• 한국수자원학회논문집
• /
• 제46권9호
• /
• pp.947-956
• /
• 2013

급경사 산지하천 수충부의 호안은 대부분 콘크리트 옹벽으로 되어있다. 표면이 매끄러운 콘크리트 옹벽호안은 유속을 더 강화시키기 때문에 수충부 홍수피해의 원인이 되기도 한다. 본 연구에서는 개수로의 한 측벽에 설치한 정사각형 단면의 세로돌출줄눈이 흐름저항에 미치는 영향을 파악하기 위해 수리실험을 수행하였다. 돌출줄눈의 설치간격은 무차원 돌출줄눈 간격 ${\lambda}_{nv}$를 기준으로 조도유형 d형과 k형을 포함하도록 설계하였다. 흐름의 Froude 수는0.81~1.12의 범위였다. 흐름저항은 돌출줄눈의 설치간격과 유량에 좌우되었다. ${\lambda}_{nv}$가 9일 때 흐름저항이 가장 큰 것으로 나타났다. 세로돌출줄눈은 유량이 증가하면 d형 조도에서는 흐름저항을 감소시켰으나 k형 조도에서는 흐름저항을 증가시켰다. 흐름저항의 증가폭은 ${\lambda}_{nv}$이 9~12의 범위에서 상대적으로 더 크게 나타났다. 세로돌출줄눈에 의한 흐름저항은 대부분 형상저항에 의한 것이며 그 등가조도높이는 수심규모로 발생할 수 있고 흐름저항에 미치는 영향이 매우 크다. 측벽의 세로돌출줄눈은 흐름저항을 증가시키고 최대유속의 발생위치를 수로의 횡단면 중앙방향으로 이동시키는 수단으로 사용될 수 있을 것이다.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2002년도 춘계학술대회 논문집
• /
• pp.614-618
• /
• 2002

In hot strip mills, Portable Roll Scanner (the portable roll surface temperature and profile measuring device) can be used to calibrate on-line Process models for strip crown and flatness by measuring the thermal expansion and wear profile of the rolls. And the surface temperature measurement can be used to optimize the roll cooling system. Portable Roll Scanner consists of the measuring device, which has two contact inductive distance transducers for roll profile measurement and one infrared Pyrometer for surface temperature measurement, and computer-based controller that is equipped with the measuring device. By the wireless data communication, the data is transferred to the memory of notebook for further analysis. After roll extraction from mills, Portable Roll Scanner measure the roll profile and surface temperature simultaneously along the work roll face and display the results in the TFT color monitor of notebook. Portable Roll Scanner is useful at mill-side and roll grinding shop.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.48-52
• /
• 2004

Ultrasonic machining is effective for machining of extreme hard and brittle materials, including glass, ceramic, carbide, graphite. The major machining principle involves the direct hammering as well as the impact of abrasive panicles on the workpiece. Also, it involve cavitation erosion. The general workpiece is flat side. This study attempted micro hole machining of a curved surface of glass tube. Ultrasonic machining is fault of the slow machining speed. An experiment does and got 16 seconds validity machining time as increasing the processing speed. Moreover, entrance crack and surface roughness was similar both machining speed is slow and fast. Several micro hole of glass tube machined using one micro tool, but tool wear is infinitesimal.

• 한국생산제조학회지
• /
• 제9권2호
• /
• pp.119-124
• /
• 2000

In this paper based on geometric optics and geometric modeling aspheric surface of the side mirror mold with dead angle reduced have been designed and machined in a CNC machining center, Surface roughness of the mold was evaluat-ed by usin the surface shaping system. Surface generating simulation of a ball endmill process is investigated. Through the simulation based on the surface-shaping system 3-D engineered surfaces and properties of engineered surfaces are obtained, Computer simulation provides the effective working conditions through the prediction of geometric properties of engineered surfaces. The rear view mirror and room mirror play important role on the safe driving condition as a observation of environment but the rear view mirror can not provide complete information of driving environments due to the existence of the dead angle. The analysis on the shape of formed mirror shows that the proposed me？ improves range of a driver's sight.

• 한국공작기계학회:학술대회논문집
• /
• 한국공작기계학회 2004년도 춘계학술대회 논문집
• /
• pp.99-104
• /
• 2004

Micro/meso cutting is getting more important in the fields of precision machining technology. A micro-turning lathe is one of parts to consist the Micro Factory. It accepts stepwise motion actuators that are used for feeding system instead of the conventional mechanism. It is consisted of two Piezoelectric ceramics; one is for feeding the slider, and the other is for clamping the slider in the guide way of the body. The linearity and positional accuracy of the actuators are good enough for high precision motion. The spindle unit is operated with DC motor on the top of the slider. The motion is communicated with miniaturized linear encoder attached on each side of axis. A mono crystal diamond tool is used for cutting tool. This micro-lathe has been made a machining experiment to see the characteristics of micro-machining.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2001년도 하계학술대회 논문집
• /
• pp.764-767
• /
• 2001

Because using LB method, result that produce Arachidic acid and Stearic acid LB film and measure the accumulation characteristic and electrical characteristic is as following. Organic monolayers of surface of the water compression each 9 layer's LB film to slide glass and manufactured MIM device compressing molecular film only. Could confirm that accumulation was good seeing as absorption coefficient and SEM picture, AFM picture that prevent manufactured LB films. Formation of domain of coexistence form that prevent LB film is indefinite and distinction of border side was not clear, and could know that roughness appears greatly. Obtained current by applied voltage could know that is proportional almost, though Arachidic acid appeared as bulk of current that happen in equaler certification voltage than Stearic acid is less, this alkyl chain longer Arachidic acid that serving relations special quality is superior know can .

• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2004년도 Proceedings of ISRS 2004
• /
• pp.689-692
• /
• 2004

Hydrographic data obtained from several ship experiments have shown that internal waves are frequently observed in the East (Japan) Sea, mostly in the continental slopes located along the western side of the East Sea. It is well known that oceanic internal waves can be detected well in synthetic aperture radar (SAR) images. Interactions between surface capillary-gravity waves and horizontally varying surface currents induced by internal waves produce variations in sea surface roughness which can be detected by SAR. C-band SAR images from ERS, ENVISAT ASAR and RADARSAT have been used to study the characteristics of internal waves in the East Sea. The observed properties of internal waves from many SAR images were compared and verified from in-situ measurements and theories.

• KSTLE International Journal
• /
• 제3권1호
• /
• pp.17-22
• /
• 2002

Roughing of tool steel in its hardened state represents a real challenge in the die and meld industry and process improvement depends on research of tool material, coating technique, and lubrication. However, roughing of hardened steels generates extreme heat and without coolant flooding, tool material cannot withstand the high temperature without choosing the right tools with proper coating. This research conducted milling tests using coated ball end mills to study effects of cutting conditions and geometric parameters of ball end mills on the machinability of hardened tool steel. KP4 steel and STD 11 heat treated steels were used in the dry cutting as the workpiece and TiAIN coated ball end mills with side relief angle of 12$^{\circ}$ was utilized in the cutting tests. Cutting forces, tool wear, and surface roughness were measured in the cutting tests. Results from the experiments showed that 85 m/min of cutting speed and 0.32 mm/rev of feed rate were optimum conditions for better surface finish during rough cutting and 0.26mm/rev with the same cutting speed are optimum conditions in the finish cutting.

• 한국기계가공학회지
• /
• 제19권3호
• /
• pp.105-110
• /
• 2020

Alumina, a typical ceramic material used for semiconductors and display parts, is the subject of research and development efforts for mineral material processing. Alumina is extremely difficult to process since it is brittleness to either fine ceramics material. We have studied the shape of diamond particles and their use in machinability for alumina processing. Our study was carried out under various processing conditions, including cutting speed, table speed, and the surface roughness of the work piece. We also analyzed the wear characteristics of the tool by total cutting.

• 대한기계학회논문집B
• /
• 제25권8호
• /
• pp.1037-1045
• /
• 2001

The effect of hysteresis in saturated pool boiling of water from stainless-steel surfaces has been investigated experimentally. Several sets of test sections of different surface conditions, geometries, orientations, diameters, lengths, and water types were tested at atmospheric pressure. The experimental results show that hysteresis effects in pool boiling heat transfer are not significant, but some appreciable trends are observed in accordance with parameters change. At higher heat flux regions, the curve for heat flux decrease is shifted to the left side of the curve for heat flux increase. To clarify hysteresis in pool boiling and to give some improvement on published correlations, four empirical correlations are obtained in terms of tube diameter, surface roughness, and tube wall superheat.