• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.20 no.1
• /
• pp.117-122
• /
• 2016

In this paper, we propose 24-GHz CMOS radio frequency (RF) power amplifier for short-range automotive collision avoidance radars. This circuit contains common source stage with inter-stages conjugate matching circuit as a class-A mode amplifier. The proposed circuit is designed using TSMC $0.13-{\mu}m$ mixed signal/RF CMOS process ($f_T/f_{MAX}=120/140GHz$). It operates at the supply voltage of 2V, and it is designed to have high power gain, low insertion loss and low noise figure in the low supply voltage. To reduce total chip area, the circuit used transmission lines instead of the bulky real inductor. The designed CMOS power amplifier showed the smallest chip size of $0.1mm^2$, the lowest power consumption of 40mW, the highest power gain of 26.5dB, the highest saturated output power of 19.2dBm and the highest maximum power-added efficiency of 17.2% as compared to recently reported results.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.12 no.8
• /
• pp.3697-3705
• /
• 2011

There is the temporal correlation of the video sequence between the motion vector of current block and the motion vector of previous block. In this paper, we propose a new prediction search algorithm for block matching using the temporal and spatial correlation of the video sequence and local statistics of neighboring motion vectors. The proposed ANBA(Adaptive Neighboring-Block Search Algorithm) determines the location of a better starting point for the search of an exact motion vector using the point of the smallest SAD(Sum of Absolute Difference) value by the predicted motion vectors of neighboring blocks around the same block of the previous frame and the current frame and use a previous motion vector. Simulation results show that PSNR(Peak-to-Signal Noise Ratio) values are improved up to the 1.06dB as depend on the video sequences and improved about 0.01~0.64dB over MVFAST and PMVFAST.

• Proceedings of the Korean Institute of Information and Commucation Sciences Conference
• /
• 2000.10a
• /
• pp.190-195
• /
• 2000

This paper presents the fabrication of the LNA which is operating at 2.13∼2.16 GHz for IMT-2000 lot-end receiver using series feedback and resistive decoupling circuit. Series feedback added to the source lead of a transistor keep the low noise characteristics and drop the input reflection coefficient of amplifier simultaneously. Also, it increases the stability of the LNA. Resistive decoupling circuit is suitable for input stage matching because a signal at low frequency is dissipated by a resistor in the matching network The amplifier consist of GaAs FET ATF-10136 for low noise stage and VNA-25 which is internally matched MMIC for high gain stage. The amplifier is fabricated with both the RF circuits and self bias circuit on the Teflon substrate with 3.5 permittivity. The measured results of the LNA which is fabricated using above design technique are presented more than 30 dB in gain P$\_$ldB/ 17 dB and less than 0.7 dB in noise figure, 1.5 in input$.$output SWR(Standing Wave Ratio).

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.31 no.7B
• /
• pp.595-601
• /
• 2006

This study presents an ultrasonic location awareness system for the ubiquitous computing with absolute position. The flight time of ultrasonic waves is determined by a period detecting technique which is able to extend the sensing range compared with traditional methods. For location awareness, ultrasonic waves are sent successively from each ultrasonic transmitter and synchronized by radio frequency (RF) signal, where the transmitting part is fixed and the receiving part is movable. To expand the recognizing range, cell matching technique and coded ultrasonic technique are introduced. The experimentation for various distances is accomplished to verify the used period detecting technique of U-SAT system. The positioning accuracy by using cell matching is also verified by finding the locations of settled points and the usability of coded ultrasonic technique is verified. As a result, the possibility of ultrasonic location awareness system for the ubiquitous computing can be discussed as a pseudo-satellite system with low cost, a high update rate, and relatively high precision, in the places where GPS is not available.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.24 no.6A
• /
• pp.920-930
• /
• 1999

Many researches on the multi-level QAM(Quadrature Amplitude Modulation) which is known to be a promising digital data transmission method for efficient use of channel bandwidth have been carried on, and their applications to various real fields are now being in progress. However, in the band-limited communication systems, each transmitted symbols is distorted by the ISI(Intersymbol Interference) and the phase error. Therefore, an equalizer and a carrier recovery must be taken into considerations to attenuate the effects of these distortions in the receiver. This paper presents an effective receiver structures that is applicable to the multi-level QAM. The proposed receiver system is consisted of an equalizer with Godard’s blind algorithm and a carrier recovery circuit. The phase error is estimated with a $\theta$-matching algorithm and is used in the carrier recovery to recover the correct phase. The simulation results are included to evaluate performance of the proposed receiver system for the various channel models.

• The Journal of Information Technology
• /
• v.3 no.2
• /
• pp.39-47
• /
• 2000

Among the compression methods of moving picture information, a motion estimation method is used to remove time-repeating. The Block Matching Algorithm in motion estimation methods is the commonest one. In recent days, it is required the more advanced high quality in many image processing fields, for example HDTV, etc. Therefore, we have to accomplish not by means of Partial Search Algorithm, but by means of Full Search Algorithm in Block Matching Algorithm. In this paper, it is suggested a structure that reduce total calculation quantity and size, because the structure using Bit Plane select and use only 3bit of 8bit luminance signal.

• Journal of IKEEE
• /
• v.2 no.1 s.2
• /
• pp.15-23
• /
• 1998

In this paper, distributed mixer is studied at microwave frequency. The circuit of distributed mixer composed of gate 1,2, drain transmission lines, matching circuits in input and output terminal, DGFET's. For impedance matching of input and output port at higher frequency, image impedance concept is introduced. In distributed mixer, a DGFET's impedances are absorbed by artificial transmission line, this type of mixer can get a very broadband characteristics compared to that of current systems. A RF/LO signal is applied to each gate input port, and are excited the drain transmission line through transcondutance of the DGFET's. The output signals from each drain port of DGFET's added in same phases. We designed and frabricated the distributed mixer, and a conversion gain, noise figure, bandwidth, LO/RF isolation of the mixer are shown through computer simulation and experimentation.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.41 no.5
• /
• pp.87-97
• /
• 2004

In this paper, we propose an algorithm for interlaced-to-progressive conversion by the weighted summation of the information collected from spatial do-interlacing method, in which the weighted edge based line average is applied, and the temporal method in which the motion compensation is employed by using hi-directional BMA (block matching algorithm). We employed time-recursive and motion adaptive processing as motion detection is involved. Also, a median filter is used to deal with limitation of the linear summation in which only an intermediate of values being involved is determined. The main goal of the approach is to overcome the shortcomings of each of the do-interlacing techniques without significant increment of the computational complexity, and the proposed method is apt to implement in hardware for real-time processing.

• The Journal of the Korea Contents Association
• /
• v.11 no.9
• /
• pp.515-523
• /
• 2011

It is important to manage large amount of information from various information providers for supporting recent information services such as providing global research trends, detecting emerging signal and listing leading researchers. For integrated management, definition of integrated metadata schema, data transformation and schema matching are needed. It is first necessary to analyze existing various metadata for defining integrated metadata schema. In this paper, we have analyzed several metadata of scientific journal papers by classifying semantics, content rules and syntax, and looked around considerations to make integrated schema or transform metadata. We have known that XML is used as a syntax for supporting convenience and various usage condition, and hierarchy element names and common elements in semantics are needed. We also have looked at elements having various content rules and related standards. We hope that this study will be used as basic research material of metadata integrated management, data transform and schema matching for interoperability.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.48 no.9
• /
• pp.47-53
• /
• 2011

The signal transmission properties of the connector such as insertion loss and return loss are investigated using analysis procedure of S-parameter simulation, equivalent model extraction, and characteristic impedance calculation. S-parameter simulation is performed by connector's modeling and solving based on 3-dimensional finite element method. The connector's equivalent model of ${\pi}$ type is are proposed and extracted with an optimization process of circuit analysis simulator. The characteristic impedance of the connector is calculated with results of circuit analysis simulation and S-parameter data. According to the connector's characteristic impedance, it's revised design is carried out. In this work, the connector's effective contact area is increased and its body is applied as a high dielectric material in order to increase its capacitance and then obtain impedance matching. Therefore, return loss of the connector is improved by approximately 10 dB due to its design revision.