• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2009.11a
• /
• pp.185-185
• /
• 2009

The aligned liquid crystals (LCs) display on SiNx thin films using ion-beam (IB) irradiation was studied with controllability ofpretilt angle depending on incident energies of the IB. Plasma-enhanced chemical vapor deposition (PECVD) was used to orient the LCs on SiNx alignment films. The LCs alignment property for the SiNx thin films were observed to verify the practical application potential (figure1). A good LCs alignment of vertical alignment LCs cells on SiNx thin film surfaces irradiated with incident IB energy of 1800eV was achieved. Also, a good LC alignment by the IB irradiation on the SiNx thin film surface was observed at an annealing temperature of $180^{\circ}C$. However, the alignment defects of the nematic liquid crystal was observed at an annealing temperature above $230^{\circ}C$. The atomic force microscopy (AFM) images of LCs on SiNx thin film surfaces irradiated with IB energy was used for the surface analysis.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.11
• /
• pp.1699-1705
• /
• 1989

Nitridation of about 300\ulcornerSiO2 filmss thermally grown on Si was performed in NH3 plasm ambient (0.2-2 torr) at 900\ulcornerC-1100\ulcorner for 15-20 minutes. The peoperties of those films have been investigated by analyzing the AES and the SIMS data, and the results of the I-V and the C-V measurements. At the plasma ambient of less than 1.5 torr pressure, etching of the films have been shown. Above the 1.5 torr pressure, however, SiO2 films were nitrided as SiIxNy. Plasma thermal nitridation of SiO2 by addition of small amount (6%) of CF4 to the NH3 showed higher pile-up N concentration in the surface region of SiOxNy film. The higher the nitridation temperature is and the longer the nitridation time is the larger the dielectric constant is. The plasma thermal nitridation of silicon dioxide on silicon causes the flat-band voltage shift based on the formation of the positive charge. The conduction mechanism for SiOxNy films could be elucidated by Fowler-Nordheim tnneling model. By SIMS analysis, surface of the film nitrided in plasma process has less contamination than that of the film nitrided in open-tube process.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.151-154
• /
• 2003

AlN/Al/SiO$_2$/Si thin films for application to FBAR(Film Bulk Acoustic Resonator) devices were prepared by FTS(Facing Targets sputtering system) apparatus which provides a stable discharge at low gas pressures and can deposit high quality thin films because of the substrate located apart from the plasma. The AlN thin films were deposited on a $SiO_2(1{\mu}m)/Si(100)$ substrate using an Al bottom electrode. The process parameters were fixed such as sputering power of 200W, working pressures of 1mTorr and AlN thin film thickness of 800nm, respectively and crytallographic characteristics of AlN thin films were investigated as a function of $N_2$ gas flow rate$[N_2/(N_2+Ar)]$. Thickness of AlN thin films were measured by $\alpha$-step, the crystallographic characteristics and c-axis preferred orientation were evaluated by XRD.

• Journal of the Korean Vacuum Society
• /
• v.19 no.3
• /
• pp.230-235
• /
• 2010

In this paper, we controlled the deposition rate and reflective index with process conditions that are TCP power, gas flow ratio and bias for optical properties of $SiO_2$ thin film using TCP-CVD equipment. We obtained a excellent $SiO_2$ thin film which has a excellent uniformity (<1 [%]), deposition rate (0.28 [${\mu}m$/ min]) and reflective index (1.4610-1.4621) within 4" wafer with process conditions ($SiH_4:O_2$=50 : 100 [sccm], TCP power 1 [kW], bias 200 [W]) at [$300^{\circ}C$].

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.292-292
• /
• 2011

TFT (Thin Film Transistor)에서 공정을 단순화 시키고, 가격을 하락시키기 위해서는 Poly-Si을 대체할 물질이 필요하다. 이 연구에서는 Chalcogenide Material의 하나인 GeTe 박막을 이용하여 TFT Channel으로 사용 가능한 물질인지 알아보기 위하여 Post-Annealing을 한 뒤, 상 변화에 따른 박막의 저항 변화, Carrier Concentration (cm-3)과 Mobility (cm2V-1s-1)의 변화를 알아보았다. Sputtering을 이용하여 증착한 GeTe 100 nm Thin Film 위에 Sputtering을 이용하여 SiO2 5 nm를 Capping Layer로 증착한 후, Post-Annealing을 200$^{\circ}C$, 300$^{\circ}C$, 400$^{\circ}C$, 500$^{\circ}C$로 온도를 변화 시키며 진행하였고, 이로 인하여 GeTe Thin Film에 외부의 영향을 최소화 하였다. 먼저 GeTe Thin Film의 Sheet Resistance를 측정한 결과는 300$^{\circ}C$ 까지 낮은 Sheet Resistance의 거동을 보이며 반면, 400$^{\circ}C$ 이상이 되면 높은 Sheet Resistance의 거동을 보인다. Hall Measurement를 통해, Carrier Concentration과 Mobility를 알아보았다. Carrier Concentration은 온도가 증가하면 1E+19에서 1E+21 까지 증가하며, Mobility는 감소하는 경향을 보인다. 500$^{\circ}C$ Post-Annealed GeTe Thin Film에서는 Resistivity가 상당히 높아 4 Point Probe (Range : 1 mohm/sq~2 Mohm/sq)로 측정이 불가능하다. XRD로 GeTe Thin Film을 분석한 결과 as-grown, 200$^{\circ}C$, 300$^{\circ}C$에서는 Cubic의 결정 구조를 보이며, Sheet Resistance가 급격히 증가한 400$^{\circ}C$, 500$^{\circ}C$에서는 Rhombohedral의 결정구조를 보인다. GeTe Thin Film은 400$^{\circ}C$ 이상의 Post-Annealing 온도에서 cubic 구조에서 Rhombohedral 구조로 상 변화가 일어난다. 위 결과를 통해, 결정 구조의 변화가 GeTe Thin Film의 저항, Carrier Concentration과 Mobility에 밀접한 영향이 미치는 것을 확인하였다.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.27 no.5
• /
• pp.729-736
• /
• 1990

Oxide (RTO), nitrided-oxide(NO), and reoxidized-nitrided-oxide(ONO) films were formed by sequential rapid thermal processing. The film composition was investigated by Auger electron spectroscopy(AES). The Si/SiO2 interface and SiO2 surface are nitrided more preferentially than SiO2 bulk. When the NO is reoxidized, [N](atomic concentration of N) in the NO film decreased` especially, the decrease of [N] at the surface is considerable. The weaker the nitridation condition is, the larger the increase of thickness is as the reoxidation proceeds. The elelctrical characteristics of RTO, NO, and ONO films were evaluated by 1-V, high frequency (1 MHz) C-V, and high frequency C-V after constant current stress. The ONO film-which has 8 nm thick initial oxide, nitrided in NH3 at 950\ulcorner for 60 s, reoxidized in O2 at 1100\ulcorner for 60 s-shows good electrical characteristics such as higher electrical breakdown voltage and less variation of flat band voltage under high electric field than RTO, and NO films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2001.11b
• /
• pp.77-80
• /
• 2001

Crystallographic and magnetic characteristics of CoCr-based magnetic thin film for perpendicular magnetic recording media were influenced on preparing conditions. In these, there is that substrate temperature was parameter that increases perpendicular coercivity of CoCrTa magnetic layer using recording layer. While preparation of CoCr-based doublelayer, by optimizing substrate temperature, we expect to increase perpendicular anisotropy of CoCr magnetic layer and prepare ferromagnetic recording layer with a good quality by epitaxial growth. CoCrTa/Si doublelayer showed a good dispersion angle of c-axis orientation $\Delta\theta_{50}$ caused by inserting amorphous Si underlayer which prepared at underlayer substrate temperature 250C. Perpendicular coercivity was constant, in-plane coercivity was controlled a low value about 200Oe. This result implied that Si underlayer could restrain growth of initial layer of CoCrTa thin film, which showed bad magnetic properties effectively without participating magnetization patterns of magnetic layer. In case of CoCrTa/Si that prepared with ultra thin underlayer, crystalline orientation of CoCrTa was improved rather underlayer thickness 1nm, it was expected that amorphous Si layer played a important role in not only underlayer but also seed layer.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.11a
• /
• pp.267-270
• /
• 2003

We have studied the interfacial diffusion phenomena and the role of ${\alpha}-Al_2O_3$ buffer layer as a diffusion barrier in the $Ba-ferrite/SiO_2$ magnetic thin films for high-density recording media. In the interface of amorphous Ba-ferrite ($1900-{\AA}-thick)/SiO_2$ thin film during annealing, the interfacial diffusion started to occur at ${\sim}700^{\circ}C$. As the annealing temperature increased up to $800^{\circ}C$, the interfacial diffusion abruptly proceeded resulting in the high interface roughness and the deterioration of the magnetic properties. In order to control the interfacial diffusion at the high temperature, we introduced ${\alpha}-Al_2O_3$ buffer layer ($110-{\AA}-thick$) in the interface of $Ba-ferrite/SiO_2$ thin film. During the annealing of $Ba-ferrite/{\alpha}-Al_2O_3/SiO_2$ thin film even at ${\sim}800^{\circ}C$, the interface was very smooth. The smooth interface of the film was also clearly shown by the cross-sectional FESEM. The magnetic properties, such as saturation magnetization 3nd intrinsic coercivity, were also enhanced, due to the inhibition of interfacial diffusion by the ${\alpha}-Al_2O_3$ buffer layer. Our study suggests that the ${\alpha}-Al_2O_3$ buffer layer act as a useful interfacial diffusion barrier in the $Ba-ferrite/SiO_2$ thin films.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2002.07a
• /
• pp.194-197
• /
• 2002

Applying dual layer insulator on plastic substrates improved electrical characteristics of organic thin film transistor(TFT). A high-quality silicon dioxide(SiO$_2$) suitable for a insulator was deposited on plastic substrates by e-beam evaporation at 110$^{\circ}C$. The insulator film which was treated by N$_2$ annealing at 150$^{\circ}C$ showed excellent I-V, C-V characteristics. The dual layer insulator structure of polyimide-SiO$_2$ improved the roughness of SiO$_2$ surface and showed very low leakage current. In addition, the flat band voltage has been reduced from -2.5V to about 0.5V.

• JSTS:Journal of Semiconductor Technology and Science
• /
• v.5 no.3
• /
• pp.182-186
• /
• 2005

In this work, thermal evaporation system was employed to deposit thin films of SiC on glass substrates in order to determine the parameters of them. Measurements included transmission, absorption, Seebak effect, resistivity and conductivity, absorption coefficient, type of energy band-gap, extinction coefficient as functions of photon energy and the effect of increasing film thickness on transmittance. Results explained that SiC thin film is an n-type semiconductor of indirect energy band-gap of ${\sim}3eV$, cut-off wavelength of 448nm, absorption coefficient of $3.4395{\times}10^{4}cm^{-1}$ and extinction coefficient of 0.154. The experimental measured values are in good agreement with the typical values of SiC thin films prepared by other advanced deposition techniques.