• Journal of Satellite, Information and Communications
• /
• v.9 no.2
• /
• pp.28-32
• /
• 2014

In this paper, we analyzed the performance of cyclostationary signal detection scheme for LTE system. We applied the cyclostationary signal detection scheme to the cognitive radio(CR) technology, which improves the usage efficiency of spectrums and shares frequencies, and we detected the signal in the long term evolution(LTE) band. LTE system has been designated as the standard to improve the maximum data rate and provide the low latency in the 3rd generation partnership project(3GPP). In this paper, we generated the LTE signals based on the orthogonal frequency division multiple access(OFDMA) and analyzed the performance of signal detection in accordance with the segment and threshold of the generated signals. Gaussian channel was used in the simulation and we discussed the future studies to apply the CR to the LTE system.

• Journal of the Korean Society of Radiology
• /
• v.17 no.6
• /
• pp.897-902
• /
• 2023

The purpose of this paper is to analyze the characteristics of Silicon Photomultiplier (SiPM) for the realization of high-sensitivity radiation detection in portable detectors. Portable X-ray detectors offer the advantage of quickly accessing the patient's location and obtaining real-time images, allowing physicians to perform rapid diagnoses. However, this mobility comes with challenges in achieving accurate radiation detection. In existing detectors, SiPM is used for a simple purpose of detecting X-ray triggers. To verify the feasibility of high-sensitivity X-ray detection through SiPM, seven types of SiPM sensors were compared and selected, and their characteristics were analyzed. The SiPM used in the final test demonstrated the ability to distinguish signals at the ultra-low radiation level of 10 nGy, and it was observed that the slope of the signal rise curve varies with the X-ray tube voltage. Utilizing the characteristics of SiPM, which exhibits changes in signal level and duration with X-ray dose, it appears possible to achieve high-sensitivity measurements for X-ray detection.

• International Journal of Aeronautical and Space Sciences
• /
• v.6 no.1
• /
• pp.8-16
• /
• 2005

This paper describes target detection performance of millimeter wave radar that exits on non-stationary target detection schemes in the ground clutter conditions. The comparison of various CFAR process schemes such as CA(Cell-Average)-CFAR, GO(Greatest Of)/SO(Smallest Of)-CFAR, and OS(Order Statistics)-CFAR performance are applied. Using matlab software, we show the performance and loss between target detection probability and signal to noise ratio. This paper concludes the OS-CFAR process performance is better than any others and satisfies the optimal detection probability without loss of detection in the homogeneous clutter, When range bins increase.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.44 no.2
• /
• pp.55-61
• /
• 2007

In this paper, we represent the maximum detection probability formulas of symbol synchronization timing at each received delay signal in multipath channel delay profile in the multiplied correlation and difference type correlated symbol synchronization timing detection method. The computer simulation results show that the correlation symbol timing detection method have maximum detection probability at the lead of received delay signal of highest amplitude, but the difference type of correlation symbol timing detection method always have maximum detection probability at the lead of first received delay signal in the multipath channel models. Using this results, we show the BER characteristics difference between the IEEE802.11a OFDM signals which is obtained in case of the symbol synchronization timing is taken at zero error(perfect) timing position and at -1 sample error symbol timing position from perfect timing position in the multipath channel models regardless the length of channel delay spread.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.17 no.3
• /
• pp.450-456
• /
• 2016

STDR (sequence time domain reflectometry) to detect a cable fault using a pseudo noise sequence as a reference signal, and time correlation analysis between the reference signal and reflection signal is robust to noisy environments and can detect intermittent faults including open faults and short circuits. On the other hand, if the distance of the fault location is far away or the fault type is a soft fault, attenuation of the reflected signal becomes larger; hence the correlation coefficient in the STDR becomes smaller, which makes fault detection difficult and the measurement error larger. In addition, automation of the fault location by detection of phase and peak value becomes difficult. Therefore, to improve the cable fault detection of a conventional STDR, this paper proposes the algorithm in that the peak value of the correlation coefficient of the reference signal is detected, and a peak value of the correlation coefficient of the reflected signal is then detected after removing the reference signal. The performance of the proposed method was validated experimentally in low-voltage power cables. The performance evaluation showed that the proposed method can identify whether a fault occurred more accurately and can track the fault locations better than conventional STDR despite the signal attenuation. In addition, there was no error of an automatic fault type and its location by the detection of the phase and peak value through the elimination of the reference signal and normalization of the correlation coefficient.

• Journal of the Korean Society for Precision Engineering
• /
• v.16 no.1 s.94
• /
• pp.61-67
• /
• 1999

A laser Doppler vibrometer based on the laser heterodyne interferometry is employed to measure the vibration velocity of vibrating objects. In this paper, we propose a real time analog signal processor of a laser Doppler vibrometer to reduce the degradation of Doppler signals mainly caused by environmental noises. In the proposed real time signal processor of an laser Doppler vibrometer, a pre-processor and a logical motion direction detector are designed to reduce the detection errors of the object motion direction. Also, a noise detection and rejection circuit is designed to reject the unfiltered noises.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.29 no.3
• /
• pp.102-106
• /
• 2015

In order to avoid the electrical fire, AFCI(Arc Fault Cirruit Interrupter) has been obligated to be adopted in the United States of America since 2002. A study was carried out on how to detect Arc. In this paper, The propose is high-frequency signal detection methods and RSSI(Received Signal Strength Indication) signal processing algorithm for Arc detection. and the electrical characteristics were verifying.

• Journal of Biosystems Engineering
• /
• v.24 no.3
• /
• pp.253-258
• /
• 1999

This study was conducted to develop an automatic egg inspection system for detecting creaked eggs based on acoustic impulse response. This system includes a sound generator, a sound sensor with signal conditioner, and a computer. The sound generator that hit the sharp of the dull edges of an egg was constructed with a ceramic ball pendulum attached to a rotary type solenoid. The signal conditioner included a pre-amplifier and a digital signal processing (DSP) board. The parameters for distinguishing cracked and normal eggs were the area, the geometric centroid and the resonance frequency of power spectrum of the acoustic signal generated. An algorithm for on-line detection of the continuous transferring eggs was developed. The performance tests resulted with 91% success rate to separate cracked and normal eggs at the rate of 1 second per an egg.

• Journal of information and communication convergence engineering
• /
• v.10 no.2
• /
• pp.175-180
• /
• 2012

This paper presents a blind watermark detection scheme for an additive watermark embedding model. The proposed estimation-correlation-based watermark detector first estimates the embedded watermark by exploiting non-Gaussian of the real-world audio signal and the mutual independence between the host-signal and the embedded watermark and then a correlation-based detector is used to determine the presence or the absence of the watermark. For watermark estimation, blind source separation (BSS) based on independent component analysis (ICA) is used. Low watermark-to-signal ratio (WSR) is one of the limitations of blind detection with the additive embedding model. The proposed detector uses two-stage processing to improve the WSR at the blind detector; the first stage removes the audio spectrum from the watermarked audio signal using linear predictive (LP) filtering and the second stage uses the resulting residue from the LP filtering stage to estimate the embedded watermark using BSS based on ICA. Simulation results show that the proposed detector performs significantly better than existing estimation-correlationbased detection schemes.

• Proceedings of the KSR Conference
• /
• 2000.11a
• /
• pp.733-739
• /
• 2000

This paper is described the development of on-line partial discharge detector for high voltage apparatus. This detector consists of acoustic and high frequency current sensors, amplifier part, A/D converter part, data communication part and computer. The contents of paper are characteristics of units and digital signal processing for reducing noise in partial discharge detection. We seek methods to do good digital signal processing for detection of partial discharge. We apply digital filtering methods to the elect Tic signal and a cross con-elation to the acoustic signal. This paper shows the characteristics of these filtering method and cross con-elation in partial discharge detection.