• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1991.10a
• /
• pp.63-67
• /
• 1991

Amorphous silicon films were deposited on glass, [100] single crystal silicon wafer with thermally grown silicon dioxide, and [100] silicon wafer substrates by Plasma Enhanced Chemical Vapor Deposition(with argon diluted silane source gas). Growth rate, UV optical band edge, and the hydrogen quantity in the amorphous silicon films have been investigated as a function of the preparation conditions by measuring film thickness, UV-absorbency, and FT-IR transmittance. The growth rate of the ${\alpha}$-Si:H films increases with increasing substrate temperture, flow rate and R.F. power density. The UV optical band edge shifts to blue with the increases in the deposition pressure. Increasing substrate temperature shifts the UV optical band edge of the films to red. Hydrogen quantity in the ${\alpha}$-Si:H films increases with an increases in the R.F. powr and decreases with an increase in the substrate temperature.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07b
• /
• pp.964-967
• /
• 2002

The effectiveness of silicon nitride SiNx surface passivation is investigated and quantified. This study adopted single-layer antireflection (SLAR) coating of SiNx for efficiency improvement of solar cell. The silicon nitride films were deposited by means of plasma enhanced chemical vapor deposition (PECVD) in planar coil reactor. The process gases used were pure ammonia and a mixture of silane and helium. The thickness and the refractive index on the films were measured by ellipsometry and chemical bonds were determined by using an FT-IR equipment. This films obtained were analyzed in term of hydrogen content, refractive index for gas flow ratio $(NH_3/SiH_4)$, and efficiency of solar cell. The polycrystalline silicon solar cells passivated by silicon nitride shows efficiency above 12.8%.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.28A no.11
• /
• pp.894-901
• /
• 1991

Contact-type linear image sensors have been fabricated by means of RF glow discharge decomposition method of silane and hydrogen mixtures. The dependences of the electrical and optical properties of these sensor on thickness, RF power, substrate temperature and ambient gas pressure have been investigated. the ITO/i-a-Si:H/Al structure film shows photosensitivity of 0.85 and photocurrent to dark current ratio ($I_{ph}/I_{d}$) of 150 at 5V bias voltage under 200${\mu}W/cm^[2}$ red light intensity. Under 200${\mu}W/cm^[2}$ green light intensity, the ratio is 100. In order to investigate photocarrier transport mechanism and to obtain ${\mu}{\gamma}$ product we have measured the I-V characteristics of these sensors favricated with several different deposition parameters under various light sources. The linear inage sensor for document reading has been operated under reverse bias condition with green light source, resulting in ${\mu}{\gamma}$ product of about 1.5$[\times}10^{-9}cm^{2}$/V.

• Proceedings of the KIEE Conference
• /
• 1989.07a
• /
• pp.662-666
• /
• 1989

Pure mono Silane(Purity: 99.99%) was used as a thin film source and [$SiH_4$ + $H_2$ (5%)] + [$PH_3$ + $H_2$(0.05%)] mixed dilute gas was used for p-n junction diode. The substrate was P-type silicon wafer (p=$3{\Omega}$ cm) with the direction (100). The crystalline qualities of deposited thin film were investigated by the X-ray diffraction, RHEED and TED patterns and the voltampere characteristics of p-n junction diode was identified by I-V curve.

• Journal of the Korean Vacuum Society
• /
• v.1 no.1
• /
• pp.153-161
• /
• 1992

A plasma has been used in a high vaccum, cold wall reactor for low temperature deposition of C54 TiSi2 and for in-situ surface cleaning prior to silicide deposition. SiH4 and TiCl4 were used as the silicon and titanium sources, respectively. The deposited films had low resistivities in the range of 15~25 uohm-cm. The investigation of the experimental variables' effects on the growth of silicide and its concomitant silicon consumption revealed that and were the dominant species for silicide formation and the primary factors in silicon consumption were gas composition ratio and temperature. Increasing silane flow rate from 6 to 9 sccm decreased silicon consumption from 1500 A/min to less than 30 A/min. Furthermore, decreasing the temperature from 650 to $590^{\circ}C$ achieved blanket silicide deposition with no silicon consumption. A kinetic model of silicon consumption is proposed to understand the fundamental mechanism responsible for the dependence of silicon consumption on SiH4 flow rate.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.05b
• /
• pp.66-69
• /
• 2002

This paper presents deposition and characterizations of microcrystalline silicon$({\mu}c-Si:H)$ films prepared by hot wire chemical vapor deposition at substrate temperature below $300^{\circ}C$. The $SiH_{4}$ concentration$[F(SiH_{4})/F(SiH_{4})+F(H_{2})]$ is critical parameter for the formation of Si films with microcrystalline phase. At 6% of silane concentration, deposited intrinsic ${\mu}c-Si:H$ films shows sufficiently low dark conductivity and high photo sensitivity for solar cell applications. P-type ${\mu}c-Si:H$ films deposited by Hot-Wire CVD also shows good electrical properties by varying the rate of $B_{2}H_{6}$ to $SiH_{4}$ gas. The solar cells with structure of Al/nip ${\mu}c-Si:H$/TCO/glass was fabricated with single chamber Hot-Wire CVD. About 3% solar efficiency was obtained and applicability of HWCVD for thin film solar cells was proven in this research.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.387-390
• /
• 2002

This paper presents deposition and characterizations of microcrystalline silicon(${\mu}$c-Si:H) films prepared by hot wire chemical vapor deposition at substrate temperature below 300$^{\circ}C$. The SiH$_4$ concentration[F(SiH$_4$)/F(SiH$_4$).+(H$_2$)] is critical parameter for the formation of Si films with microcrystalline phase. At 6% of silane concentration, deposited intrinsic ${\mu}$c-Si:H films shows sufficiently low dark conductivity and high photo sensitivity for solar cell applications. P-type ${\mu}$c-S:H films deposited by Hot-Wire CVD also shows good electrical properties by varying the rate of B$_2$H$\_$6/ to SiH$_4$ gas. The solar cells with structure of Al/nip ${\mu}$c-Si:H/TCO/g1ass was fabricated with single chamber Hot-Wire CVD. About 3% solar efficiency was obtained and applicability of HWCVD for thin film solar cells was proven in this research.

• Transactions on Electrical and Electronic Materials
• /
• v.9 no.1
• /
• pp.28-32
• /
• 2008

Hydrogenated microcrystalline silicon(${\mu}c$-Si:H) films were prepared using inductively coupled plasma chemical vapor deposition(ICP-CVD) method, electrical and optical properties of these films were studied as a function of silane concentration. And then, effect of $PH_3\;and\;B_2H_6$ addition on their electrical properties was also investigated for solar cell application. Characterization of these films from X-ray diffraction revealed that the conductive film exists in microcrystalline phase embedded in an amorphous network. At $PH_3/SiH_4$ gas ratio of $0.9{\times}10^{-3}$, dark conductivity has a maximum value of ${\sim}18.5S/cm$ and optical bandgap also a maximum value of ${\sim}2.39eV$. Boron-doped ${\mu}c$-Si:H films, satisfied with p-layer of solar cell, could be obtained at ${\sim}10^{-2}\;of\;B_2H_6/SiH_4$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2014.02a
• /
• pp.369.2-369.2
• /
• 2014

Diamond-like Carbon(DLC) films doping Si were deposited by linear ion source(LIS)-physical vapor deposition method on Si wafer. We have studied the effects of Si content on friction and wear properties of DLC films and the characteristics of the films were investigated using Nano-indentation, Micro raman spectroscopy, Field Emission-Scanning Electron Microscope (FM-SEM) and X-ray Photoelectron Spectroscopy (XPS). The films has been various low-friction and low-stress by varying the flow rates of silane gas. Under the about 2% of Si doping is very suitable for improving the adhesion of films and reducing internal stress while maintaining the surfaces hardness of DLC films. Linear ion source (LIS)를 사용하여 Si wafer위에 Si 이온이 첨가된 DLC 박막을 증착하였다. 참가된Si 이온의 양에 따라 DLC 박막에 미치는 영향을 분석하기 위하여 마찰 계수 및 경도를 비교하였고, Micro raman spectroscopy, Field Emission-Scanning Electron Microscope (FM-SEM) and X-ray Photoelectron Spectroscopy (XPS)를 통하여 표면 상태를 분석하였다. 천체 주입된 가스량의 약 2%까지 Si 이온 주입이 늘어날수록 DLC 박막의 마찰계수는 낮아졌고, 경도는 Si 이온이 주입되지 않았을 경우와 비슷한 값(약 20~23 GPa)을 가졌다. 2% 이상의 주입량에서는 마찰계수는 주입량이 늘어날수록 높아졌으며 경도는 떨어지는 경향을 보였다. 이는 Si이온이 2%이하로 첨가되었을 경우, DLC 박막의 생성시 탄소 이온들의 결합 Stress를 줄여 마찰계수가 줄어든다고 볼 수 있으며, 그 양이 2%이상이 되면 오히려 불순물로 작용하여 DLC 박막의 Stress는 급격히 증가하고 마찰계수도 높아짐을 알 수 있다.

• Journal of Biomedical Engineering Research
• /
• v.8 no.1
• /
• pp.29-40
• /
• 1987

2-Hydroxyethyl methacrylate(HEMA) was copolymerized with allyltrimethylsilane- (ATMS) and allylt.imethoxysilane(ATMOS) at 70。C in N, N'dimethylformamide- (DMV) using $\alpha$ , $\alpha$'-azobisisobutyronitrile(AIBN). The compositions of unreacted monomers were determined by gas chromatographic analysis. The monomer reactivity ratios were determined by Fireman-Ross, Helen-Tiidus and intersection methods. The average values are as follows : $$r_1(HEMA) : 6.62 $\pm$ 0.07, r_2(ATMS) : 0.07 $\pm$ 0.01 for HEMA-ATMS system.$$ $$r_l(HEMA) : 4.09 $\pm$ 0.14, r_2(ATMOS) : 0.06 $\pm$ 0.01 for HEMA-ATMOS toys tem.$$ The lower rl(HEMA) In the HEMA-ATMOS system as compared to HEMA ATMS system may be contributed to higher relative reactivity of ATMOS toward the poly(HEMA) radical. The compositions of synthesized copolymers were determined from silicon con tents estimated gravimetrically. The thermal stabilities of the copolymers were investigated by thermogravimetry(TG). The enthalpic changes associated with the endothermic transition were evaluated by differential scanning calorimetry(DSC). The swelling properties of the copolymers in water were also investigated.