• Journal of Information Display
• /
• 제1권1호
• /
• pp.63-69
• /
• 2000

In order to improve both the level and the stability of electron emission, Mo and Co silicides were formed from Mo mono-layer and Ti/Co bi-layers on single crystal silicon field emitter arrays (FEAs), respectively. Using the slope of Fowler-Nordheim curve and tip radius measured from scanning electron microscopy (SEM), the effective work function of Mo and Co silicide FEAs were calculated to be 3.13 eV and 2.56 eV, respectively. Compared with silicon field emitters, Mo and Co silicide exhibited 10 and 34 times higher maximum emission current, 10 V and 46 V higher device failure voltage, and 6.1 and 4.8 times lower current fluctuation, respectively. Moreover, the emission currents of the silicide FEAs depending on vacuum level were almost the same in the range of $10^{-9}{\sim}10^{-6}$ torr. This result shows that silicide is robust in terms of anode current degradation due to the absorption of air molecules.

• 한국재료학회지
• /
• 제16권10호
• /
• pp.656-662
• /
• 2006

We fabricated thermal evaporated 10 nm-$Ni_xCo_{1-x}$ (x=0.2, 0.5 and 0.8) /(poly)Si films to form nanothick cobalt nickel composite silicides by a rapid thermal annealing at $700{\sim}1100^{\circ}C$ for 40 seconds. A field emission scanning electron microscope and a micro-Raman spectrometer were employed for microstructure and silicon residual stress characterization, respectively. We observed self-aligned micro-pinholes on single crystal silicon substrates silicidized at $1100^{\circ}C$. Raman silicon peak shift indicates that the residual tensile strain of $10^{-3}$ in single crystal silicon substrates existed after the silicide process. We propose thermal stress from silicide exothermic reaction and high temperature silicidation annealing may cause the pinholes. Those pinholes are expected to be avoided by lowering the silicidation temperature. Our results imply that we may use our newly proposed composite silicides to induce the appropriate strained layer in silicion substrates.

• 대한금속재료학회지
• /
• 제47권5호
• /
• pp.322-329
• /
• 2009

60 nm- and 20 nm-thick hydrogenated amorphous silicon (a-Si:H) layers were deposited on 200 nm $SiO_2/Si$ substrates using ICP-CVD (inductively coupled plasma chemical vapor deposition). A 10 nm-Ni layer was then deposited by e-beam evaporation. Finally, 10 nm-Ni/60 nm a-Si:H/200 nm-$SiO_2/Si$ and 10 nm-Ni/20 nm a-Si:H/200 nm-$SiO_2/Si$ structures were prepared. The samples were annealed by rapid thermal annealing for 40 seconds at $200{\sim}500^{\circ}C$ to produce $NiSi_x$. The resulting changes in sheet resistance, microstructure, phase, chemical composition and surface roughness were examined. The nickel silicide on a 60 nm a-Si:H substrate showed a low sheet resistance at T (temperatures) >$450^{\circ}C$. The nickel silicide on the 20 nm a-Si:H substrate showed a low sheet resistance at T > $300^{\circ}C$. HRXRD analysis revealed a phase transformation of the nickel silicide on a 60 nm a-Si:H substrate (${\delta}-Ni_2Si{\rightarrow}{\zeta}-Ni_2Si{\rightarrow}(NiSi+{\zeta}-Ni_2Si)$) at annealing temperatures of $300^{\circ}C{\rightarrow}400^{\circ}C{\rightarrow}500^{\circ}C$. The nickel silicide on the 20 nm a-Si:H substrate had a composition of ${\delta}-Ni_2Si$ with no secondary phases. Through FE-SEM and TEM analysis, the nickel silicide layer on the 60 nm a-Si:H substrate showed a 60 nm-thick silicide layer with a columnar shape, which contained both residual a-Si:H and $Ni_2Si$ layers, regardless of annealing temperatures. The nickel silicide on the 20 nm a-Si:H substrate had a uniform thickness of 40 nm with a columnar shape and no residual silicon. SPM analysis shows that the surface roughness was < 1.8 nm regardless of the a-Si:H-thickness. It was confirmed that the low temperature silicide process using a 20 nm a-Si:H substrate is more suitable for thin film transistor (TFT) active layer applications.

• 한국재료학회지
• /
• 제17권6호
• /
• pp.323-330
• /
• 2007

We fabricated thermaly evaporated 10 nmNi/(poly)Si films to investigate the energy saving property of silicides formed by rapid thermal annealing (RTA) at the temperature of $300{\sim}1200^{\circ}C$ for 40 seconds. Moreover, we fabricated $10{\sim}50$ nm-thick ITO/Si films with a rf-sputter as reference films. A four-point tester was used to investigate the sheet resistance. A transmission electron microscope (TEM) and an X-ray diffractometer were used for the determination of cross sectional microstructure and phase changes. A UV-VISNIR and FT-IR (Fourier transform infrared rays spectroscopy) were employed for near-IR and middle-IR absorbance. Through TEM analysis, we confirmed $20{\sim}70nm-thick$ silicide layers formed on the single and polycrystalline silicon substrates. Nickel silicides and ITO films on the single silicon substrates showed almost similar absorbance in near-IR region, while nickel silicides on polycrystalline silicon substrate showed superior absorbance above 850 nm near-IR region to ITO films. Nickel silicide on polycrystalline substrate also showed better absorbance in middle IR region than ITO. Our result implies that nano-thick nickel silicides may have exellent absorbing capacity in near-IR and middle-IR region.

• Transactions on Electrical and Electronic Materials
• /
• 제8권3호
• /
• pp.110-114
• /
• 2007

Dependence of the thermal stability of nickel silicide on the film stress of inter layer dielectric (ILD) layer has been investigated in this study and silicon nitride $(Si_3N_4)$ layer is used as an ILD layer. Nickel silicide was formed with a one-step rapid thermal process at $500^{\circ}C$ for 30 sec. $2000{\AA}$ thick $Si_3N_4$ layer was deposited using plasma enhanced chemical vapor deposition after the formation of Ni silicide and its stress was split from compressive stress to tensile stress by controlling the power of power sources. Stress level of each stress type was also split for thorough analysis. It is found that the thermal stability of nickel silicide strongly depends on the stress type as well as the stress level induced by the $Si_3N_4$ layer. In the case of high compressive stress, silicide agglomeration and its phase transformation from the low-resistivity nickel mono-silicide to the high-resistivity nickel di-silicide are retarded, and hence the thermal stability is obviously improved a lot. However, in the case of high tensile stress, the thermal stability shows the worst case among the stressed cases.

• 한국표면공학회지
• /
• 제27권2호
• /
• pp.83-90
• /
• 1994

We have investigated the mechanism for the abnormal oxide growth occuring during oxidation of the crystalline tungsten silicide. TEM and XPS analysis reveal the abnormaly grown oxide layer consisting of crystalline $Wo_3$ and amorphous $SiO_2$. The presence of crystalline $Wo_3$ provides a rapid diffusion of oxygen through the oxide layer. The abnormal oxide growth is mainly due to the poor quality of initial oxide layer growth on tungsten silicide. Two species such as tungsten and silicon from decomposition fo tungsten silicide as well as silicon supplied from the underlying polysilicon are the main contributors sto abnormal oxide forma-tion. Consequently, the abnormal oxidation results in the disintegration of tungsten silicide and thinning of polysilicon as well.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제13권1호
• /
• pp.22-27
• /
• 2013

Detailed study on how the plasma process during the sidewall spacer formation suppresses the formation of silicide is done. In non-patterned wafer test, it is found that both fluorocarbon reactive ion etch (RIE) and TEOS plasma-enhanced deposition processes modify the Si surface so that the silicide reaction is chemically inhibited or suppressed. In order to investigate the cause of the chemical modification, we analyze the elements on the silicon surface through Auger Electron Spectroscopy (AES). From the AES result, it is found that the carbon induces chemical modification which blocks the reaction between silicon and nickel. Thus, protecting the surface from the carbon-containing plasma process prior to nickel deposition appears critical in successful silicide formation.

• 한국태양에너지학회:학술대회논문집
• /
• 한국태양에너지학회 2009년도 춘계학술발표대회 논문집
• /
• pp.230-234
• /
• 2009

It is significant technique to increase competitiveness that solar cells have a high energy conversion efficiency and cost effectiveness. When making high efficiency crystalline Si solar cells, evaporated Ti/Pd/Ag contact system is widely used in order to reduce the electrical resistance of the contact fingers. However, the evaporation process is no applicable to mass production because high vacuum is needed. Furthermore, those metals are too expensive to be applied for terrestrial applications. Ni/Cu/Ag contact system of silicon solar cells offers a relatively inexpensive method of making electrical contact. Ni silicide formation is one of the indispensable techniques for Ni/Cu/Ag contact sytem. Ni was electroless plated on the front grid pattern, After Ni electroless plating, the cells were annealed by RTP(Rapid Thermal Process). Ni silicide(NiSi) has certain advantages over Ti silicide($TiSi_2$), lower temperature anneal, one step anneal, low resistivity, low silicon consumption, low film stress, absence of reaction between the annealing ambient. Ni/Cu/Ag metallization scheme is an important process in the direction of cost reduction for solar cells of high efficiency. In this article we shall report an investigation of rapid thermal silicidation of nickel on silngle crystalline silicon wafers in the annealing range of $350-390^{\circ}C$. The samples annealed at temperatures from 350 to $390^{\circ}C$ have been analyzed by SEM(Scanning Electron Microscopy).

• 한국산학기술학회논문지
• /
• 제8권1호
• /
• pp.25-32
• /
• 2007

코발트 니켈 합금형 실리사이드 공정에서 단결정실리콘과 다결정실리콘 기판에 자연산화막이 있는 경우 나노급 두께의 코발트 니켈 합금 금속을 증착하고 실리사이드화하는 경우의 반응 안정성을 확인하였다. 4인치 P-type(100)Si 기판 전면에 poly silicon을 입힌 기판과 single silicon 상태의 두 종류 기판을 준비하고 두께 4 nm의 자연산화막이 있는 상태에서 10 nm 코발트 니켈 합금을 니켈의 상대조성을 $10{\sim}90%$로 달리하며 열증착하였다. 통상의 600, 700, 800, 900, 1000, $1100^{\circ}C$ 각 온도에서 실리사이드화 열처리를 시행 후 잔류 합금층을 제거하고, XRD(X-ray diffraction)및 FE-SEM(Field emission scanning electron microscopy), AES(Auger electron spectroscopy)를 사용하여 실리사이드가 생겼는지 확인하였다. 마이크로라만 분석기로 실리사이드 반응시의 실리콘 층의 잔류 스트레스도 확인하였다. 자연산화막이 존재하는 경우 실리사이드 반응이 진행되지 않았고, 폴리실리콘 기판과 고온에서는 금속과 산화층의 반응잔류물이 생성되었다. 단결정 기판의 고온열처리에서는 실리사이드 반응이 없더라도 핀홀이 발생할 수 있는 정도의 열스트레스가 존재하였다. 코발트 니켈 복합실리사이드 공정에서는 자연산화막을 제거하는 공정이 필수적이었다.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.353-353
• /
• 2010

본 논문에서는 소스와 드레인의 형성에 있어서 implantation 이 아닌 silicide를 형성시켜서 최고온도 $500^{\circ}C$가 넘지않는 저온공정을 실현하였고, silicon-on-insulator (SOI) 기판이 아닌 solid phase crystallization (SPC) 결정화 방법을 이용하여 결정화 시킨 SPC-TFT 기판을 사용하였다. Silicide 의 형성은 pt를 증착하여 furnace에서 열처리를 실시하여 형성하였다.