• Journal of the Korean Institute of Telematics and Electronics
• /
• v.18 no.4
• /
• pp.21-26
• /
• 1981

SnO2/n-Si and ITO/n-Si SIS solar cells have been fabricated ty mears of electron-beam deposition. The optimum oxidation and heat-treatment condition for SnO2/n-Si cells and ITO/n-Si cells are 50$0^{\circ}C$-5min., 30$0^{\circ}C$-10min., and 50$0^{\circ}C$-5min., 30$0^{\circ}C$-20min. respectively. The open-circuit Voltage(Voc), short-circuit current density(Jsc), fill factor(FF), and efficiency (η) under AMI(100mW/$\textrm{cm}^2$) illumination were 0.4V, 34mA/$\textrm{cm}^2$, 0.44, and 6.0%(active area efficiency, 6.9%) for SnO2/n-Si solar cells, and 0.44V, 36mA/$\textrm{cm}^2$, 0.53, and 8.45%(active area efficiency, 9.71%) for ITO/n-Si solar calls.

• Journal of Sensor Science and Technology
• /
• v.1 no.1
• /
• pp.5-12
• /
• 1992

We have fabricated a-Si:H multilayer for contact-type linear image sensor by means of RF glow discharge decomposition method. The ITO/i-a-Si:H/Al structure has relatively high dark current due to indium diffusion and carrier injection from both electrodes, resulting in low photocurrent to dark current. To suppress the dark current and to enhance interface electric field between ITO and i-a-Si:H film we have fabricated ITO/insulator/i-a-S:H/p-a-S:H/Al multilayer film with blocking structure. The photocurrent of ITO/$SiO_{2}(300{\AA})$/i-a-Si:H/p-a-Si:H($1500{\AA}$)/Al multilayer sensor with 5V bias voltage became saturated at about 20nA under $20{\mu}W/cm^{2}$ light intensity, while the dark current was less than 0.1nA. To increase the light generation efficiency we have adopted ITO/$SiO_{x}N_{y}(300{\AA})$/i-a-Si:H/p-a-Si:H($1500{\AA}$)/Al structure, showing photocurrent of 30nA and dark current of 0.08nA with 5V bias voltage. Also the spectral photosensitivity of the multilayer was enhanced for short wavelength visible region of 560nm, compared with that of the a-Si:H monolayer of 630nm. And its photoresponse time was about 0.3msec with the film homogeneity of 5% deviation.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.23 no.1
• /
• pp.24-28
• /
• 2010

We have proposed an Buffer layer to improve the transmittance of ITO. Here, $SiO_2$ and $TiO_2$ were selected as the Buffer layer coating material. The structures of Buffer layer were designed in ITO/$SiO_2/TiO_2$/Glass and ITO/Glass/$TiO_2/SiO_2$. Then, these materials were deposited by ion-assisted deposition system. Transmittances of deposited ITO were 86.14 and 85.07%, respectively. These results show that the proposed structure has higher transmittance than the conventional ITO device.

• Journal of Korean Ophthalmic Optics Society
• /
• v.5 no.1
• /
• pp.7-11
• /
• 2000

The anti-reflective anti-static (ARAS) optical film is designed using absorbent materials such as ITO, $TiN_xW_y$, Ag by Essential Macleod program. [air ${\mid}TiN_xW_y{\mid}SiO_2{\mid}$ glass] two layer shows wide-band AR coating in the wavelength range of 450~700 nm. The reflectivity, transmittance of this coating are below 0.5%, about 75%, respectively. [air $SiO_2{\mid}TiO_2{\mid}SiO_2{\mid}$, ITO glass] layer can adjust reflectance of below 0.5% with above 97% transmittance. In the [air ${\mid}SiO_2{\mid}TiO_2{\mid}SiO_2{\mid}$ Ag glass] layer, the transmission can be controlled at above 96% with reflectance of 1~2%.

• Analytical Science and Technology
• /
• v.6 no.2
• /
• pp.239-246
• /
• 1993

The structure of $(BaSr)TiO_3$ thin film deposited on ITO coated glass, bare glass and (100) Si substrates was not changed, but the crystallinity was improved by the polycrystalline ITO layer and (100) Si substrate. The composition of $(BaSr)TiO_3$ thin film deposited on ITO coated glass was nearly stoichiometric ((Ba+Sr)/Ti=1.08~1.09) and very uniform through all deposition process. But as the deposition temperature increases, the interdiffusion between grown thin film and ITO layer and between ITO layer and base glass is severer. $(BaSr)TiO_3$ thin film deposited on ITO coated glass substrate was highly transparent. The refractive index($n_f$) of $(BaSr)TiO_3$ thin film deposited on ITO coated glass was 2.138~2.286 as a function of substrate temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.11 no.9
• /
• pp.711-717
• /
• 1998

BST(70/30) and BST(50/50) thin films were prepared by Sol-Gel method and studied about the microstructural and dielectric properties with Pt and ITO bottom electrodes. The stock solution was synthesized and spin coated on the Pt/Ti$SiO_2$/Si and Indium Tin Oxide(ITO)/ glass substrate. the coated films were dries at 350$^{\circ}C$ for 10 minutes and annealed at $750^{\circ}C$ for 1 hour for the crystallization. The thin films coated on ITO substrate were crystallized easily and the packing density and roughness of surface were better that those of films coated on Pt substrates. In the BST(50/50) composition the structural properties were similar to the BST(70/30) composition and grain size were decreased with increasing the contents of Sr. The dielectric constant was higher in the BST(50/50) composition compared with the BST(70/30) composition. Using the ITO substrate, the dielectric constant was higher than the Pt substrate while the dielectric loss was showed a reverse trend. The dielectric constant with and increase of temperature was decreased slowly.

• Journal of Information Display
• /
• v.2 no.1
• /
• pp.38-42
• /
• 2001

Thin films of $In_2O_3-SnO_2$(ITO), $SnO_2$, and $SiO_2$ were prepared on the PET substrate by DC magnetron roll sputtering. 135 nm thick ITO film on $SiO_2$/PET substrate has sheet resistance as low as 55 ${\Omega}/square$ and transmittance as high as 85%. $H_2O$gas permeation through the film was 0.35 g/$m^2$ in a day. These properties are enough on optical film for the plastic LCD substrate or touch panel. Both refractive index and sheet resistance of ITO was found to be very sensitive to $O_2$ flow rate. Oxygen flow conditions have been optimized from 4 to 5 SCCM at $10^{-3}$torr. It is also shown that both thickness of $SnO_2$ and refractive index of $SiO_2$ decrease as $O_2$ flow rate increases.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.06a
• /
• pp.307-308
• /
• 2009

We have proposed an index matching film to improve the emitting efficiency of green OLED. Here, SiO2 and TiO2 were selected to coat the green OLED. The structures of index matching film were designed in G1ass/TiO2/SiO2/ITO and SiO2/TiO2/Glass/ITO. Then, these materials were deposited by ion-assisted deposition system. Transmittances of deposited devices were 86.14 and 85.07 %, respectively.

• Proceedings of the Korean Ceranic Society Conference
• /
• 2000.10a
• /
• pp.158.2-158
• /
• 2000

• Journal of the Korean Vacuum Society
• /
• v.7 no.1
• /
• pp.17-23
• /
• 1998

$Pb(Fe_{0.5}Nb_{0.5}O_3(PFN)$ thin films were prepared by rf magnetron co-sputtering method on $SiO_2/Si$, ITO/glass, and $Pt/Ti/SiO_2/Si$ substrates and post-annealed at the $N_2$ atmosphere by RTA(rapid thermal annerling). The degree of crystallinity of PFN films was identified on various substrates. Electrical properties of PFN films was characterized for $Pt/PFN/Pt/Ti/SiO_2/Si$ structure. The composition of PFN films was estimated by EPMA (electron probe micro analysis). PFN films would be crystallized better to perovskite phase on ITO/glass substrate than $SiO_2/Si$ substrate. This may be induced by the deformation of Pb deficient pyrochlore phase due to Pb diffusion into $SiO_2/Si$ substrate. PFN films on $Pt/Ti/SiO_2/Si$ substrate. PFN films with 5-10% Pb excess were crystallized to perovskite phase from $500^{\circ}C$ temperature. In summary, we show that Pb composition and annealing temperature were critically influenced on crystallinity to perovskite phase. When PFN film with 17% Pb excess was annealed at $600^{\circ}C$ at the $N_2$ atmosphere for 300kV/cm and 88. Its remnant polarization coercive field $2.0 MC/cm^2$ and 144kV/cm, respectively.