• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2009년도 세계 도시지반공학 심포지엄
• /
• pp.923-932
• /
• 2009

Generally most of pile foundations are constructed with group pile rather than single pile. The study on efficiency and bearing capacity which are major elements for rational design of this group pile has been actively progressed, whereas there are truly only a few studies of negative skin friction working on group pile due to the consolidation of ground. The purpose of this study is to determine, among the elements of negative skin friction applied to pile, the occurrence modality of negative skin friction at center, side, and corner of $3{\times}3$ group pile using model test and, based on those observations, to propose the effective design direction of group pile.

• 한국군사과학기술학회지
• /
• 제3권2호
• /
• pp.213-218
• /
• 2000

An experimental study was performed to investigate the effect of surface temperature mismatch on measurements of skin friction using a plug-type skin friction gage mounted on the side wall of a supersonic wind tunnel. The freestream Mach number was 2.4 and Reynolds number per meter was $5.25 {\times}10^7$ with total pressure of 50 psi and total temperature of 275K. Temperature mismatch between the gage surface and surrounding wall surface was generated by hot water injection using the active temperature control system. Results of the tests showed that the temperature mismatch made sizable effects on the measurements of skin friction.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 2010년도 춘계 학술발표회
• /
• pp.1077-1087
• /
• 2010

Generally most of pile foundations are constructed with group pile rather than single pile. The study on efficiency and bearing capacity which are major elements for rational design of this group pile has been actively progressed, whereas there are truly only a few studies of negative skin friction working on group pile due to the consolidation of ground. The purpose of this study is to determine, among the elements of negative skin friction applied to pile, the occurrence modality of negative skin friction at center, side, and corner of $3{\times}3$ group pile using model test and, based on those observations, to propose the effective design direction of group pile.

• 한국지반공학회:학술대회논문집
• /
• 한국지반공학회 1999년도 봄 학술발표회 논문집
• /
• pp.249-258
• /
• 1999

Dynamic load and static load tests are performed on steel pipe piles and concrete piles at five construction sites in highway to compare the difference of load bearing mechanisms. At each site, one steel pile is instrumented with electric strain gages and dynamic tests are performed on the pile during installation. Damages of strain gages due to the installation are checked and static test is performed upon the same pile after two or seven days as well. It shows that load transfer from side friction to base resistance behaves somewhat differently according to the results of load-settlement analysis obtained from PDA and static load test. Initial elastic stage of load settlement curves of two load tests is almost similar. But after the yielding point, dynamic resistance of pile behaves more stiffer than static resistance, thus, dynamic load test result might overestimate the real pile capacity compared with static result. Analysis of gage readings shows that unit skin friction increases exponentially with depth. The skin friction is mobilized at the 1∼2m above the pile tip and contributes to the considerable side resistance. Comparison of side and base resistances between the measured value and the calculated value by Meyerhof's bearing capacity equation using SPT N value shows that the calculated base resistance is higher than the measured. Therefore, contribution of side resistance to total capacity shouldn't be ignored or underestimated. Finally, based upon the overall test results, a construction control procedure is suggested.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2008년도 춘계학술대회논문집
• /
• pp.101-104
• /
• 2008

The sailfish is the fastest sea animal, reaching its maximum speed of 110km/h. On its skin, a number of V-shaped protrusions pointing downstream exist. Thus, in the present study, the possibility of reducing the skin friction using its shape is investigated in a turbulent boundary layer. We perform a parametric study by varying the height and width of the protrusion, the spanwise and streamwise spacings between adjacent ones, and their overall distribution pattern, respectively. Each protrusion induces a pair of streamwsie vortices, producing low and high shear stresses at its center and side locations, respectively. These vortices also interact with those induced from adjacent protrusions. As a result, the drag is either increased or unchanged for all the cases considered. In some cases, the skin friction itself is reduced but total drag including the form drag on the protrusions is larger than that of a smooth surface. Since the shape of present protrusions is similar to that used by Sirovich and Karlsson [Nature 388, 753 (1997)] where V-shaped protrusions pointing upstream were considered, we perform another set of experiments following their study. However, we do not obtain any drag reduction even with random distribution of those V-shaped protrusion.

• 한국지반공학회논문집
• /
• 제28권6호
• /
• pp.19-29
• /
• 2012

일반마이크로파일의 저항성능을 개선시키기 위해 최근에 토목섬유을 활용한 팩마이크로파일이 개발되었다. 팩마이크로파일은 일반마이크로파일의 강봉이나 강관을 토목섬유팩으로 감싸고 주입재와 주입압을 토목섬유팩 내부에 가하여 제작한다. 이 주입압에 의하여 천공 직경이 크게 확대된다. 동일한 한 지반 속에 설치된 세 개의 마이크로파일을 대상으로 일련의 말뚝인발시험을 실시하였다. 세 말뚝 중 두 개는 팩마이크로파일였고 나머지 하나는 강봉을 사용한 일반마이크로파일이였다. 토목섬유팩에 적용된 주입압에 의하여 팩마이크로파일의 경우 천공직경이 152mm에서 220mm으로 확대되었다. 마이크로파일의 주면에서 발달하는 단위주면마찰력은 말뚝두부의 인발변위량의 증가와 함께 서서히 증가하여 한계상태에 도달한 한계변위량에서 수렴치에 도달한다. 팩마이크로파일의 인발저항력은 일반마이크로파일의 인발저항력보다 크게 나타난다. 이와 같은 팩마이크로파일의 인발저항력을 증대시킬 수 있는 원인으로는 크게 두 가지를 생각할 수 있다; 첫째는 마이크로파일에 설치한 토목섬유팩내 주입압으로 마이크로파일의 단면적을 증대시키므로 말뚝주면의 마찰저항면적을 증대시킬 수 있기 때문이고, 둘째는 마이크로파일의 단면이 확대될 때 확대되는 부분의 체적만큼의 토사가 주변지반을 압축시켜 말뚝과 지반 사이의 마찰저항력을 증대시킬 수 있기 때문이다. 이 압축효과는 지표면 부근 보다 깊은 지층에서 크게 나타났다. 말뚝 주면에서 발휘되는 단위주면마찰력은 말뚝의 직경이 작은 경우가 더 크게 발휘된다. 즉 마이크로파일의 주면에서 발달되는 단위주면마찰력은 대구경 현장타설말뚝의 주면에서 발달되는 단위주면마찰력보다 크게 나타난다.

• 한국지반공학회논문집
• /
• 제23권1호
• /
• pp.5-11
• /
• 2007

최근 사용이 증가 추세에 있음에도 불구하고 마이크로파일의 하중전이곡선에 관한 연구는 매우 미미한 실정이다. 이에 본 연구에서는 국내지반 및 시공조건이 반영된 실물크기의 시험말뚝에 대한 현장시험을 실시하여 마이크로파일의 주면하중전이곡선을 산정하는 경험식을 제안하였다. 말뚝재하시험 결과로부터 깊이별 하중전이곡선을 구하고, 이를 쌍곡선 함수형태로 전환 시킨 후, 하중전이함수와 지반의 표준관입시험 저항치(N)와의 관계를 정립하였다. 이러한 일련의 과정을 거친 결과를 토대로 유한차분법과 문헌자료를 활용하여 개발된 하중전이함수로부터 풍화토에서 마이크로파일의 주면마찰력을 추정할 수 있음을 평가하였다.

• 한국항해항만학회지
• /
• 제33권3호
• /
• pp.227-233
• /
• 2009

본 실험 연구는 공기분사공법의 오픈케이슨기초의 주면마찰력 저감효과에 대해 규명하기 위해 이루어졌다. 연육교 건설을 위해 기초로 사용된 공기구멍이 설치된 대구경 케이슨이 본 연구를 위해 이용되었다. 공기분사공법을 사용 시, 침하 시간을 줄일 수 있었으며 일반전인 방법으로 도달할 수 없는 깊이까지 침하를 시킬 수 있었다. 또한, 예상했던 것 보다 두 배 이상의 주면마찰저항력 저항 저감 효과를 얻었으며, 이런 장점 외 추가적인 외부의 재하하중 없이도 케이슨을 침하시킬 수 있음을 보여주었다. 그 외 오픈케이슨 침설 시 발파에 의한 케이슨 손상을 공기분사공법을 이용하면 방지할 수 있음을 보여주었다.

• 대한기계학회논문집B
• /
• 제26권12호
• /
• pp.1681-1691
• /
• 2002

The heat transfer and pressure drop characteristics of heat exchangers with louver fins were experimentally investigated. The samples had small fin pitches (1.0 mm to 1.4 mm), and experiments were conducted up to a very low frontal air velocity (as low as 0.3 m/s). At a certain Reynolds number (critical Reynolds number), the flattening of the heat transfer coefficient curve was observed. The critical Reynolds number was insensitive to the louver angle, and decreased as the louver pitch to fin pitch ratio (L$_{p}$F$_{p}$) decreased. Existing correlations on the critical Reynolds number did not adequately predict the data. It is suggested that, for proper assessment of the heat transfer behavior, the louver pattern in addition to the flow characterization need to be considered. The heat transfer coefficient increased as the fin pitch decreased. At low Reynolds numbers, however, the trend was reversed. Possible explanation is provided considering the louver pattern between neighboring fins. Different from the heat transfer coefficient, the friction factor did not show the flattening characteristic. The reason may be attributed to the form drag by louvers, which offsets the decreased skin friction at a low Reynolds number. The friction factor increased as the fin pitch decreased and the louver angle increased. A new correlation predicted 92% of the heat transfer coefficient and 90% of the friction factor within $\pm$10%.10%.

• Journal of Biosystems Engineering
• /
• 제41권3호
• /
• pp.201-207
• /
• 2016

Purpose: A water-spraying type automatic glochids removal system for cactus (Opuntia humifusa) stem was developed, and its performance was evaluated. The system was developed to reduce intensive human labor in removing glochids from cactus stem skin without inducing damage prior to further processing into value-added products. Methods: The developed system consists of conveyor and water-spraying systems. The conveyor system delivers cactus stems through water-spraying compartments and finally to a collecting box. In order to remove the glochids, rotating nozzles spray water over all areas (i.e., front and back faces and sides) of the cactus skin under controlled water pressure. Operating conditions such as conveyor speed, water pressure, angle of water-spraying nozzles, distance between conveyor belt and rotating nozzles, and angle of cactus flipping slide were adopted from our previous study and applied on the system design and manufacturing. The performance of glochids removal was evaluated by counting the number of glochids on the cactus stem before and after processing on the system. Results: The developed system performed efficiently and effectively under the pre-studied operating conditions except for the angle of cactus flipping slide. The new system had a glochids removal ratio of 94.1% without damaging the cactus skin. Considering the original number (approximately 30-60) of glochids, the remaining number was low (1-4), and most of them were found at the side edge of the cactus stem. This system can remove glochids from 360 cactus stems in 1 hr regardless of cactus size. Conclusions: The performance of the new system in glochids removal without damaging cactus skin is superior to any other existing device (i.e., brush type, rubber-friction type, and agitation type). The system is expected to be applied in cactus (O. humifusa) processing facilities.