where the register length is 5$\times$K(45 stages). The codec chip is designed using VHDL language and Design Analyzer and VHDL Simulator of Synopsys are used for simulation and synthesis. The chip is composed of ENCODER block, ALIGN block, BMC block, ACS block, SEL_MIN block and REG_EXCH block. The operation of the codec chip is verified though the logic simulations, where several error conditions are assumed. As a result of the timing simulation after synthesis, the decoding speed of 325.5Kbps is achieved, and 6,894 gates is used.

• Atmosphere
• /
• v.29 no.4
• /
• pp.381-390
• /
• 2019

This study investigates the impacts of urban land-use fraction and temperature advection on the urban heat island intensity over the Seoul metropolitan area using the UM (Unified Model) with the MORUSES (Met Office Reading Urban Surface Exchange Scheme) during the heat wave over the region from 2 to 8, August 2016. Two simulations are performed with two different land-use type, the urban (urban simulation) and the urban surfaces replaced with grass (rural simulation), in order to calculate the urban heat island intensity defined as the 1.5-m temperature difference between the urban and the rural simulations. The land-use type for the urban simulation is obtained from Korea Ministry of Environment (2007) land-use data after it is converted into the types used in the UM. It is found that the urban heat island intensity over high urban-fraction regions in the metropolitan area is as large as 1℃ in daytime and 3.2℃ in nighttime, i.e., the effects of urban heat island is much larger for night than day. It is also found that the magnitude of urban heat island intensity increases linearly with urban land-use fraction. Spatially, the estimated the urban heat island intensities are systematically larger in the downwind regions of the metropolitan area than in the upwind area due to the effects of temperature advection. Results of this study indicate that urban surface fraction in the city area and temperature advection play a key role in determining the spatial distribution and magnitude of urban heat island intensity.

• Journal of Korea Foundry Society
• /
• v.32 no.6
• /
• pp.276-283
• /
• 2012

This study presents the results on the changes of crucible thermal conductivity and inflow of Ar, and constructed the mathematical model about heat transfer into furnace. As process variables, simulation model was designated thermal conductivity of crucible to $0.5W{\cdot}m^{-1}{\cdot}K^{-1}$, $1W{\cdot}m^{-1}{\cdot}K^{-1}$, $2W{\cdot}m^{-1}{\cdot}K^{-1}$, $4W{\cdot}m^{-1}{\cdot}K^{-1}$, and inflow rate of Ar to 15 L/min, 30 L/min, 60 L/min. Initial condition and boundary condition were set respectively in two terms of process. Each initial conditions were set up by the preceding simulation of heat and fluid flow. The primary goal is the application of unidirectional growth of Si ingot using the result. In the result of the change of heat conductivity of crucible, the higher thermal conductivity of crucible shows the shorter solidification time and the bigger temperature difference. And the flow patterns are changed with the inflow rate of Ar. Finally, we found that the lower crucible's thermal conductivity, the better crucible is at polycrystalline Si ingot growth. But in case of Ar inflow, it is hard to say about good condition. This data will be evaluated as useful reference used in allied study or process variable control of production facilities.

• Nuclear Engineering and Technology
• /
• v.54 no.11
• /
• pp.4134-4145
• /
• 2022

The collimator is one of the high-heat-flux components used to avoid a series of vacuum and thermal problems. In this paper, the heat load distribution throughout the collimator is first calculated through experimental data, and a transient thermodynamic simulation analysis of the original model is carried out. The error of the pipe outlet temperature between the simulated and experimental values is 1.632%, indicating that the simulation result is reliable. Second, the model is optimized to improve the heat transfer performance of the collimator, including the contact mode between the pipe and the flange, the pipe material and the addition of a twisted tape in the pipe. It is concluded that the convective heat transfer coefficient of the optimized model is increased by 15.381% and the maximum wall temperature is reduced by 16.415%; thus, the heat transfer capacity of the optimized model is effectively improved. Third, to adapt the long-pulse steady-state operation of the experimental advanced superconducting Tokamak (EAST) in the future, steady-state simulations of the original and optimized collimators are carried out. The results show that the maximum temperature of the optimized model is reduced by 37.864% compared with that of the original model. The optimized model was changed as little as possible to obtain a better heat exchange structure on the premise of ensuring the consumption of the same mass flow rate of water so that the collimator can adapt to operational environments with higher heat fluxes and long pulses in the future. These research methods also provide a reference for the future design of components under high-energy and long-pulse operational conditions.