• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2001년도 춘계학술발표대회 개요집
• /
• pp.228-231
• /
• 2001

Elastic-plastic fracture toughness $J_{1c}$ can be used as an effective design criterion in elastic plastic fracture mechanics. Most of these systems are operated at high temperature and $J_{1c}$ values are affected by temperature. therefore, the $J_{1c}$ valuse at high temperature must be determined for use of integrity evaluation and designing of such systems. Elastic-plastic fracture toughness $J_{1c}$ tests were performed on SA516 carbon steel plate and test results were analyzed according to ASTM E 813-8, ASTM 1813-89. Safety and integrity are required for reactor pressure vessels vecause pthey are operated in high temperature. there are single specimen method, which used as evaluation of safety and integrity for reactor pressure vessels. In this study, elastic-plastic fracture toughness$(J_{1c})$ and $J-\Delta{a}$ of SA 516/70 steel used as reactor pressure vessel steel are measured and evaluated at room Temperature, $150^{\circ}C$, $250^{\circ}C$ and $370^{\circ}C$ according to unloading compliance method.

• 한국해양공학회지
• /
• 제15권2호
• /
• pp.99-104
• /
• 2001

Elastic-plastic fracture toughness $J_{lc}$ can be used as an effective design criterion in elastic plastic fracture mechanics. Most of these systems are$J_{lc}$ $J_{lc}$ value at high temperature must be determined for use of integrity evaluation and designing of such systems. Elastic-plastic fracture toughness $J_{lc}$ tests were performed on SA516/70 carbon steel plate and test results were analyzed according to ASTM E 813-87, ASTM E 813-89 and ASTM E 1152-87.safety and integrity are required for reactor pressure vessels because, they are operated in high temperature. There are single specimen method, which used as evaluation of safety and integrity for reactor pressure vessels. In this study, elastic-plastic fracture toughness($J_{lc}$) and J-$\Delta$a of SA 516/70 steel used as reactor pressure vessel steel are measured and evaluated at room temperature, 150$^{\circ}C $, 250$^{\circ}C $ and 370$^{\circ}C $ according to unloading compliance method.

• Journal of Advanced Marine Engineering and Technology
• /
• 제31권6호
• /
• pp.753-760
• /
• 2007

For protection of the cylinder wall of the ball mill for grinding raw ore. the inner side of the cylinder is covered with rubber liner. The rubber is easily worn down because the rubber relatively soft compared with raw ore. So the rubber liner in the ball mill cylinder must be replaced almost every year and the cost for replacing rubber liner formidable. In this paper, for reducing or excluding the cost of replacing rubber liner the basalt liner is designed. The basalt materials are generally harder than raw ore and the basalt liner in the ball mill does not wear down and so it can be used almost permanently. The concave surfaces are made on the liner of the ball mill and the liner in the cylinder wall plays also the role of raising the steel balls mixed in the raw ore. The section profiles of the concave surface have an important effect on the performance of the ball mill. The deep concave grooves raise the steel balls to high levels and give the large potential energy to the steel balls impacting to the raw ore. But if the concave grooves are too deep. the steel balls raised too high by the concave grooves fly along the parabolic path and reach to the other side of cylinder wall and so the steel balls do not play the roles of grinding the raw ore. The forces acting to a steel ball in a concave groove of the cylinder liner are also analyzed in this paper. The formulas calculating the height and the impact point of the steel ball are introduced and presented. Based to these formulas, the optimum section profiles of the basalt liner are presented.

• 대한용접접합학회:학술대회논문집
• /
• 대한용접접합학회 2009년 추계학술발표대회
• /
• pp.55-55
• /
• 2009

FGB(Flexible Glasswool Backing) Submerged Arc Welding has been one of the main welding processes for one side butt welding in shipbuilding industries, which can efficiently improve the welding productivity by the addition of a supplementary filler metal into the molten weld pool. As recent ships have become larger in size, the application of high tensile and higher grade of steels has been continuously increased. Single pass FGB SA welding process accompanies such a high heat input when welding thick plates that the mechanical properties of weld metal can be dramatically degraded. This study has been performed in order to obtain high toughness and tensile properties of high heat input FGB SA welds, and to evaluate the effect of alloy elements on their mechanical properties. To complete welding 25mm-thick EH36 grade steel plate by single pass, 1.2mm diameter and 1.0mm long cut wires has been distributed in the groove before welding, and three different test coupons have been made using C-1.5%Mn, C-1.8%Mn-0.5%Mo, and C-1.4%Mn-1.7%Ni cut wires to investigate the influence of nickel(Ni) and molybdenum(Mo) on the mechanical properties of welds. Test results showed that the addition of Ni and Mo effectively promotes the formation of Acicular Ferrite(AF), while significantly reducing the amount of Grain Boundary Ferrite(GBF) in weld metal microstructures, which resulted in a beneficial effect on low temperature impact toughness and strength.

• 대한치과보철학회지
• /
• 제40권3호
• /
• pp.296-305
• /
• 2002

The main disadvantage of cement-retained implant restorations is their difficulty in retrievability. Advocates of cemented implant restorations frequently state that retrievability of the restoration can be maintained if a provisional cement is used. The purpose of this study was to find the optimal properties of provisional luting cements and the surface treatment of abutments in single implant abutment system. 30 prefabricated implant abutments, height 8mm, diameter 6mm, 3-degree taper per side, with light chamfer margins were obtained. Three commercially available provisional luting agents which were all zinc oxide eugenol type ; Cavitec, TempBond and TempBond NE were evaluated. No cement served as the control. TempBond along with vaseline, a kind of petrolatum (2:1 ratio) was also evaluated. Ten out of thirty abutments were randomly selected and abutment surfaces were sandblasted with $50{\mu}m$ aluminum oxide. Another ten abutments were sandblasted with $250{\mu}m$ aluminum oxide. A vertical groove, 1 mm deep and 5mm long was cut in each twenty abutments. Ten of them were sandblasted with $50{\mu}m$ aluminum oxide. The full coverage casting crowns were cemented to the abutments with the designated provisional luting agent. Specimens were stored in distilled water at $37^{\circ}C$ for 24 hours. Each specimen was attached to a universal testing machine. A crosshead speed of 0.5mm/min was used to apply a tensile force to each specimen. Within the limitations of this in vitro study, the following conclusions were drawn: 1. Tensile bond strength of provisional luting cements in no surface treatment decreased with the sequence of TempBond NE, TempBond, Cavitec, TempBond with vaseline, no cement. 2. Tensile bond strength more increased by surface treatment. Sandblasting with $250{\mu}m$ aluminum oxide exhibited the highest tensile bond strength in the abutment cemented with TempBond NE and sandblasting with $50{\mu}m$ aluminum oxide exhibited the highest tensile bond strength in cemented with TempBond. 3. In the aspect of a groove formation, tensile bond strength significantly increased in TempBond with vaseline only and the others had no significant effect on tensile bond strength.

• Journal of Advanced Marine Engineering and Technology
• /
• 제37권5호
• /
• pp.461-466
• /
• 2013

본 논문은 조선해양 구조물 주판의 맞대기용접 수축에 대한 특성을 연구하였다. 주판의 맞대기 용접은 입 열과 냉각과정에서 수축 변형이 일어나 최종 완성된 모재의 치수와 설계 치수가 다르게 된다. 이는 선박의 블록 생산 품질 불량으로서 교정 작업이 필요하며 생산성 향상의 저해요인이다. 이에 대형 구조물 주판의 맞대기용접 수축 변형에 관한 실험을 통하여 I, Y, V 형상의 용접잔류응력 수축 변형 데이터를 확보하고 두께 11 t ~ 21.5 t 범위에서는 1 ~ 2 mm의 한정된 범위의 수축 량이 균일하게 나타나는 특징과 용접부의 열전달 영향이 Seam Line 한쪽을 기준으로 최대 약 1000 mm 이내에 국한되어 모재의 자중이 수축 량에 미치는 영향은 크지 않았고 또한 수축 변형을 최소화하기 위해 설계단계에서 Groove 형상에 따라 수축마진을 다르게 적용해야 함을 알 수 있었다.

• 한국가스학회지
• /
• 제21권4호
• /
• pp.70-75
• /
• 2017

본 연구에서는 차단기능형 수평식 가스밸브와 기존 수직식 가스밸브의 변형거동 안전성을 FEM으로 해석하였다. FEM 해석결과에 의하면, 차단기능형 수평식 가스밸브의 나사부와 가스방출구에 가스내압이 작용할 때 밸브몸체의 우측 끝단부에서 최대 변형량 $4.4{\mu}m$가 발생하였다. 두 번째로 큰 변형량 $2.9{\mu}m$는 안전밸브가 설치된 포트의 끝단부에 형성된 것으로 나타났다. 이렇게 작은 변형량이 발생한 것은 나사부, 가스방출구, 스템 및 스핀들 축이 장착되는 포트, 안전밸브 포트로 구성되는 수평식 가스밸브의 평형이 잘 이루어지도록 설계되었기 때문이다. 반면에 나사부와 가스방출구에 가스내압이 작용할 때, 기존 차단기능형 수직식 가스밸브의 상단부에서 최대 변형량 0.076mm가 형성된 것으로 나타났다. 가스유출구의 좌측 끝단부에서 두 번째로 큰 최대 변형량 0.055mm가 발생하였다. 이러한 변형량은 차단기능형 안전장치의 그루브에 삽입된 오링의 밀봉간극에 영향을 미칠 가능성이 높다. 따라서 본 연구에서는 LPG 용기용 가스밸브의 가스누출을 완벽하게 차단할 수 있는 메커니즘을 갖춘 차단기능형 수평식 가스밸브가 수직식 가스밸브에 비해 우수하다할 수 있다.

• 한국가스학회지
• /
• 제2권4호
• /
• pp.42-46
• /
• 1998

소형 시험편 기술은 최소량의 재료를 사용하여 그 재료의 물리적인 거동을 특성화할 수 있기 때문에 산업설비로부터 많은 재료를 수집할 수 없는 경우에 유용한 방법이다. 본 연구에서 사용한 재료는 화력발전소 터빈로터 소재로 많이 사용되고 있는 1Cr-1Mo-0.25V강이었으며, $^630{\circ}C$에서 등온열화처리하여 5종류의 가속 열화 모사재를 만들었다. 충격시험에는 표준 시험편과 소형 시험편이 사용되었으며, 일부 소형 시험편에 소성 구속을 증가시키기 위해 측면흠을 만들어 넣었다. 표준 시험편과 소형 시험편의 충격특성을 비교하였으며 크기효과를 고찰하였고, 소형 시험편의 연성취성천이온도와 표준 시험편의 연성취성천이온도와의 상관관계를 만들었다. 따라서 소형 시험편의 충격시험결과로부터 표준 시험편의 충격특성을 추정하는 것이 가능하게 되었다.

• 한국펄프종이공학회:학술대회논문집
• /
• 한국펄프종이공학회 2003년도 춘계학술발표논문집
• /
• pp.70-79
• /
• 2003

Paper coating can give smoothness surface and good printability to uncoated paper. Macro roughness of base paper would be decreasing its groove and grit in view of side. Nevertheless its improving effect for paper, some kind of problem is showing in the fine coated paper. Especially, back trap mottle is one of serious problems in printing with fine coated paper. Printers can not adjust conditions to overcome the problem. Also large amounts of paper can be rejected. There are many factors that influence back trap mottle. However it is not clear what the important parameters are in back trap mottle. Back trap mottle has some relationship with ink setting but good guidelines are not clear. Back trap mottle has been linked to non-uniform ink setting. We do not know how much variation in setting we can tolerate. Other mottle issues such as micro-picking and ink refusal are still common. This paper was prepared to identify correlation with ink setting and delta ink density obtained from experiment and then tried to find out some relationships with ink setting and back trap mottle. Basically fine calcium carbonate and ciay was used for main components and coarse calcium carbonate was mixed in two fine pigments to change its porosity and ink acceptance. Micro ink tack force at KRK printing tester was adapted to measure ink setting rate. KRK units were used for back trap mottle simulation and two printed samples were prepared to check delta ink density. Clay base coating has more fast ink setting time than calcium carbonate's though smoothness of clay was better than calcium carbonate. It could be explained by that clay has finer pore in its coating than calcium carbonate. DID(delta ink density) has shown a good correlation with ink setting time from micro ink tack. The total pore volume of coating layer did not match with ink setting and DID. From the results we might conclude coating that has fine pore size around 0.05 ${\mu}m$ can be exposed to high possibility of back trap mottle.