• KIEE International Transactions on Electrophysics and Applications
• /
• v.12C no.4
• /
• pp.220-224
• /
• 2002

The electromagnetic properties and thermal behavior of Mn-Zn ferrite cores for the blocking filter of PLC application were investigated as the function of additives. The highest density and permeability were 4.98 g/㎤ and 8,221, respectively and were obtained to the specimen with composition of MnO 24 mol%, ZnO 25 mol% and Fe$_2$O$_3$51 mol%, added MoO$_3$ of 400 ppm, SiO$_2$ of 100 ppm, and CaO of 200 ppm. The uniform grains were organized, and the microstructures were compacted due to reduction of pores in the specimen. The permeability was increased up to 13,904 as the temperature of specimen increased to 110。C. However, it was decreased precipitously under 100 over 110。C. The exothermic behavior was observed in the frequency range from 1 kHz to 1 MHz, and the maximum temperature of specimen was 102。C at 1 MHz. In the consequence, the Mn-Zn ferrite core developed in this research will maintain the stable electromagnetic properties since the temperature of ferrite core rose to 93 。C in the range of 100 kHz to 450 kHz bandwidth qualified for PLC. The blocking filters were designed for single phase and three phases using the in-line and non-contact core. The best attenuation ratios of -46.46 dB and -73.9 dB were measured in the range of 100 kHz to 450 kHz bandwidth, respectively.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.33 no.6
• /
• pp.234-243
• /
• 2023

Zinc crystals of ZnO and SiO₂ in glaze raw materials, developed according to composition and firing requirements, are preferred because of their high decorative properties. However, most zinc crystal glazes have a high firing temperature and a narrow firing temperature range, making it difficult to use them as commercial glazes in ceramics. Therefore, in this study, it was expected that the firing temperature of a typical zinc crystal glaze could be lowered to below 1270℃ by using the eutectic effect through mixing frit, the main raw material used in manufacturing zinc crystal glaze. As a result, not only was the formation temperature of zinc crystals lower in the mixed frit glaze, but also the firing temperature range was widened to 1230~1270℃, making it possible to develop a glaze that produces crystals stably. The firing temperature was lowered to 1230~1250℃ and the holding temperature during cooling was lowered to about 950℃, resulting in the development of an economically effective glaze. When using a combination of frit, it has been shown that the holding temperature during cooling affects the recrystallization of zinc crystals depending on the composition of the glaze, and the crystal structure can be adjusted at this time. Additionally, the amount and shape of crystals can be controlled by using a nucleating agent.

• Korean Journal of Crystallography
• /
• v.11 no.3
• /
• pp.167-172
• /
• 2000

CaTiO₃:Pr phosphor thin films were prepared on Si(100), ZnO/glass, Corning glass and ITO/glass by rf magnetron reactive sputtering. The effects of deposition parameters such as oxygen partial pressure, substrate temperature, and annealing conditions on crystallinity and compositional variation of the films were investigated. PL spectra of CaTiO₃:Pr phosphor thin films exhibited red regime peaking at 613 nm and enhanced PL intensity was observed for the film annealed in vacuum atmosphere as compared to the deposit annealed in N₂ environment.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2015.08a
• /
• pp.208.1-208.1
• /
• 2015

최근, 차세대 투명 디스플레이 구동소자로서 산화물 반도체를 이용한 Transparent Amorphous Oxide Semiconductor (TAOS) 기술이 큰 주목을 받고 있다. 산화물 반도체는 기존의 a-Si에 비해 우수한 전기적인 특성과 낮은 구동전압 그리고 넓은 밴드 갭으로 인한 투명성의 장점들이 있다. 그리고 낮은 공정 온도에서도 제작이 가능하기 때문에 유리나 플라스틱과 같은 다양한 기판에서도 박막 증착이 가능하다. 하지만 기존의 furnace를 이용한 열처리 방식은 낮은 온도에서 우수한 전기적인 특성을 내기 어려우며, 공정 시간이 길어지는 단점들이 있다. 따라서 본 연구에서는 산화물 반도체중 In-Ga-Zn-O (IGZO)와 In-Sn-O(ITO)를 각각 채널 층과 게이트 전극으로 이용하였다. 또한 마이크로웨이브 열처리 기술을 이용하여 기존의 열처리 방식에 비해 에너지 전달 효율이 높고 짧은 시간동안 저온 공정이 가능하며 우수한 전기적인 특성을 가지는 투명 박막 트랜지스터를 구현 하였다. 본 실험은 glass 기판위에서 진행되었으며, RF sputter를 이용하여 ITO를 150 nm 증착한 후, photo-lithography 공정을 통하여 하부 게이트 전극을 형성하였다. 이후에 RF sputter를 이용하여 SiO2 와 IGZO 를 각각 300, 50 nm 증착하였고, patterning 과정을 통하여 채널 영역을 형성하였다. 또한 소자의 전기적인 특성 향상을 위해 마이크로웨이브 열처리를 1000 Watt로 2 분간 진행 하였고, 비교를 위하여 기존 방식인 furnace 를 이용하여 N2 분위기에서 $400^{\circ}C$로 30분간 진행한 소자도 병행하였다. 그 결과 마이크로웨이브를 통해 열처리한 소자는 공정 온도가 $100^{\circ}C$ 이하로 낮기 때문에 glass 기판에 영향을 주지 않고 기존 furnace 열처리 한 소자보다 전체적으로 전기적인 특성이 우수한 것을 확인 하였다.

• Journal of the Korean GEO-environmental Society
• /
• v.8 no.2
• /
• pp.5-9
• /
• 2007

This study carried out to investigate the removal capacity of heavy metals such as Cu (II), Zn (II) and Cd (II) dissolved in aqueous solution in the soils collected from Hyeon-Dong (HD), San-seong (SS), Keum-chon (KC) and Keum-Hac (KH) located in the upper Banbyun stream. The pH of all the soils was weak alkali such as 8.8 9.2. According to the analysis of chemical composition of the soils, the amount of $SiO_2$, $AlO_2$ and CaO were similar in all tested soils. However, the amount of $K_2O$, $FeO_3$ and MgO were different from each soil. The XRD measurement with these soils showed that quartz and feldspar were presented in all tested soils, and the distribution of kaoline, illite, montmorillonite, vermiculite and calcite were different from each soil. The results of the removal capacity of heavy metals indicated that all the soils had more than 98% of the removal efficiency of Cu (II), Zn (II) and Cd (II), and among the heavy metals, Cu (II) was removed the most effectively. These results suggested that the soils collected from the upper Banbyun stream have the high removal capacity of heavy metals, and these soils could be used for the banking a river around the abandoned mine area, containing the higher concentrations of heavy metals than the usual stream.

• Journal of the Korean Ceramic Society
• /
• v.16 no.2
• /
• pp.69-76
• /
• 1979

This study attempted to characterize the powder and sintered specimen of Mn-Zn ferrite that was prepared by Hot Petroleum Drying Method. The results of the experiment were as follows: 1. The mixed sulfate powder prepared by Hot Petroleum Drying Method was homogeneous and very reactive. The ferrite formation of this powder occurred at lower temperature than the one prepared by Sulfate Dry Mixing Method. 2. The calcined oxide powder prepared by Hot Petroleum Drying Method was found to be agglomerated, and therefore it was very difficult to compact this powder. 3. The sintered density was 4.95g/㎤, 97% of the theoretical density, when the specimen was prepared by Hot Petroleum Drying method, calcined at 90$0^{\circ}C$ in air for 3h, sintered at 1,30$0^{\circ}C$ in air for 3h, and then cooled in nitrogen. 4. The discontinuous grain growth occurred at lower temperature in the specimen prepared by Hot Petroleum Dyring Method than in the one prepared by Sulfate Dry Mixing Method. The discontinuous grain growth was considered to be due to the presence of liquid formed by addition of CaO and $SiO_2$.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.78-78
• /
• 2011

수열합성법을 이용하여 Si(111) 기판에 ZnO 박막을 성장하였다. ZnO 박막의 성장을 위한 씨앗층은 plasma-assisted molecular beam epitaxy (PA-MBE)를 이용하였다. 씨앗층의 표면 거칠기(root-mean-square roughness)는 2.5 nm이고, 씨앗층 위에 성장된 ZnO 박막은 다양한 크기의 입자들로 이루어져 있었으며 두께는 약 $1.8{\mu}m$로 매우 일정하였다. 배향성을 알아보기 위하여 texture coefficient (TC)를 계산해 보았다. TC(100)과 TC(200)은 a-축 배향성을, TC(002)는 c-축 배향성을 나타내는데, c-축으로 더 우세한 배향성(99.5%)을 보였다. TC 비율(TCa-axis/TCc-axis)은 열처리 온도를 $700^{\circ}C$까지 올렸을 때, 점차적으로 증가하였고, 그 이상의 열처리 온도(< $900^{\circ}C$)에서는 급격히 감소하였다. 잔류응력과 Zn와 O의 bond length도 유사한 경향을 보였다. $700^{\circ}C$까지 열처리 온도가 증가함에 따라, 잔류응력은 증가하였고 bond length는 감소하였다. Near-band-edge emission (NBE)의 피크 강도는 열처리 온도가 $700^{\circ}C$까지 증가함에 따라 점차적으로 증가하였다. 열처리 온도가 $800^{\circ}C$ 이상 증가함에 따라 deep-level emission (DLE)가 적색편이(red-shift)하였다. $700^{\circ}C$로 열처리를 한 ZnO 박막이 가장 우세한 (002)방향의 배향성을 보였을 뿐만 아니라 가장 큰 발광효율 증가를 보였다.

• Journal of Environmental Health Sciences
• /
• v.20 no.1
• /
• pp.62-67
• /
• 1994

Introduction : Recently, water and environmental pollution becomes serious social problem and high technology makes this pollution accelerate. Hydrogen sulfide, the main subject of our research, is one of the most dangerous air pollutant like SO$_x$ and NO$_x$. The major contaminant in coal gasification is H$_2$S, which is very toxic, hazardous and extremely corrosive. Therefore, control of hydrogen sulfide to a safe level is essential. Although commercial desulfurization process called liquid scrubbing is effective for removal of H$_2$S, it has drawbacks, the loss of sensible heat of the gas and costly wastewater treatment. Many investigations are carried out about high-temperature removal ol H$_2$S in hot coal-derived gas using metal oxide or mixed metal qxide sorbents. It was reported that ZnO was very effective sorbent for H2S removal, but it has big flaw to vaporize elemental zinc above 600\ulcorner \ulcorner As alternative, metal oxides such as CaO, $Fe_2O_3$, TiO$_2$ and CuO were added to ZnO. Especially, different results are reported for $Fe_2O_3$ additive. Tamhankar et al. reported SiO$_2$ with 45 wt% $Fe_2O_3$ sorbent is favorable for removal of H$_2$S and regeneration.

• The Korean Journal of Ceramics
• /
• v.2 no.1
• /
• pp.33-38
• /
• 1996

In thick film resistors, the characteristics of the frit and the reaction between glass frit and conductor material play an important role for their electrical properties. In this study, various glass frits in the system of $60RO{\cdot}20SiO_2$ $15B_2O_3{\cdot}5Al_2O_3$(RO=PbO, ZnO, CdO; mole%) were mixed with $RuO_2$ and coated on 96% alumina substrate. Only the glass frit containing PbO was reacted with $RuO_2$in$RuO_{2+}$-thick film resistor and produced the new crystalline phase of $Pb_2Ru_2O_{65}$. Their electrical resistivities strongly depend on the amount of $Pb_2Ru_2O_{65}$ crystalline phase obtained, which varied with firing temperature. The sheet resistivities of these resistors were varied from $10^3\; to\; 10^6\;{\Omega}/{\Box}$ depending on heat treatment, and the absolute value of TCR was decreased as the heat treatment temperature increaed. However, $RuO_2$ did not reacted with the glass frits containing ZnO nor CdO, and the resulting showed very high sheet resistivities.

• The Journal of the Petrological Society of Korea
• /
• v.12 no.3
• /
• pp.135-153
• /
• 2003

In order to understand its origin and petrogenesis, petrochemical studies of major, trace elements, REE, and stable isotopes of oxygen and carbon from the Hongcheon Fe-REE deposits have been investigated. The Hongcheon Fe-REE deposit intruding into Precambrian metasedimentary rocks consists of magnetite, various carbonates such as ankerite, siderite, magnesite and strontianite, monazite, aegirine-augite, Na-amphibole, and sulfides. Compared with major elements abundances of typical ferro-carbonatites, the Hongcheon Fe-REE deposit is enriched in FeO and depleted in CaO with increasing of $SiO_2$, where $TiO_2$and $A1_2O_3$increased and CaO, FeO, MgO and $P_2O_5$ are slightly decreased, but those are rather scattered and their trends are somewhat ambiguous. V Ni, U and Rb slightly increasing with of $SiO_2$increase and scattering or no trends of other detected elements. Nb, Zr and Zn are depleted then the abundances of typical ferro-carbonatites (Woolley and Kempe, 1989). In rare earth elements a large enrichment of total REE (maximum 14.8 wt%) and LREE relative to chondrites and HREE depleted more then the values of ferro-carbontites therefore La/Lu ratios shows large abundances (max. 16,197). The results of stable isotopes of O and C from minerals of ankerite and strontianite and whole rocks represent studied rocks are from igneous carbonatitic melts. Although petrochemical characteristics of the Hongcheon Fe-REE deposits are somewhat different from normal ferro-carbonatites from the world, this discrepancy suggests another conclusion that petrochemical characteristic of the studied Fe-REE mineralized rocks are similar to those of phoscorites from Kovdor, Russia and Sokli, Finland showing the same petrochemical compositions described above.