• Journal of Satellite, Information and Communications
• /
• v.8 no.4
• /
• pp.37-42
• /
• 2013

In this paper, we propose a compensation method of a non-ideal antenna array and a computationally efficient estimation method of the direction of arrival (DOA) for the antenna array. For DOA estimation, an antenna array is essential. By using the phase difference between the output signals of antennas, we can derive the DOA. In practice, however, mutual coupling between the elements of an antenna array change the beam pattern of each element and degrade the performance of DOA estimation. In the proposed method, we first estimate the DOA for the mid-subarray of the array, where all elements undergo relatively same coupling effect. We use the estimation of signal parameters via rotational invariance techniques (ESPRIT) algorithm to estimate the DOA. Then, we expand the array based on the estimated DOA by compensating the coupling effect. Simulation results show that the proposed method is effective when jamming to noise power ratio (JNR)is relative low.

• Journal of Digital Convergence
• /
• v.20 no.1
• /
• pp.185-190
• /
• 2022

Bluetooth is a common wireless technology that is widely used as a connection medium between various consumer electronic devices. The Bluetooth receiver usually adopts a Viterbi algorithm to improve signal-to-noise ratio performance, but requires complex hardware and calculations for continuous search and estimation for the irrational modulation indexes at the transmission. This paper proposes a non-coherent maximum estimation based 8-State Viterbi FSM to solve these complexity problems. The proposed optimal Viterbi FSM can detect Gaussian frequency-shfit keying symbol without any prior information and estimation for the modulation indexes. The HV1/HV2 packets are used for the estimation of the proposed algorithm and the simulation results have shown performance improvements with about 2dB for 10^-3 BER compared to other ideal approaches such as decision direct method.

• Geophysics and Geophysical Exploration
• /
• v.21 no.1
• /
• pp.54-60
• /
• 2018

The data acquired from seismic exploration can be used to detect the existence of oil and gas resources through appropriate processing and interpretation. The seismic attributes indicating the existence of resources are extracted from amplitude information, where the Q-factor representing intrinsic attenuation plays an useful role of hydrocarbon indicator. So, the accuracy of Q-factor estimation is very important to investigate the existence of resources. In this study, we calculated the Q-factor and analyzed the error rate through a numerical example. To mimic real data, random noise was added to the synthetic data. With the noise-added data, the Q-factor was estimated and the error rate was analyzed by using the spectral ratio method (SRM) and peak frequency shift method (PFSM). Both methods provided a relatively accurate Q-factor when the signal-to-noise ratio was 90 dB. However, the peak frequency shift method (PFSM) produced better results than the spectral ratio method (SRM) as the level of random noise increased.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.4
• /
• pp.6-14
• /
• 2011

The fast growing of the number of users requires the development of reliable communication systems able to provide higher data rates. In order to meet those requirements, techniques such as Multiple Input Multiple Out (MIMO) and Orthogonal Frequency Division multiplexing (OFDM) have been developed in the recent years. In order to combine the benefits of both techniques, the research activity is currently focused on MIMO-OFDM systems. In addition, for a fast wireless channel environment, the data rate and reliability can be optimized by setting the modulation and coding adaptively according to the channel conditions; and using sub-carrier frequency, and power allocation techniques. Depending on how accurate the feedback-based system obtain the channel state information (CSI) and feed it back to the transmitter without delay, the overall system performance would be poor or optimal. In this paper, we propose a Signal to Noise Ratio (SNR) estimation algorithm where the preamble is known for both sides of the transciever. Through simulations made over several channel environments, we prove that our proposed SNR estimation algorithm is more accurate compared with the traditional SNR estimation. Also, We applied AMC on several channel environments using the parameters of IEEE 802.11n, and compared the Throughput performance when using each of the different SNR Estimation Algorithms. The results obtained in the simulation confirm that the proposed algorithm produces the highest Throughput performance.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.14 no.4
• /
• pp.959-966
• /
• 2010

Quantitative ultrasound analysis provides fundamental information of various ultrasound parameters using spectral information of the short-gated radiofrequency(RF) data. Therefore, accurate extraction of spectral information from backscattered RF signal is crucial for further analysis of medical ultrasound parameters. In this paper, we propose two techniques for calculating a more accurate power spectrum which are based on the phase-compensation using the normalized cross-correlation to minimize estimation errors due to phase variations, and the weighted averaging technique to maximize the signal-to-noise ratio(SNR). The simulation results demonstrate that the proposed method estimates better results with 10% smaller estimation variances compared to the conventional methods.

• Proceedings of the IEEK Conference
• /
• 2005.11a
• /
• pp.93-96
• /
• 2005

We propose a computationally efficient sphere decoding (SD) algorithm with smart radius control (SRC). As a baseline algorithm for SD, we consider the modified Schnorr-Euchner (SE) algorithm [1] (hereafter, called as the MSE algorithm). In principle, the radius after zero-forcing decision feedback equalization (ZF-DFE) estimation can be reduced further if we select a new lattice vector closer to the received signal vector than the lattice vector corresponding to the ZF-DFE estimate does. In our case, we obtain such a better lattice vector by performing a sequence of alternating one-dimensional searches, starting from the ZF-DFE estimate. We then develop a novel SRC algorithm that adopts adaptively the additional radius reduction process according to the estimated signal-to-noise-power ratio (SNR) after ZF-DFE estimation. In addition, we analyze the effect of detection ordering on the complexity for SD. Column-norm ordering of the channel matrix and optimal ordering [1] are considered here. From our analyses, we see that SRC can reduce greatly the complexity for SD and the degree of complexity reduction gets significant as the SNR decreases, irrespective of detection ordering schemes used.

• Journal of Broadcast Engineering
• /
• v.8 no.2
• /
• pp.136-145
• /
• 2003

This paper proposes a DTV receiver using beamforming techniques to improve indoor and mobile reception. The proposed DTV receiver estimates the directions of arrival (DOAs) of incoming signals using Capon's DOA estimation method and generates an adaptive antenna beam pattern to the estimated DOA of the mainpath signal to Improve the channel condition. After beamforming, a following decision feedback equalizer (DFE) removes the remaining multipath components. The proposed receiver can be implemented with a conventional DTV receiver without anymodification. The performance of the proposed receiver is analyzed with modified Brazilian field test models, which include DOA information of Incoming signals. Simulation results show that the proposed receiver can satisfy the threshold of visibility (TOV) when input signal to noise ratio is slightly over 10 dB.

• The Transactions of the Korean Institute of Electrical Engineers D
• /
• v.53 no.1
• /
• pp.55-64
• /
• 2004

Conventional bipolar surface electromyography(EMG) technique detects only the superimposed electromyographic activity of a large number of motor units due to its low spatial resolution. For the diagnosis of neuromuscular disorder, the information of single MU is required. In this paper, 9 channel array surface electrode system was as designed and MLoG filter was proposed. Also the MCPT(modified convolution processing technique)method was proposed for the improvement of MUAP resolution. For performance evaluation, power spectrum analysis of random data and raw EMG signal comparison of MUAP shape and quantitative estimation of SNR were executed. As a result, the MUAP resolution improvement of 32％ was obtained from the standpoint of the signal-to-noise ratio(SNR).

• Journal of the Korea Institute of Military Science and Technology
• /
• v.5 no.2
• /
• pp.169-184
• /
• 2002

In order to extract bearing information from the directional sensors of DIFAR(directional frequency analysis and recording) that is a kind of passive sonobuoy, the cardioid beamforming algorithm applicable to DIFAR system was studied in the frequency domain. the algorithm uses narrow-band signals propagated though the media from the acoustic sources such as ship machineries. The proposed algorithm is expected to give signal to noise ratio of 6dB when it uses the maximum response axis(MRA) among the Cardioid beams. The estimated bearings agree very well with those from GPS data. Assuming the bearings from GPS data to be real values, the estimation errors are analyzed statistically. The histogram of estimation errors in each frequency have Gaussian shape, the mean and standard deviation dropping in the ranges -1.1~$6.7^{\circ}$ and 13.3~$43.6^{\circ}$, respectively. Estimation errors are caused by SMR degradation due to propagation loss between the source and receiver, daily fluctuating geo-magnetic fields, and non-stationary background noises. If multiple DIFAR systems are employed, in addition to bearing, range information could be estimated and finally localization or tracking of a target is possible.

• Investigative Magnetic Resonance Imaging
• /
• v.18 no.4
• /
• pp.303-313
• /
• 2014

Purpose : In-vivo conductivity reconstruction using transmit field ($B_1{^+}$) information of MRI was proposed. We assessed the accuracy of conductivity reconstruction in the presence of statistical noise in complex $B_1{^+}$ map and provided a parametric model of the conductivity-to-noise ratio value. Materials and Methods: The $B_1{^+}$ distribution was simulated for a cylindrical phantom model. By adding complex Gaussian noise to the simulated $B_1{^+}$ map, quantitative conductivity estimation error was evaluated. The quantitative evaluation process was repeated over several different parameters such as Larmor frequency, object radius and SNR of $B_1{^+}$ map. A parametric model for the conductivity-to-noise ratio was developed according to these various parameters. Results: According to the simulation results, conductivity estimation is more sensitive to statistical noise in $B_1{^+}$ phase than to noise in $B_1{^+}$ magnitude. The conductivity estimate of the object of interest does not depend on the external object surrounding it. The conductivity-to-noise ratio is proportional to the signal-to-noise ratio of the $B_1{^+}$ map, Larmor frequency, the conductivity value itself and the number of averaged pixels. To estimate accurate conductivity value of the targeted tissue, SNR of $B_1{^+}$ map and adequate filtering size have to be taken into account for conductivity reconstruction process. In addition, the simulation result was verified at 3T conventional MRI scanner. Conclusion: Through all these relationships, quantitative conductivity estimation error due to statistical noise in $B_1{^+}$ map is modeled. By using this model, further issues regarding filtering and reconstruction algorithms can be investigated for MREPT.