• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.10 no.5
• /
• pp.910-920
• /
• 2006

We consider the problem of estimating a code-timing of DS-CDMA signal in antenna array systems in the presence of flat fading channels and near-far environments. We derive an approximate maximum likelihood algorithm of estimating the code-timing of a desired user for DS-CDMA systems to better utilize the time-varying characteristics of the fading process. In the development of code timing estimator, the given observation bits are divided into many sets of sub-windows with each sufficiently large. The proposed method uses sub-windows with equal size associated with the coherence time of channel fading. The alternative approach is that without the estimation of the fading rate, the sufficiently given observation bits are simply separated into two consecutive sets of sub-windows. The derivation of the proposed algorithms is based on multiple antennas partially correlated in space. The impacts of spatial fading correlation on acquisition and men acquisition time performance of the proposed algorithms are also examined.

• Journal of Advanced Navigation Technology
• /
• v.27 no.6
• /
• pp.849-854
• /
• 2023

In this paper, a high-efficiency power amplifier was designed by applying the operating point Class J using LDMOS(laterally diffused metal oxide semiconductor) and optimizing the output matching circuit so that the second harmonic impedance becomes the reactance impedance. The designed power amplifier has a frequency of 108 ~ 110 MHz, Characteristics of PAE(power added efficiency) is 71.5% at P_SAT output (54.5 dBm), 55.5% at P_1dB output (51.5 dBm), and 24.38% at 45 dBm. The CSB(carrier with sideband) amplifier, which is the reference signal in the spatial modulation method, has an operating output of 45 dBm ~ 35 dBm, and linear SDM(sum in the depth of modulation) characteristics(40% ± 0.3%) were obtained. We measure the characteristics in amplitude modulation according to the bias operating point of the power amplifier for CSB and propose the optimal operating point to obtain linear modulation characteristics.

• International Journal of Computer Science & Network Security
• /
• v.23 no.10
• /
• pp.1-10
• /
• 2023

This paper proposes a method to extend Inter-Carrier Interference (ICI) canceling Orthogonal Frequency Division Multiplexing (OFDM) receivers for 5G mobile systems to spatial multiplexing 2×2 MIMO (Multiple Input Multiple Output) systems to support high-speed ground transportation services by linear motor cars traveling at 500 km/h. In Japan, linear-motor high-speed ground transportation service is scheduled to begin in 2027. To expand the coverage area of base stations, 5G mobile systems in high-speed moving trains will have multiple base station antennas transmitting the same downlink (DL) signal, forming an expanded cell size along the train rails. 5G terminals in a fast-moving train can cause the forward and backward antenna signals to be Doppler-shifted in opposite directions, so the receiver in the train may have trouble estimating the exact channel transfer function (CTF) for demodulation. A receiver in such high-speed train sees the transmission channel which is composed of multiple Doppler-shifted propagation paths. Then, a loss of sub-carrier orthogonality due to Doppler-spread channels causes ICI. The ICI Canceller is realized by the following three steps. First, using the Demodulation Reference Symbol (DMRS) pilot signals, it analyzes three parameters such as attenuation, relative delay, and Doppler-shift of each multi-path component. Secondly, based on the sets of three parameters, Channel Transfer Function (CTF) of sender sub-carrier number n to receiver sub-carrier number l is generated. In case of n≠l, the CTF corresponds to ICI factor. Thirdly, since ICI factor is obtained, by applying ICI reverse operation by Multi-Tap Equalizer, ICI canceling can be realized. ICI canceling performance has been simulated assuming severe channel condition such as 500 km/h, 8 path reverse Doppler Shift for QPSK, 16QAM, 64QAM and 256QAM modulations. In particular, 2×2MIMO QPSK and 16QAM modulation schemes, BER (Bit Error Rate) improvement was observed when the number of taps in the multi-tap equalizer was set to 31 or more taps, at a moving speed of 500 km/h and in an 8-pass reverse doppler shift environment.

• IEIE Transactions on Smart Processing and Computing
• /
• v.2 no.6
• /
• pp.345-349
• /
• 2013

This paper proposes a simplified generalized residual prediction (GRP) that reduces the computational complexity of spatial scalability in scalable high efficiency video coding (SHVC). GRP is a coding tool to improve the inter prediction by adding a residual signal to the inter predictor. The residual signal was created by carrying out motion compensation (MC) of both the enhancement layer (EL) and up-sampled reference layer (RL) with the motion vector (MV) of the EL. In the MC process, interpolation of the EL and the up-sampled RL are required when the MV of the EL has sub-pel accuracy. Because the up-sampled RL has few high frequency components, interpolation of the up-sampled RL does not give significantly new information. Therefore, the proposed method reduces the computational complexity of the GRP by skipping the interpolation of the up-sampled RL. The experiment on SHVC software (SHM-2.0) showed that the proposed method reduces the decoding time by 10 % compared to conventional GRP. The BD-rate loss of the proposed method was as low as 1.0% on the top of SHM-2.0.

• Journal of the Korean Institute of Gas
• /
• v.27 no.1
• /
• pp.70-77
• /
• 2023

Air environment regulations have been strengthened due to increasing air pollutant emissions, the target of reducing emissions has increased and interest in gas measurement methods is also increasing. The sampling method is mainly used, but due to the spatial and temporal measurement limitations, the laser absorption spectroscopy which is a real-time and in-situ method is in the spotlight. In this study, we studied the wavelength modulation spectroscopy and described the calibration-free algorithm. The developed algorithm was modified to reflect 46 multi-absorption lines and was applied to light absorption signal analysis in visible and mid-infrared regions. In addition, the difference between the modulation parameters of laser was analyzed. As a result of reviewing the performance through O₂ and NO gas measurement experiments of various concentration conditions, the linearity was R²_O2=0.99999 and R²_NO=0.99967.

• Korean Journal of Remote Sensing
• /
• v.35 no.2
• /
• pp.289-298
• /
• 2019

In this present study, the effects of Signal to Noise Ratio (SNR), Full Width Half Maximum (FWHM), Aerosol Optical Depth (AOD), $O_3$ Vertical Column Density ($O_3$ VCD), and Solar Zenith Angle (SZA) on the accuracy of sulfur dioxide Vertical Column Density ($SO_2$ VCD) retrieval have been quantified using the Differential Optical Absorption Spectroscopy (DOAS) method with the ground-based direct-sun synthetic radiances. The synthetic radiances produced based on the Beer-Lambert-Bouguer law without consideration of the diffuse effect. In the SNR condition of 650 (1300) with FWHM = 0.6 nm, AOD = 0.2, $O_3$ VCD = 300 DU, and $SZA=30^{\circ}$, the Absolute Percentage Difference (APD) between the true $SO_2$ VCD values and those retrieved ranges from 80% (28%) to 16% (5%) for the $SO_2$ VCD of $8.1{\times}10^{15}$ and $2.7{\times}10^{16}molecules\;cm^{-2}$, respectively. For an FWHM of 0.2 nm (1.0 nm) with the $SO_2$ VCD values equal to or greater than $2.7{\times}10^{16}molecules\;cm^{-2}$, the APD ranges from 6.4% (29%) to 6.2% (10%). Additionally, when FWHM, SZA, AOD, and $O_3$ VCD values increase, APDs tend to be large. On the other hand, SNR values increase, APDs are found to decrease. Eventually, it is revealed that the effects of FWHM and SZA on $SO_2$ VCD retrieval accuracy are larger than those of $O_3$ VCD and AOD. The SZA effects on the reduction of $SO_2$ VCD retrieval accuracy is found to be dominant over the that of FWHM for the condition of $SO_2$ VCD larger than $2.7{\times}10^{16}molecules\;cm^{-2}$.

• Journal of Korean Society for Geospatial Information Science
• /
• v.16 no.3
• /
• pp.43-49
• /
• 2008

The Real Time Location System (RTLS) is very important in the ubiquitous society for real time tracking of men, high price assets, and logistics products. In this work, we developed an active RF system for RTLS and tested its performance. The RTLS system developed in this work was constructed of three active readers and one active tag. The small size tag developed in this work operated with a coin type battery. To make the tag smaller, we used an internal PCB antenna and a chip antenna. We tested the performance of the tag. To reduce the manufacturing cost of our RF system, we used low price RF transceiver CC2510 chip-set. The CC2510 chip-set provided RSSI(Received Signal Strength Indicator) signal which could be used to determine the distances between an active tag and three active readers.

• Journal of Korea Society of Digital Industry and Information Management
• /
• v.9 no.1
• /
• pp.165-176
• /
• 2013

This paper introduces the high density discrete wavelet transform using quincunx sampling, which is a discrete wavelet transformation that combines the high density discrete transformation and non-separable processing method, each of which has its own characteristics and advantages. The high density discrete wavelet transformation is one that expands an N point signal to M transform coefficients with M > N. The high density discrete wavelet transformation is a new set of dyadic wavelet transformation with two generators. The construction provides a higher sampling in both time and frequency. This new transform is approximately shift-invariant and has intermediate scales. In two dimensions, this transform outperforms the standard discrete wavelet transformation in terms of shift-invariant. Although the transformation utilizes more wavelets, sampling rates are high costs and some lack a dominant spatial orientation, which prevents them from being able to isolate those directions. A solution to this problem is a non separable method. The quincunx lattice is a non-separable sampling method in image processing. It treats the different directions more homogeneously than the separable two dimensional schemes. Proposed wavelet transformation can generate sub-images of multiple degrees rotated versions. Therefore, This method services good performance in image processing fields.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.51 no.6
• /
• pp.221-227
• /
• 2014

In this paper, we propose a synthesis method that can effectively suppress the ambience which affects tonal components in the PS decoder. Ambience component was obtained by using decorrelation filter and the weighting of the ambience in the decoder was determined through IC parameter. However, since the parameters are extracted in the sub-band domain, a low IC value could be analyzed even if the tonal component is dominant. The quality of the output signal may be degraded. To prevent this problem, the tonality was measured in the downmixed signal and the weighting of the ambience components were adjusted appropriately according to the measured tonality index. The performance of the proposed method was evaluated by simulations. Furthermore, the subjective test was performed and the results confirmed that the proposed method offers improved quality.

• Korean Journal of Materials Research
• /
• v.32 no.8
• /
• pp.345-353
• /
• 2022

In this study, using deep learning, super-resolution images of transmission electron microscope (TEM) images were generated for nanomaterial analysis. 1169 paired images with 256 × 256 pixels (high resolution: HR) from TEM measurements and 32 × 32 pixels (low resolution: LR) produced using the python module openCV were trained with deep learning models. The TEM images were related to DyVO₄ nanomaterials synthesized by hydrothermal methods. Mean-absolute-error (MAE), peak-signal-to-noise-ratio (PSNR), and structural similarity (SSIM) were used as metrics to evaluate the performance of the models. First, a super-resolution image (SR) was obtained using the traditional interpolation method used in computer vision. In the SR image at low magnification, the shape of the nanomaterial improved. However, the SR images at medium and high magnification failed to show the characteristics of the lattice of the nanomaterials. Second, to obtain a SR image, the deep learning model includes a residual network which reduces the loss of spatial information in the convolutional process of obtaining a feature map. In the process of optimizing the deep learning model, it was confirmed that the performance of the model improved as the number of data increased. In addition, by optimizing the deep learning model using the loss function, including MAE and SSIM at the same time, improved results of the nanomaterial lattice in SR images were achieved at medium and high magnifications. The final proposed deep learning model used four residual blocks to obtain the characteristic map of the low-resolution image, and the super-resolution image was completed using Upsampling2D and the residual block three times.