• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1963-1967
• /
• 1996

This paper describes the analysis, design, and silicon-fabrication of a fluidic proportional amplifier, which is the most important element of fluidic logic circuits. First, FEM(finite element method) analyses were performed, using the Fluent computational fluid dynamics program, and design geometries were optimized. Then, a $40\;{\mu}m$-deep amplifier was fabricated in silicon using anisotropic dry etching.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.79-79
• /
• 1999

The varous techniques for fabrication of si or metal tip as a field emission electron source have been reported due to great potential capabilities of flat panel display application. In this report, 240nm thermal oxide was initially grown at the p-type (100) (5-25 ohm-cm) 4 inch Si wafer and 310nm Si3N4 thin layer was deposited using low pressure chemical vapor deposition technique(LPCVD). The 2 micron size dot array was photolithographically patterned. The KOH anisotropic etching of the silicon substrate was utilized to provide V-groove formation. After formation of the V-groove shape, dry oxidation at 100$0^{\circ}C$ for 600 minutes was followed. In this procedure, the orientation dependent oxide growth was performed to have a etch-mask for dry etching. The thicknesses of the grown oxides on the (111) surface and on the (100) etch stop surface were found to be ~330nm and ~90nm, respectively. The reactive ion etching by 100 watt, 9 mtorr, 40 sccm Cl2 feed gas using inductively coupled plasma (ICP) system was performed in order to etch ~90nm SiO layer on the bottom of the etch stop and to etch the Si layer on the bottom. The 300 watt RF power was connected to the substrate in order to supply ~(-500)eV. The negative ion energy would enhance the directional anisotropic etching of the Cl2 RIE. After etching, remaining thickness of the oxide on the (111) was measured to be ~130nm by scanning electron microscopy.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.07a
• /
• pp.279-282
• /
• 2001

The IBE(ion beam etching)-induced Schottky barrier variation which depends on various etching history related with ion energy, incident angle and etching time has been investigated using voltage-current, capacitance-voltage characteristics of metal-etched silicon contact and morphology of etched surface were studied using AFM(atomic force microscope). For ion beam etched n-type silicons, Schottky barrier is reduced according to ion beam energy. It can be seen that amount of donor-like positive charge created in the damaged layer is proportional to the ion energy. By contrary, for ion beam etched p-type silicons, the Schottky barrier and specific contact resistance are both increased. Not only etching time but also incident angle of ion beam has an effect on barrier height. Taping-mode AFM analysis shows increased roughness RMS(Root-Mean-Square) and depth distribution due to ion bombardment. Annealing in an N$_2$ ambient for 30 min was found to be effective in improving the diode characteristics of the etched samples and minimum annealing temperatures to recover IBE-induced barrier variation were related to ion beam energy.

• Journal of Sensor Science and Technology
• /
• v.24 no.1
• /
• pp.10-14
• /
• 2015

This paper reports the results of a study on the optimization of the etching profile, which is an important factor in deep-reactive-ion etching (DRIE), i.e., dry etching. Dry etching is the key processing step necessary for the development of the Internet of Things (IoT) and various microelectromechanical sensors (MEMS). Large-area etching (open area > 20%) under a high-frequency (HF) condition with nonoptimized processing parameters results in damage to the etched sidewall. Therefore, in this study, optimization was performed under a low-frequency (LF) condition. The HF method, which is typically used for through-silicon via (TSV) technology, applies a high etch rate and cannot be easily adapted to processes sensitive to sidewall damage. The optimal etching profile was determined by controlling various parameters for the DRIE of a large Si wafer area (open area > 20%). The optimal processing condition was derived after establishing the correlations of etch rate, uniformity, and sidewall damage on a 6-in Si wafer to the parameters of coil power, run pressure, platen power for passivation etching, and $SF_6$ gas flow rate. The processing-parameter-dependent results of the experiments performed for optimization of the etching profile in terms of etch rate, uniformity, and sidewall damage in the case of large Si area etching can be summarized as follows. When LF is applied, the platen power, coil power, and $SF_6$ should be low, whereas the run pressure has little effect on the etching performance. Under the optimal LF condition of 380 Hz, the platen power, coil power, and $SF_6$ were set at 115W, 3500W, and 700 sccm, respectively. In addition, the aforementioned standard recipe was applied as follows: run pressure of 4 Pa, $C_4F_8$ content of 400 sccm, and a gas exchange interval of $SF_6/C_4F_8=2s/3s$.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.24 no.2
• /
• pp.156-161
• /
• 2011

The present study introduces a novel wet etching technique for nanostructure fabrications which usually requires low surface roughness. Using the current method, acquired profiles were smooth even in the nanoscale, which cannot be easily achieved with conventional wet or dry etching methods. As one of the most popular single crystal silicon etchant, potassium hydroxide (KOH) solution was used as a base solvent and two additives, antimony trioxide (Sb2O3) and ethyl alcohol were employed in. Four experimental parameters, concentrations of KOH, Sb2O3, and ethyl alcohol and temperature were optimized at 60 wt.%, 0.003 wt.%, 10 v/v%, and $23^{\circ}C$, respectively. Effects of additives in KOH solution were investigated on the profiles in both (110) and (111) planes of single crystal silicon wafer. The preliminary results show that additives play a critical role to decrease etch rate significantly down to ~2 nm/min resulting in smooth side wall profiles on (111) plane and enhanced surface roughness.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2006.10a
• /
• pp.73-73
• /
• 2006

• Journal of the Korean Vacuum Society
• /
• v.19 no.2
• /
• pp.114-120
• /
• 2010

Conventional surface texturing in crystalline silicon solar cell have been use wet texturing by Alkali or Acid solution. But conventional wet texturing has the serious issue of wafer breakage by large consumption of wafer in wet solution and can not obtain the reflectance below 10% in multi crystalline silicon. Therefore it is focusing on RIE texturing, one method of dry etching. We developed large scale plasma RIE (Reactive Ion Etching) equipment which can accommodate 144 wafers (125 mm) in tray in order to provide surface texturing on the silicon wafer surface. Reflectance was controllable from 3% to 20% in crystalline silicon depending on the texture shape and height. We have achieved excellent reflectance below 4% on the weighted average (300~1,100 nm) in multi crystalline silicon using plasma texturing with gas mixture ratio such as $SF_6$, $Cl_2$, and $O_2$. The texture shape and height on the silicon wafer surface have an effect on gas chemistry, etching time, RF frequency, and so on. Excellent conversion efficiency of 16.1% is obtained in multi crystalline silicon by RIE process. In order to know the influence of RF frequency with 2 MHz and 13.56 MHz, texturing shape and conversion efficiency are compared and discussed mutually using RIE technology.

• ETRI Journal
• /
• v.27 no.4
• /
• pp.433-438
• /
• 2005

We present a new type of silicon micro-probe card using a three-dimensional probe beam of the cantilever type. It was fabricated using KOH and dry etching, a porous silicon micromachining technique, and an Au electroplating process. The cantilever-type probe beam had a thickness of $5 {\mu}m$, and a width of $50{\mu}$ and a length of $800 {\mu}m$. The probe beam for pad contact was formed by the thermal expansion coefficient difference between the films. The maximum height of the curled probe beam was $170 {\mu}m$, and an annealing process was performed for 20 min at $500^{\circ}C$. The contact resistance of the newly fabricated probe card was less than $2{\Omega}$, and its lifetime was more than 20,000 turns.

• Proceedings of the KIEE Conference
• /
• 1996.07c
• /
• pp.1977-1979
• /
• 1996

Single-crystaIline silicon diaphgrams and features are fabricated without using an etch stop process. The process involves vertical dry etching, double-sided alignment, followed by wet-chemical etching from the back side. The abvantages of this process are that $5{\sim}50{\mu}m$ diaphgrams and features can be fabricated accurately and inexpensively. In addition, since no impurity-based process is introduced, highly uniform and homogenous properties can be achieved

• Proceedings of the Korean Society Of Semiconductor Equipment Technology
• /
• 2006.10a
• /
• pp.198-201
• /
• 2006

In this paper, we fabricated drag force type and pressure difference type gas flow sensor with dry etching technology which used Deep RIE(reactive ion etching) and etching stop technology which used SOI(silicon-on-insulator). we fabricated four kinds of sensor, which are cantilever, paddle type, diaphragm, and diaphragm with orifice type. Both cantilever and paddle type flow sensors have similar sensitivity as 0.03mV/V kPa. Sensitivity of the fabricated diaphragm and diaphragm with orifice type sensor were relatively high as about 3.5mV/V kPa, 1.5mV/V kPa respectively.