• 수산해양교육연구
• /
• 제6권1호
• /
• pp.58-76
• /
• 1994

Heat transfer and pressure drop measurements are made on low integral-fin tubes in turbulent water flow condition. The integral-fin tubes investigated in this paper are nominally 19mm in diameter. Eight tubes have been used with trapezoidally shaped integral-fins having fin density from 748 to 1654 fpm and 10, 30 grooves. Plain tube having same diameter as finned tube is also tested for comparison. Experiments are carried out using R-11 as working fluid. The refrigerant condensates at a saturation state of $30^{\circ}C$ on the outside tube surface cooled by coolant. The amount of noncondensable gases present in the test loop is reduced to a negligible value by repeated purging. For a given heat input to the boiler and given cooling water flow rate, all test data are taken on steady state. The heat transfer loop is used for testing single long tubes and cooling water is pumped from a storage tank through filters and flowmeters to the horizontal test section where it is heated by steam condensing on the outside of the tube. The pressure drop across the test section is measured by means of pressure gauge and manometer. Each tube tested is cleaned with sodium dichromate pickling solution and well rinsed with water prior to installation in the test section. The results obtained in this study is as follows : 1. Based on inside diameter and nominal inside area, heat transfer of finned tube is enhanced up to 4 times as that of a plain tube at constant Reynolds number and up to 2 times at constant pumping power. 2. Friction factors are up to 1.6~2.1 times those of plain tube. 3. At a given Reynolds number, Nusselt number decrease with increasing pitch to diameter. 4. The constant pumping power ratio for low integral-fin tubes increase directly with the effective area to the nominal area ratio, and with the effective area diameter ratio.

• 한국전자파학회논문지
• /
• 제18권8호
• /
• pp.954-963
• /
• 2007

RFID 기술이 다양한 분야에 적용됨에 따라 각 분야의 특성에 맞게 RFID 리더에 요구되는 기능들도 다양해지고 있다. 그러나 현재 구현된 8051 프로세서를 기반으로 한 시스템은 프로세서의 처리 용량의 한계 및 메모리 크기의 제한 등으로 인하여 다양한 요구 조건들을 충족시키기에 부족하다. 본 논문에서는 다양한 요구 조건들을 충족시키기 위해서 임베디드 시스템에서 많이 사용되고 있는 ARM920T 기반의 프로세서를 이용하여 EPC Class-1 Generation-2 규격을 만족하는 UHF 대역의 RFID 시스템을 설계하였다.

• 전기학회논문지
• /
• 제62권12호
• /
• pp.1678-1687
• /
• 2013

This paper describes a prototype of 3-phase 3.3kV/220V 6kVA modular semiconductor transformer developed in the lab for feasibility study. The developed prototype is composed of three single-phase units coupled in Y-connection. Each single-phase unit with a rating of 1.9kV/127V 2kVA consists of a high-voltage high-frequency resonant AC-DC converter, a low-voltage hybrid-switching DC-DC converter, and a low-voltage hybrid-switching DC-AC converter. Also each single-phase unit has two DSP controllers to control converter operation and to acquire monitoring data. Monitoring system was developed based on LabView by using CAN communication link between the DSP controller and PC. Through various experimental analyses it was verified that the prototype operates with proper performance under normal and sag condition. The system efficiency can be improved by adopting optimal design and replacing the IGBT switch with the SiC MOSFET switch. The developed prototype confirms a possibility to build a commercial high-voltage high-power semiconductor transformer by increasing the number of series-connected converter modules in high-voltage side and improving the performance of switching element.

• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2011년도 춘계학술대회 논문집
• /
• pp.618-626
• /
• 2011

Recent development of related technologies and efficient utilization of the entire country for the purpose of railway construction, and plans are being accelerated. the railway noise has been improved by increasing the high speed railway station, and accelerating the existing trains. Nord2000 which is an overseas noise prediction equation could not be applied directly to the domestic railway vehicles. So the specific vehicles in the Nordic countries which is a similar specification to domestic trains should be selected. Nord2000's accuracy was compared to Schall03, CRN's. Prediction of Ground impedance and Roughness class were carried out at different. In this paper, the result of selected vehicles for Nord2000 was as follows. S-1aX2 was for express trains, N-$^*2c$-3b was for Mugunghwa, S-Pass/wood was for Saemaul, N-4a was for freight trains, N-3a was for subway, the calculation time for Nord2000 took longer than others, in addition, Ground absorption was indispensable to calculate a noise map for Nord2000. As a result, CRN's prediction noise levels at Wonju-si was closest to the measurements. However, the predicted noise levels of Nord2000 was the most accurate.

• 대한치과기공학회지
• /
• 제40권1호
• /
• pp.9-15
• /
• 2018

Purpose: The purpose of this study is to investigate the effect of lithium disilicate glass ceramic polishing on the strength of the final prosthesis. Methods: Fourteen lithium disilicate glass ceramic specimens were prepared. These were randomly divided into two groups of seven(LPG: low polishing group, HPG: high polishing group). In LPG, SiC paper was sequentially polished using 300, 600, 800, 1000 grit, and the specifications of the test piece were adjusted. HPG was sequentially polished using 300, 600, 800, 1000, 1200, 1500, and 2000 grit. Two groups of specimens are executed 3- point bending test. Using the statistical program SPSS 22.0, the average values of the strengths of the two groups were compared in the Mann-Whiteney test. The significance level was set at 0.05. Results: The mean strength value of HPG was measured at $307.14{\pm}23.28MPa$ significantly higher than LPG(p<0.001). Conclusion : The final polishing of the prosthesis is aesthetically important but has proven to play an important role in the flexural strength, early fracture, and prolongation of the prosthesis.

• Current Photovoltaic Research
• /
• 제1권1호
• /
• pp.17-26
• /
• 2013

In contrast to conventional crystalline cells, back-contact solar cells feature high efficiencies, simpler module assembly, and better aesthetics. The highest commercialized cell and module efficiency was recorded by n-type back-contact solar cells. However, the mainstream PV industry uses a p-type substrate instead of n-type due to the high costs and complexity of the manufacturing processes in the case of the latter. P-type back-contact solar cells such as metal wrap-through and emitter wrap-through, which are inexpensive and compatible with the current PV industry, have consequently been developed. In this paper the characteristics of EWT (emitter wrap-through) solar cells and their status and prospects for development are discussed.

• 한국통신학회논문지
• /
• 제32권5C호
• /
• pp.469-477
• /
• 2007

소스 코딩을 통해 얻어지는 대다수의 멀티미디어 데이터 정보는 여러 등급의 다른 비트에러민감도를 가지고 있다. 그러므로 효율적인 시스템 구현을 위해서는 데이터 고유의 비트에러민감도에 따라 서로 다른 수준의 에러 방지를 제공해야 한다. 이 논문에서는 다중안테나 (multiple-in multiple-out : MIMO) 기반의 OFDM시스템에서 효과적인 멀티미디어 정보를 전송하기 위한 차등 에러 방지 기법(Unequal error protection : UEP)을 제안한다. 차등의 에러 방지를 제공하는 시공간 코딩 기법을 설명하고 그 성능을 평가한다. MIMO 기법과 BICM (Bit-interleaved coded modulations) 기술은 보통 RCPC (Rate compatible punctured convolutional codes) 기법과 연계되어 구동된다. 이때 다중안테나 채널 이퀄라이저와 채널코딩 사이에 터보디코딩 기법을 적용하여 최상의 성능을 얻을 수 있는데 기존의 시스템에서는 동일한 에러방지기법(Equal Error Protection : EEP)을 사용하고 있다. 이 논문에서는 이런 시스템 구조에서 보통 사용되는 동일 에러 방지 기법(EEP)와 비교하여 차등 에러방지 기법(UEP)를 사용함으로써 얻을 수 있는 이득을 사용되는 전송파워와 채널밴드 측면에서 설명한다. 특히 제안된 알고리즘을 둘 또는 세 개의 전송 안테나와 두 개의 수신안테나를 갖는 다중안테나 시스템에 적용하고 8PSK 신호를 이용하여 플랫 페이딩 채널에서 성능을 평가하였다.

• JSTS:Journal of Semiconductor Technology and Science
• /
• 제11권2호
• /
• pp.121-129
• /
• 2011

It is progressing as new advents and remarkable developments of mobile device every year. On the upper line reason, NAND FLASH large density memory demands which can be stored into portable devices have been dramatically increasing. Therefore, the cell size of the NAND Flash memory has been scaled down by merely 50% and has been doubling density each per year. [1] However, side effects have arisen the cell distribution and reliability characteristics related to coupling interference, channel disturbance, floating gate electron retention, write-erase cycling owing to shrinking around 20nm technology. Also, FLASH controller to manage shrink effect leads to speed and current issues. In this paper, It will be introduced to solve cycling, retention and fail bit problems of sub-deep micron shrink such as Virtual negative read used in moving read, randomization. The characteristics of retention, cycling and program performance have 3 K per 1 year and 12.7 MB/s respectively. And device size is 179.32 $mm^2$ (16.79 mm ${\times}$ 10.68 mm) in 3 metal 26 nm CMOS.

• 한국환경과학회지
• /
• 제16권11호
• /
• pp.1225-1230
• /
• 2007

The emissions characteristics of particulate matters(PM) according to the types of wastes from industrial waste incinerator of 800 kg/hr treatment capacity were investigated. For this study, the incinerate waste are as follows; waste resin, waste wood, waste urethane, waste gunny, and waste paper. The particulate samples were collected to be emitted in stack and air pollution control(both cyclone and bag filter). In stack, the concentrations of PM were in the range of 2.61 to $26.51 mg/Sm^3$ and the major chemical species were C, Si, Cl, K, Na, Ca in all the wastes. In cyclone fly ash, the mean content of heavy metal were in the order of Fe > Zn > Pb > Cu > Mn > Cr > Ni > Cd > As > Hg and the heavy metal content of waste resin were Zn 34,197.5 mg/kg, Fe 27,587.6 mg/kg, Pb 6,055.8 mg/kg, respectively. In bag filter fly ash, the mean content of heavy metal were in the order of Zn > Pb > Fe > Cu > Mn > Cd > Cr > Ni > As > Hg and the heavy metal content of waste wood were Pb 36,405.2 mg/kg, Fe 15,762.9 mg/kg, Cu 9,989.5 mg/kg, Cd 2,230.1 mg/kg, respectively. Comparing the heavy metal content of both cyclone and bag filter, in cyclone, the Cr, Fe, Ni content were higher than in bag filter and the Cd, Cu, Hg content were lower than in bag filter.

• Restorative Dentistry and Endodontics
• /
• 제30권4호
• /
• pp.319-326
• /
• 2005

본 연구는 단일 단계 접착제의 표층과 심층 상아질에 대한 미세인장 결합강도의 차이를 평가하기 위해서 시행되었다. 발거된 상$\cdot$하악 대구치의 교합면측에 있는 표층 상아질과 심층 상아질을 각각 15개씩 노출시킨 후, 사용된 접착제에 따라 AQ군, L-Pop군, Xeno군으로 분류하여 복합레진을 축조하였다. 각 시편은 상아질과 복합레진 계면의 단면적이 $1.0mm^2$이 되도록 절단하였고, 각 군 당 20개의 시편을 사용하였다. 각 군의 미세인장 결합강도의 측정하여 다음과 같은 결과를 얻었다. 표층과 심층 상아질 모두에서 Xeno III는 다른 접착제보다 가장 높은 결합강도를 나타내었다 (p<0.05). 또한 모든 접착제는 심층 상아질에서 보다 표층 상아질에서 더 높은 결합강도를 나타내었으나 이들 간에 통계학적 인 유의성은 접착제의 종류에 따라 다르게 나타났다.