• Korean Journal of Materials Research
• /
• 제13권7호
• /
• pp.460-464
• /
• 2003

Ni and Ti films were deposited by the thermal evaporator, and then annealed in the N$_2$ ambient at 300-80$0^{\circ}C$ in a RTA(rapid thermal annealing) system. Four point probe, AEM, FESEM, AES, and XPS were used to study the effects of Ti-capping layers on the thermal stability of NiSi thin films. The Ti-capped NiSi was stable up to $700^{\circ}C$ for 100 sec. RTA, while the uncapped NiSi layers showed high sheet resistance after $600^{\circ}C$. These results were due to that the Ni in-diffusion and Si out-diffusion were retarded by the capping layer, resulting in the suppression of the formation of NiSi$_2$and Si grains at the surface.

• Korean Journal of Materials Research
• /
• 제15권1호
• /
• pp.66-72
• /
• 2005

Surface modification of the silicon-coated graphite was carried out at $200^{\circ}C\~800^{\circ}C$ under hydrogen atmosphere. The silicon-coated graphites were prepared by fluidized-bed spray coating method. The components of silicon films prepared on the graphite consist of SiO, $SiO_x\;(1. The components of silicon films at $200^{\circ}C$ of heat treatment brought on the higher fraction of SiO and $SiO_x$ than that of $SiO_2$. However, inactive $SiO_2$ fraction increases with increase of the heat treatment temperature. The high content of SiO and $SiO_x$ in the silicon film on graphite leads to the higher discharge capacity in our experimental range.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• 제26권5호
• /
• pp.397-400
• /
• 2013

Off-axis magnetron sputtering was used for the crystallized ITO thin films deposition at various temperatures from 25 to $120^{\circ}C$. The ITO thin films were crystallized at $50^{\circ}C$ for Si (001) substrates and at $75^{\circ}C$ for PET substrate. The ITO thin films grown onto PET substrate at $120^{\circ}C$ were crystallized with a (222) preferred orientation. The 160-nm thick ITO films showed a resistivity of about $7{\times}10^{-4}{\Omega}{\cdot}cm$ and a transmittance of about 84% at a wavelength of 550 nm. Off-axis sputtering can be applied for low temperature crystallization of the ITO films.

• Journal of the Microelectronics and Packaging Society
• /
• 제28권3호
• /
• pp.33-38
• /
• 2021

Recently, rollable and foldable displays are attracting great attention in the flexible display market due to their excellent form factor. To predict and prevent the mechanical failure of the display panels, it is essential to accurately understand the mechanical properties of brittle SiN_x thin films, which have been used as an insulating film in flexible displays. In this study, tensile properties of the ~130 nm- and ~320 nm-thick SiN_x thin films were successfully measured by coating a ~190 nm-thick organic nano-support-layer (PMMA, PS, P3HT) on the fragile SiN_x thin films and stretching the films as a bilayer state. Young's modulus values of the ~130 nm and ~320 nm SiN_x thin films fabricated through the controlled chamber pressure and deposition power (A: 1250 mTorr, 450 W/B: 1000 mTorr, 600 W/C: 750 mTorr, 700 W) were calculated as A: 76.6±3.5, B: 85.8±4.6, C: 117.4±6.5 GPa and A: 100.1±12.9, B: 117.9±9.7, C: 159.6 GPa, respectively. As a result, Young's modulus of ~320 nm SiN_x thin films fabricated through the same deposition condition increased compared to the ~130 nm SiN_x thin films. The tensile testing method using the organic nano-support-layer was effective in the precise measurement of the mechanical properties of the brittle thin films. The method developed in this study can contribute to the robust design of the rollable and foldable displays by enabling quantitative measurement of mechanical properties of fragile thin films for flexible displays.

• Journal of the Korean Ceramic Society
• /
• 제52권6호
• /
• pp.441-448
• /
• 2015

Silicon carbide (SiC) coatings for tri-isotropic (TRISO) nuclear fuel particles were fabricated using a chemical vapor deposition (CVD) process onto graphite. A micro-tensile-testing system was developed for the mechanical characterization of SiC coatings at high temperatures. The fracture strength of the SiC coatings was characterized by the developed micro-tensile test in the range of $25^{\circ}C$ to $1000^{\circ}C$. Two types of CVD-SiC films were prepared for the micro-tensile test. SiC-A exhibited a large grain size (0.4 ~ 0.6 m) and the [111] preferred orientation, while SiC-B had a small grain size (0.2 ~ 0.3 mm) and the [220] preferred orientation. Free silicon (Si) was co-deposited onto SiC-B, and stacking faults also existed in the SiC-B structure. The fracture strengths of the CVD-SiC coatings, as measured by the high-temperature micro-tensile test, decreased with the testing temperature. The high-temperature fracture strengths of CVD-SiC coatings were related to the microstructure and defects of the CVD-SiC coatings.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2005년도 춘계학술대회
• /
• pp.113-116
• /
• 2005

In this paper, silicon thin-film solar cells(Si- TFSC) and a-Si/c-Si heterojunction solar cells(HJ-cell) are investigated. The Si-TFSC was prepared on glass substrate by depositing $1-3{\mu}m$ thin-film silicons by glow discharge method. The $a-Si:H/{\mu}c-Si:H$ tandem solar cells on textured ZnO:A1 TCO (transparent conducting oxide) showed improved Jsc in top and bottom cells than that on $SnO_2:F$ TCO. This enhancement of jsc resulted from improved light trapping effect by front textured ZnO:A1. The a-Si/c-Si HJ-cells with simple structure without high efficiency features are suffering from low Voc and Jsc. The improvement of front nip and back interface properties by adopting high quality silicon-films at low temperature should be done both for increasing device performances and production cost.

• Journal of the Korean Ceramic Society
• /
• 제40권1호
• /
• pp.69-76
• /
• 2003

For lithium secondary microbattery anode, the tin oxide thin films with Si addition (0, 2, 6, 10, 20 ㏖%) were prepared with R.F. magnetron sputtering at substrate temperature of 30$0^{\circ}C$ and Ar:O$_2$=7:3 atmosphere. As Si addition amount increased, Si-O bonding density increased and Sn-O bonding density decreased. The addition of optimum Si amount led the decrease of Sn oxidation state so that the irreversible capacity reduced and cycle characteristic enhanced during charge-discharge test. SnO$_2$films with 6 ㏖% Si had the highest reversible capacity of 700 mAh/g after 100 cycles.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2002년도 하계학술대회 논문집 Vol.3 No.2
• /
• pp.1057-1059
• /
• 2002

ZnO-Si-ZnO multi-layer thin films have been deposited by pulsed laser deposition (PLD). And then, the films have been annealed at $300^{\circ}C$ in oxygen ambient pressure. Electrical properties of the films were improved slightly than ZnO thin film without Si layer. Also, the optical and structural properties changed by Si layer in ZnO thin film. The optical and structural properties of Si-doped ZnO thin films were characterized by PL(Photoluminescence) and XRD(X-ray diffraction method) respectively. Electrical properties were measured by van der Pauw Hall measurements.

• Journal of the Korean Vacuum Society
• /
• 제12권4호
• /
• pp.263-268
• /
• 2003

Precise thickness control and excellent properties of silicon nitride thin films are essential for the next-generation semiconductor and display devices. In this study, silicon nitride thin films were deposited by batch-type atomic layer deposition (ALD) method using $SiC1_4$ and $NH_3$ as the precursors at temperatures ranging from 500 to $600^{\circ}C$. Thin film deposition using a batch-type ALD reactor was a layer-by-layer atomic growth by self-limiting surface reactions, and the thickness of the deposited film can be controlled by the number of deposition cycles. The silicon nitride thin films deposited by ALD method exhibited composition, refractive index and wet etch rate similar with those of the thin films deposited by low-pressure chemical vapor deposition method at $760^{\circ}C$. The addition of pyridine mixed with precursors increased deposition rate by 50%, however, the films deposited with pyridine was readily oxidized owing to its unstable structure, which is unsuitable for the application to semiconductor or display devices.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 한국전기전자재료학회 2008년도 추계학술대회 논문집 Vol.21
• /
• pp.251-251
• /
• 2008

In this work, appropriate corrugated structure is suggested to increase resonant frequency of resonators. Micro beam resonators based on polycrystalline 3C-SiC films which have a two-side corrugation along the length of beams were simulated by finite element method and compared to a same - size flat rectangular. With the dimension of $36\times12\times0.5{\mu}m^3$, the flat cantilever has resonant frequency of 746 kHz. Meanwhile, with this size only corrugation width of $6{\mu}m$ and depth of $0.4{\mu}m$, the corrugated cantilever reaches the resonant frequency at 1.252 MHz, and is 68% larger than that of flat type.