• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2005.06a
• /
• pp.1644-1647
• /
• 2005

This study was aimed at evaluating the structural safety for rubber tired AGT system. Based on these, AGT system which was developed for first time in domestic is need to verify structural safety. So we measured the characteristics of guide-rail, switch rail, side wall in the constructed test track for rubber tired AGT system. Finally, all results of test showed that structural safety of the rubber tired AGT system.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.6
• /
• pp.477-480
• /
• 1998

In this paper, we investigated the liquid crystal(LC) alignment and generation of pretilt angle by using photo-alignment techniques on two kinds of polyimide(PI) surface, It was found that the uniform alignment for nematic(N) LC is obtained in a cell with slanted UV light irradiation on PI surface without side chain. We successfully observed that the pretilt angle of NLC is generated about $3^{\circ}$ with an incident angle of 70 degree on the PI surface without side chain. It is considered that the pretilt angle generation in NLC is attributed to interaction between the LC molecules and the polymer surfaces.

• Bulletin of the Korean Chemical Society
• /
• v.20 no.10
• /
• pp.1186-1194
• /
• 1999

Photoresponsive side chain polymers containing aminonitro azobenzene were synthesized for studying optically induced birefringence. Four different copolymers were prepared using methacrylate, a-methylstyrene, and itaconate monomer. Two copolymers are totally amorphous and the other two are liquid crystalline in nature. Trans-to-cis photoisomerization was observed under the exposure of UV light with UV-VIS absorption spectroscopy. Reorientation of polar azobenzene molecules induced optical anisotropy under a linearly polarized light at 532 nm. The dynamic parameters of optically induced birefringence let us compare the effect of polymeric structure on the rate of growth and decay of the birefringence. Besides the effect of glass transition temperature on the dynamics of photoinduced birefringence, we focused our interests on the geometrical hindrance of polar azobenzene molecules and cooperative motion of environmental mesogenic molecules in the vicinity of polar azobenzene moiety.

• Journal of Photoscience
• /
• v.1 no.1
• /
• pp.69-73
• /
• 1994

Sporangiophores (spphs) of Phycomyces blakesleeanus are positively phototropic to unilateral visible (blue) light over a range of fluence rates 10$^{-9}$ to 1 W/m$^2$. The maximal bending angle is always 70-75$\circ$ from the vertical. Many mutants with abnormal phototropism have been isolated. Complementation tests revealed that the genetic grouping is completely consistent with the phenotypic classification scheme, based on sensory responses other than those to light. The spph of the piloboloid mutant, the growth zone of which gradually ceases elongation but expands spherically, and the $\beta$-carotene-overproducing mutant show negative phototropism, in contrast to the wild type spph. We hypothesized that the phototropic orientation of spph is determined by the ratio of the maximal light fluenee rate at the proximal side to that at the distal side of the spph. Based on this hypothesis, we found that the maximal bending angle was larger in thin spphs than in thick ones, and larger in spphs containing smaller amount of $\beta$-carotene than in carotene-rich spphs. In addition to our hypothesis, gravitropic experiments revealed that the maximal bending angle of the wild type spph results from a balance among positive phototropism, negative gravitropism, and the optical properties of the spph. For further advancement of this study, we developed a mutant with a high proportion of uninucleate spores, and designed an efficient microinjection method for obtaining transformants.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.32 no.4
• /
• pp.287-295
• /
• 2019

Privacy films are typically manufactured by combining black resin and transparent louver-shaped patterns. The use of black resin results in excellent light-shielding. However, black resin can reduce the transmittance of privacy films at the front viewing angle. In this study, we applied $SiO_2/SiON$ multi-layer thin films on a privacy film to maintain transmittance at the front viewing angle and improve light-shielding at the side viewing angle. We determined the optimum combination of thicknesses of the $SiO_2/SiON$ multi-layer stacks to increase the overall transmittance; the light shielding could be maximized at the side viewing angle.

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2007.11a
• /
• pp.179-182
• /
• 2007

Recently, the circuits of fluorescent light-switches are separated for window-light, middle-lights, or corridor-light, etc in most offices and classrooms in this country. Although it is clean and shiny - more than standard intensity of illumination, it is common that fluorescent lights on the side of window are lighted. In this case, we can use a fluorescent light with a sensor, which is turned on and off automatically according to the amount of sunlight. I think that this plan can save energy, reduce the budget, and increase the effect of education. and so I studied on this plan.

• Journal of Photoscience
• /
• v.3 no.3
• /
• pp.133-136
• /
• 1996

Calcium modulates the activity of guanylate cyclase and plays a key role in dark and light adaptation in the visual system. We have measured the Ca$^{2+}$, K$^+$ and Na$^+$ concentration in dark and light adapted bullfrog's (Rana catesbeiana) vitreous humor by using the atomic absorption spectrophotometer. The calcium concentration of the light adapted bullfrog's vitreous humor was higher than that of the dark adapted bullfrog's vitreous humor. This means that ion activity between the photoreceptor and vitreous humor side is light dependent and we have found that a Ca$^{2+}$ channel and Na$^+$ - Ca$^{2+}$ exchanger exist in the vitreous humor.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2003.05a
• /
• pp.7-12
• /
• 2003

In scrapped material field, about ten millions ton of waste plastic materials are produced in korea. However recycling rate of waste plastic materials have above 25%. Therefore, it is urgently needed that they are used as recycled materials in order to prevent environment pollution and grain economic profits. In this paper, physical and mechanical properties of light weight concrete using waste plastic materials for aggregates are described in order to develop a light weight concrete with the aggregate made from waste plastic goods, it was carried out many experiments on mix proportion and strength. According to the experimental results, high-strength mortar was necessary to make light weight concrete using aggregate of waste plastic materials. Especially, considering the side of recycling of plastic wastes, it is recommended that recycled aggregates made from waste plastic materials is applied to light weight concrete.

• Journal of Information Display
• /
• v.13 no.3
• /
• pp.119-123
• /
• 2012

In this work, we report on a new monitoring method for an organic light-emitting diode (OLED) panel for lighting by optical sensing of the wave-guided light in the substrate. Using microlens array films, the wave-guided light was extracted into the edge or back side of the panel to be monitored by a photodiode. The luminance of the extracted light was measured as linearly proportional to the front light. Thus, by converting the extracted light into photo voltage, monitoring the luminance change occurring in the OLED is possible. Based on the results and concepts, we have proposed a photodiode-equipped driving circuit which can generate compensated driving current for uniform luminance of OLED panels.

• Journal of Technologic Dentistry
• /
• v.42 no.2
• /
• pp.65-71
• /
• 2020

Purpose: To know the transmittance of light when wearing shading goggles and to protect eyes from blue light emitted from dental scanner when using CAD/CAM works or inducing polymerization reactions of dental resin with curing unit and infrared light occurred when melting Dental precious metal and non-precious metal alloys. Methods: By measuring and comparing the average transmittances of blue light, visible light and infrared ight by using UV-Vis Spectrophotometer analysis measuring instrument, I compared 3 GREEN Color Goggles worn when casting Dental precious metal and non-precious metal alloys, and compared each of YELLOW, ORANGE Color Goggles worn when using Dental CAD/CAM scanners and Light Curing(LED) the Dental resin. Results: In blue light range, YELLOW Color Goggles are more effective than ORANGE Color Goggles. In infrared light range, No.12 Goggles are more effective than No.10 and No.11 Goggles. Conclusion: When wearing blue light shading goggles to avoid harmful blue light occurred in using dental scanner and curing light, and when wearing infrared light shading goggles to avoid harmful infrared light during casting, to avoid the Side Effects like transmittance rate of blue light and infrared light goggles becomes too high to block appropriate amount of harmful light or too low that causing lower image clarity.