• Korean Journal of Materials Research
• /
• v.17 no.2
• /
• pp.73-80
• /
• 2007

For the sub-65 nm CMOS process, it is necessary to develop a new silicide material and an accompanying process that allows the silicide to maintain a low sheet resistance and to have an enhanced thermal stability, thus providing for a wider process window. In this study, we have evaluated the property and unit process compatibility of newly proposed composite silicides. We fabricated composite silicide layers on single crystal silicon from $10nm-Ni_{1-x}Co_x/single-crystalline-Si(100),\;10nm-Ni_{1-x}Co_x/poly-crystalline-\;Si(100)$ wafers (x=0.2, 0.5, and 0.8) with the purpose of mimicking the silicides on source and drain actives and gates. Both the film structures were prepared by thermal evaporation and silicidized by rapid thermal annealing (RTA) from $700^{\circ}C\;to\;1100^{\circ}C$ for 40 seconds. The sheet resistance, cross-sectional microstructure, surface composition, were investigated using a four-point probe, a field emission scanning probe microscope, a field ion beam, an X-ray diffractometer, and an Auger electron depth profi1ing spectroscopy, respectively. Finally, our newly proposed composite silicides had a stable resistance up to $1100^{\circ}C$ and maintained it below $20{\Omega}/Sg$., while the conventional NiSi was limited to $700^{\circ}C$. All our results imply that the composite silicide made from NiCo alloy films may be a possible candidate for 65 nm-CMOS devices.

• Journal of the Korean Magnetics Society
• /
• v.2 no.1
• /
• pp.22-28
• /
• 1992

Barium ferrite thin films were reactively deposited with Fe and BaO composite targets by a facing tergects sputtering unit. When thermally oxidized silicon wafers were used as substrates, minimum substrate heating of $750^{\circ}C$ was necessary for the perfect c-axis alignment in barium ferrite films. To lower the critical substrate temperature for the good c-axis alignment, such seed layers as ZnO, ${\alpha}-Fe_{2}O_{3}$ and ${\gamma}-Fe_{2}O_{3}$ were tested. The excellent c-axis algnment of BaM was obtained at a substrate temperature of $600^{\circ}C$ on ZnO seed layer whose (002) plane was parallel to the substrate surface. The magnetic properties of the BaM film showed saturation magnetization of 295 emu/cc, perpendicular coercivity of 1.7 kOe and squareness of 0.75. Optimum deposition rate of $230\;{\AA}/min$ was obtained with the composite target and this was 5 to 20 times higher than those of other investigators with oxide targets.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2013.02a
• /
• pp.272-273
• /
• 2013

Some living thingsuse micro- or nano- structures for living in nature. Scientists and engineers made efforts to mimic them, and they succeeded in making new types of applications. They used 'Namib desert beetle' to self-filling device by moisture harvesting and 'lotus leaf' to self-cleaning device by water repelling. 'Namib desert beetle' and lotus leaf have micro-patterns on their surface, which consists of hydrophobic or hydrophilic materials [1]. Moreover, micro-patterns on the surface make self-filling or self-cleaning property enhanced because of the surface roughness. Surface roughness enhances wettability [2]. Micro-pattern is a significant factor to make the surface be functional, so we want to make new types of functional surface by micro-patterning. In this work,we make several functional micro-patterns (radial, line, and dot arrays) using maskless lithography and analyze the characteristics of each micro-pattern. In order to analyze and understand surface characteristics, micro-patterns with varying sizes are investigated. All experiments are proceeded on mr-DWL5 photo resists coated on silicon wafers in same condition. All the experiments have demonstrated good performances about hydrophobic or hydrophilic property corresponding to their material and structural combinations. In radial micro-pattern, although the surface is flat, water drops on hydrophilic radial pattern can be convergent to a middle point and water drops on hydrophobic radial pattern can be divergent from the middle point. In line array micro-pattern, water drops can roll off along only one direction in parallel with the line arrays. Such phenomena might be mainly caused by the local change of surface roughness. From these results, controlling the movement and direction of water drops is made feasible without introducing a slope, which can potentially be used for new types of applications.

• Journal of Adhesion and Interface
• /
• v.9 no.4
• /
• pp.30-33
• /
• 2008

Two polymeric interfaces with single component homo-polymers were prepared to control the orientation of block copolymer thin-film nanostructures. Poly(4-acetoxy styrene) (OH-PAS) and poly(4-methoxy styrene) (OH-PMS) which have the average chemical composition of polystyrene-block-poly(methyl methacrylate) (PS-b-PMMA) were precisely synthesized through nitroxide-mediated radical polymerization. After dehydration reactions between above polymers and SiOx layers of silicon wafers, the polymer-modified interface induced partial (30%) vertical orientation of PS-b-PMMA thin film in the case of OH-PMS and wholly parallel orientation in the case of OH-PAS. Chemical compositions of polymeric interface layers are regarded as the key parameter to control the orientation of nanostructures of block copolymer thin film.

• Korean Journal of Materials Research
• /
• v.21 no.6
• /
• pp.334-340
• /
• 2011

Saw wires have been widely used in industries to slice silicon (Si) ingots into thin wafers for semiconductor fabrication. This study investigated the microstructural and mechanical properties, such as abrasive wear and tensile properties, of a saw wire sample of 0.84 wt.% carbon steel with a 120 ${\mu}M$ diameter. The samples were subjected to heat treatment at different linear velocities of the wire during the patenting process and two different wear tests were performed, 2-body abrasive wear (grinding) and 3-body abrasive wear (rolling wear) tests. With an increasing linear velocity of the wire, the tensile strength and microhardness of the samples increased, whereas the interlamellar spacing in a pearlite structure decreased. The wear properties from the grinding and rolling wear tests exhibited an opposite tendency. The weight loss resulting from grinding was mainly affected by the tensile strength and microhardness, while the diameter loss obtained from rolling wear was affected by elongation or ductility of the samples. This result demonstrates that the wear mechanism in the 3-body wear test is much different from that for the 2-body abrasive wear test. The ultra-high tensile strength of the saw wire produced by the drawing process was attributed to the pearlite microstructure with very small interlamellar spacing as well as the high density of dislocation.

• Korean Journal of Materials Research
• /
• v.18 no.4
• /
• pp.204-210
• /
• 2008

$1.5\;{\mu}m$-thick copper films deposited on silicon wafers were successfully bonded at $415^{\circ}C$/25 kN for 40 minutes in a thermo-compression bonding method that did not involve a pre-cleaning or pre-annealing process. The original copper bonding interface disappeared and showed a homogeneous microstructure with few voids at the original bonding interface. Quantitative interfacial adhesion energies were greater than $10.4\;J/m^2$ as measured via a four-point bending test. Post-bonding annealing at a temperature that was less than $300^{\circ}C$ had only a slight effect on the bonding energy, whereas an oxygen environment significantly deteriorated the bonding energy over $400^{\circ}C$. This was most likely due to the fast growth of brittle interfacial oxides. Therefore, the annealing environment and temperature conditions greatly affect the interfacial bonding energy and reliability in Cu-Cu bonded wafer stacks.

• Journal of the Korean Vacuum Society
• /
• v.19 no.4
• /
• pp.314-318
• /
• 2010

We fabricated a plasma texturing for multi-crystalline silicon cells using reactive ion etching (RIE). Multi-crystalline Si cells have not benefited from the cost-effective wet-chemical texturing processes that reduce front surface reflectance on single-crystal wafers. Elimination of plasma damage has been achieved while keeping front reflectance to extremely low levels. We will discuss reflectance, quantum efficiency and conversion efficiency for multi-crystalline Si solar cell by each RIE process conditions.

• Proceedings of the KIEE Conference
• /
• 2006.07c
• /
• pp.1621-1622
• /
• 2006

This paper presents the effect of driving waveform for piezoelectric bend mode inkjet printhead with optimized mechanical design. Experimental and theoretical studies on the applied driving waveform versus jetting characteristic s were performed. The inkjet head has been designed to maximize the droplet velocity, minimize voltage response of the actuator and optimize the firing frequency to eject ink droplet. The head design was carried out by using mechanical simulation. The printhead has been fabricated with Si(100) and SOI wafers by MEMS process and silicon direct bonding method. To investigate how performance of the piezoelectric ceramic actuator influences on droplet diameter and droplet velocity, the method of stroboscopy was used. Also we observed the movement characteristics of PZT actuator with LDV(Laser Doppler Vibrometer) system, oscilloscope and dynamic signal analyzer. Missing nozzles caused by bubbles in chamber were monitored by their resonance frequency. Using the water based ink of viscosity of 4.8 cps and surface tension of 0.025N/m, it is possible to eject stable droplets up to 20kHz, 4.4m/s and above 8pL at the different applied driving waveforms.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.31 no.6
• /
• pp.362-366
• /
• 2018

Silicon carbide is widely used in power semiconductor devices owing to its high energy gap. In particular, Schottky barrier diode (SBD) and PiN diodes fabricated on 4H-SiC wafers are being applied to various fields such as power devices. The characteristics of SBD and PiN diodes can be extracted from C-V and I-V characteristics. The measured Schottky barrier height (SBH) was 1.23 eV in the temperature range of 298~473 K, and the average ideal factor is 1.17. The results show that the device with the Schottky contact is characterized by the theory of thermal emission. As the temperature increases, the parameters are changed and the Vth is shifted to lower voltages.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.3 no.2
• /
• pp.74-79
• /
• 2002

In the a rapid changes of the semiconductor manufacturing technologies for early 21st century, it may be safely said that a kernel of terms is the size increase of Si wafer and the size decrease of semiconductor devices. As the size of Si wafers increases and semiconductor device is miniaturized, the units of cleaning processes increases. A present cleaning technology is based upon RCA cleaning which consumes vast chemicals and ultra pure water (UPW) and is the high temperature process. Therefore, this technology gives rise to the environmental issue. To resolve this matter, candidates of advanced cleaning processes has been studied. One of them is to apply the electrolyzed water. In this work, Compared with surface on Si wafer with electrolyzed water cleaning and various chemicals cleaning, and analyzed Si wafer surface condition treated with elecoolyzed water by cleaning temperature and cleaning time. Especially. concentrate upon the contact angle. finally, contact angle on surface treated with cathode water cleaning is 17.28, and anode water cleaning is 34.1.