• Journal of the Korean Society for Nondestructive Testing
• /
• v.36 no.6
• /
• pp.490-495
• /
• 2016

Pulsed eddy current (PEC) testing signals have typically been obtained from the electromotive force induced in a sensor coil. However, an increasing number of studies have elected to incorporate the Hall plate as a sensor. Thus, accurate numerical modeling of the Hall sensor signal is necessary. In this study, a PEC probe is designed and a numerical modeling program is written so that Hall sensor signals and coil sensor signals can be calculated simultaneously. First, a step current is used as the input current. The predicted Hall sensor signals show similar characteristics to those of the experimental signals reported by other researchers. The characteristics of the two types of signals are then analyzed and compared as the thickness of test object changes. The results show that the Hall sensor signal provides less information for evaluating the thickness of the test object than the coil sensor signal. The response signals from a pulsed input current are also calculated, and it is confirmed that an equivalent reversed signal pattern appeared after the pulse width at both signals.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.8 no.4
• /
• pp.89-95
• /
• 2008

In the maritime communication, Orthogonal Frequency Division Multiplexing (OFDM) communication terminal should be operated with low power consumption, because the communication should be accomplished in the circumstance of disaster. Therefore, Low power FFT processor is required to be designed with current mode signal processing technique than digital signal processing. Current- to-Voltage Converter (IVC) is a device that converts the output current signal of FFT processor into the voltage signal. In order to lessen the power consumption of OFDM terminal, IVC should be designed with low power design technique and IVC should have wide linear region for avoiding distortion of signal voltage. To design of one-chip of the FFT LSI and IVC, IVC should have a small chip size. In this paper, we proposed the new IVC with wide linear region. We confirmed that the proposed IVC operates linearly within 0.85V to 1.4V as a function of current-mode FFT output range of -100~100[uA]. Designed IVC will contribute to realization of low-power maritime data communication using OFDM system.

• The Transactions of the Korean Institute of Power Electronics
• /
• v.10 no.3
• /
• pp.219-225
• /
• 2005

In this paper, a new discrete-time small signal model of an average current mode control is proposed to predict the inductor current responses. Compared to the peak current mode control, the analysis of the average current mode control is difficult because of its presence of an compensation network. By utilizing sampler model, a new discrete-time small signal model is derived and used to predict the behaviors of an inductor current of average current mode control employing generalized compensation networks. In order to show the usefulness of the proposed model, prediction results of the proposed model are compared to those of the circuit level simulator, PSIM and experiment.

• Journal of Electrical Engineering and Technology
• /
• v.1 no.3
• /
• pp.279-286
• /
• 2006

A method for estimating the instantaneous phasor of a fault current signal is proposed for high-speed distance protection that is immune to a DC-offset. The method uses a modified notch filter in order to eliminate the power frequency component from the fault current signal. Since the output of the modified notch filter is the delayed DC-offset, delay compensation results in the same waveform as the original DC-offset. Subtracting the obtained DC-offset from the fault current signal yields a sinusoidal waveform, which becomes the real part of the instantaneous phasor. The imaginary part of the instantaneous phasor is based on the first difference of the fault current signal. Since a DC-offset also appears in the first difference, the DC-offset is removed trom the first difference using the results of the delay compensation. The performance of the proposed method was evaluated for a-phase to ground faults on a 345kV 100km overhead transmission line. The Electromagnetic Transient Program was utilized to generate fault current signals for different fault locations and fault inception angles. The performance evaluation showed that the proposed method can estimate the instantaneous phasor of a fault current signal with high speed and high accuracy.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.20 no.9
• /
• pp.103-109
• /
• 2006

This research is contents about output characteristic of optic current sensor that use faraday effect. optic current sensor used in an experiment is consisted of three parts.(1) Source of light used laser diode of 1310[nm].(2) Sensor section manufactured circularly according to gas insulated switchgear. And $9/125[{\mu}m]$ standard single mode optical fiber for communication was installed winding 20 [turn] on sensor section core surroundings of diameter 31 [cm].(3) Electrical signal of PD(Photo detector) is collected using NI company's 16bit DAQ board via terminal block. Collected data analyzed by different three signal processing methods. NI company's $Labview^{TM}$ was used to signal processing software. As a result, In signal processing of optic current sensor, we could know that noise greatly more influences the error generation than fluctuation of light intensity. also, 1 class CT(current transformer) manufacture that have error rate less than 1[%] was available by removing these

• Journal of the Korean Institute of Telematics and Electronics C
• /
• v.36C no.11
• /
• pp.10-17
• /
• 1999

In this paper, CMOS IADC(Current-mode Analog-to-Digital Converter) which consists of only CMOS transistors is proposed. Each stages is made up 1.5-bit bit cells composed of CSH(Current-mode Sample-and-Hold) and CCMP(Current Comparator). The differential CSH which designed to eliminate CFT(Clock Feedthrough), to meet at least 9-bit resolution, is placed at the front-end of each bit cells, and each stages of bit cell ADSC (Analog-to-Digital Subconverter) is made up two latch CCMPs. With the HYUNDAI TEX>$0.65\mu\textrm{m}$ CMOS parameter, the ACAD simulation results show that the proposed IADC can be operated with 47 dB of SINAD(Signal to Noise- Plus-Distortion), 50dB(8-bit) of SNR(Signal-to-Noise) and 37.7 mW of power consumption for input signal of 100 KHz at 20 Ms/s.

• Proceedings of the KSME Conference
• /
• 2008.11a
• /
• pp.938-942
• /
• 2008

To detect the failures in machine, the signals of current, vibration and acoustic emission are widely used in industry. And unexpected failures of gears are not only extremely damaging but also lead to economic losses. In this paper, to detect the misalignment occurred at between two gears in gearboxes, the signals of current, vibration and AE were measured at gearbox and motor power line. FFT(Fast Fourier Transform) was used for current and vibration signal analysis to find gear failure frequency. Especially, the envelop analysis and wavelet transform were applied for AE signal. Therefore, compared with the results of three kinds of signal, the possibility of earily detection by AE is identified or checked.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.50 no.9
• /
• pp.445-452
• /
• 2001

Two switching signal patterns are proposed to prevent short circuit of PWM ac choppers. The voltage detection method and the current detection method are proposed to execute two switching signal patterns. In the voltage detection method, the dead-time has to be inserted to the switching signals after polarity of input voltage is checked by voltage transducer at input side. In the current detection method, the direction of load current is checked by current transducer at output side, and the dead-time delay is not considered. Controlling circuit built by current detection method is simple because the dead-time delay is considered. The experimental results are presented to prevent short circuit of ac chopper safely.

• The Transactions of the Korean Institute of Electrical Engineers P
• /
• v.51 no.4
• /
• pp.219-221
• /
• 2002

This paper presents an electric scooter development using blushless DC motor. In recent scooters was to develop for sport leisure and short transportation. Most of scooter are used petroleum gas. This gas scooter has disadvantage to pollute the air. Some of scooters have developed by DC motor which require a brush. However brushless motors have higher maximum speed and greater capacity, save maintenance labour and produce less noise. There is also greater freedom in planing the usage of brushless motors. In this paper we develop an electric scooter driving BLDC motor for design smart system and control speed of scooter with current reference signal to apply voltage to motor by means of three phase inverter. Using accelerator device we generate current reference to control speed and send the current to a MICOM by A/D converter. This MICOM produces the voltage signal and hall sensors signal and PWM controller drive three phase inverter to minimize error between the reference and an actual current.

• Journal of Power System Engineering
• /
• v.14 no.4
• /
• pp.63-67
• /
• 2010

This paper introduces the eddy current signal characteristic of magnetic and non-magnetic gas turbine rotor. In the past, Magnetic particle inspection method was used in magnetic material for qualitative defect evaluation and the ultrasonic test method was used for quantitative evaluation. Nowadays, eddy current method is used in magnetic gas turbine rotor inspection due to advanced sensor design technology. We are studying on the magnetic gas turbine rotor by using eddy current method. We prepared diverse depth specimens made by magnetic and non-magnetic materials. We select optimum frequency according to material standard penetration data and experiment results. We got the signal on magnetic and non-magnetic material about 0.2 mm, 05 mm, 1.0 mm, 1.5 mm 2.0 mm and 2.5 mm depth defects and compare the signal amplitude and signal trend according to defect depth and frequency. The results show that signal amplitudes of magnetic are bigger than non-magnetic material and the trends are similar on every defect depth and frequency. The detection and resolution capabilities of eddy current are more effective in magnetic material than in non-magnetic materials. So, the eddy current method is effective inspection method on magnetic gas turbine rotor. And it has the merits of time saving and simple procedure by elimination of the ultrasonic inspection in traditional inspection method.