• Journal of the Korean Recycled Construction Resources Institute
• /
• v.7 no.2
• /
• pp.166-173
• /
• 2019

In this paper, the reaction properties of silica source in the accelerated curing conditions using autoclave and the fundamental properties of inorganic Micro Defect Free(MiDF) concrete using silica source are studied. Studies show that Si ions elution rate from silica source in autoclave curing is higher in amorphous source. In tap water conditions, solids which is source after autoclaved curing show a higher mass reduction in amorphous materials, which is attributed to the higher elution rate of ion. In $Ca(OH)_2$ solution conditions, amorphous materials show higher mass increase, due to increase in C-S-H minerals. From experiment for influence on the properties of MiDF concrete by using nano silica materials, the specimen with silica fume shows an increase in compressive strength and a decrease in absorption depending on replacement rate up to 5.5%, while nano silica with amorphous phase and high-fineness shows a decrease in compressive strength and decrease in the water absorption. The specimen with nano silica increases the pore below 10,000nm, but reduces pore between 10,000 and 100,000nm. The above results show that the porosity and absorption rate of MiDF concrete can be reduced by using amorphous nano-size silica. However, to reduce the pore of 50 to 10,000nm, better dispersion of nano material in the cement matrix will be necessary. We will focus on the this item in the next research.

• Journal of the Korean Recycled Construction Resources Institute
• /
• v.11 no.1
• /
• pp.89-96
• /
• 2023

In this paper, a ferrosilicon by-product was evaluated to confirm the feasibility of recycling it as supplementary cementitious material of ordinary Portland cement in concrete. Three different levels of replacement ratio (10 %, 20 % and 30 % of total binder) were applied to find which is the most beneficial to be used as a binder. Ferrosilicon concrete was initially assessed at setting time and compressive strength. Durability was evaluated by the resistance to chloride penetration test(RCPT) and alkali-silica reaction(ASR) with a comparison to silica fume concrete due to their similarity in chemical composition. The porosimetry and X-ray diffraction analysis along with energy dispersive X-ray spectroscopy give information on the microstructural characteristics of the ferrosilicon concrete. It was found that 10 % ferrosilicon concrete has higher strength while 20 %, 30 % have lower strength than OPC concrete. However, chemical resistance to chloride attack is higher when replacement is increased. Compared to silica fume, the durability of ferrosilicon might be less efficient however, it is obviously beneficial than OPC. High SiO₂ content in ferrosilicon results in producing more C-S-H gel which could make denser pore structure. Most of the risk of alkali silica reaction to silicate binders through length change tests was less than 0.2 %, and both mortar using ferrosilicon and silica fume showed better resistance to alkali silica reaction as the substitution rate increased.Reuse of industrial waste rather than producing highly refined additives might reduce environmental load during manufacture and save costs.

• Korean Journal of Environmental Agriculture
• /
• v.7 no.1
• /
• pp.34-42
• /
• 1988

To investigate the effects of paper sludge on seasonal variations of volatile lower fatty acids in paddy soil, paper sludge was applied to pots at the rate of either 300, 600, 900 or 1,200 kg/l0a which was either preadjusted at a C/N ratio of 30 : 1 or not adjusted. The decomposition rate of paper sludge, the evolution of $CO_2$, and the fractions of volatile lower fatty acids in the soil were determined. The results are summarized as follows: 1. Paper sludge was decomposed to $35{\sim}44%$, and its C/N ratio was $55{\sim}82$, respectively, at 120 days after treatment. 2. The evolution of $CO_2$, in the soil was proportional to the amount of paper sludge added. Significant positive correlations were observed the $CO_2$ evolution was compared with the decomposition rate of paper sludge, and volatile fatty acid contents in soil. 3. Acetic, propionic, butyric, i-butyric, valeric and i-valeric acids were identified in all the soils investigated. The content of the total volatile fatty acids in the soil increased with as the application of paper sludge increased. The formation of the acids was the highest at 25 days after treatment, and thereafter the contents of the acids decreased as time elapsed. 4. The volatile fatty acids in the soil inhibited the growth of paddy rice in early stages. The contents of acetic, propionic and i-valeric acids in the soil negatively, correlated with the uptake of N, $P_2O_5$, $K_2O$, CaO, MgO and $SiO_2$ in the paddy rice at 25 days after transplantation. In addition, the uptake of $P_2O_5$ and CaO in the paddy rice negatively correlated with the content of butyric acid in the soil. 5. The content of total volatile fatty acids positively correlated with the content of $Fe^{++}$ and $Mn^{++}$ in the soil at 25 days after transplantation. A significantly positive correlation was observed between $Fe^{++}$ and acetic acid contents in the soil.

• Restorative Dentistry and Endodontics
• /
• v.29 no.1
• /
• pp.13-22
• /
• 2004

본 연구는 치수강 상아질 부위 및 상아질 접착제 종류에 따른 결합 강도를 측정하고 이들 사이의 상관관계를 구명하고자 시행되었다 45개의 대구치를 포매 후, 대조군에서는 교합면 법랑질 제거 후 ＃600 SiC paper까지 순차연마하여 상아질을 노출시켰고, 실험군에서는 치수강 개방 후 1시간동안 NaOCl에 보관 후 axial wall과 pulpal floor를 노출시켰다. 노출된 상아질 면에 상아질 접착제를 적용한 후 Z-100을 충전한 다음 40초간 광중합하였다. 사용된 상아질 접착제는 Scotchbond Multi-Purpose와 Single Bond, Clearfil SE Bond였다. $37^{\circ}C$ 증류수에 24시간 보관 후, 저속 diamond saw를 이용하여 0.7mm 두께로 수직절단하고 고속 diamond point(#104)로 단면적 $1{mm}^2$가 되도록 시편을 제작하고, Universal testing machine에서 미세인장 결합강도를 측정하였다. 1. 모든 상아질 접착제의 미세인장강도는 대조군, axial wall군, pulpal floor군 순으로 감소하는 경향을 보였다. 2. 대조군에서 SM과 BB는 SE에 비해 유의성 있게 높은 결합강도를 나타내었다(p<0.05). 3. SM과 SB는 대조군에 비해 axial wall군과 pulpal floor군에서 유의성있게 낮은 결합강도를 보였으나, SE에서는 pulpal floor군만이 유의성 있게 낮은 결합강도를 보였다(p<0.05). 4. Axial wall군과 pulpal floor군에서는 상아질 접착제의 종류에 따른 유의차를 보이지 않았다. 5. 전자현미경 소견에서는 대조군에 비해 axial wall군과 pulpal floor군이 더 부드러운 접착 계면을 나타내었다. 혼성층의 두께는 결합강도의 감소와는 관련이 없었다.

• Journal of the Korean Vacuum Society
• /
• v.13 no.1
• /
• pp.34-38
• /
• 2004

Hot embossing master is indispensable for the fabrication of polymeric optical waveguides using hot embossing technology. Sidewall roughness of silicon master is directly related to optical loss of optical waveguides In this paper, a silicon master was fabricated by using a deep-RIE process. Additionally, thermal oxidation followed by oxide removal was carried out to minimize etched Si sidewall roughness. Thermal oxidation and oxide removal were performed with $H_2O_2$ atmosphere at $1050^{\circ}C$ and $NH_4$F:HF=6:l BOE, respectively, for the oxide thickness of 400$\AA$, 1000$\AA$, 3000$\AA$, 4500$\AA$, 5600$\AA$ and 6200$\AA$. The sidewall roughness was characterized by SEM and SPM-AFH measurements. We found that the roughness was improved from 12nm (RMS) to 6nm (RMS) for the scalloped sidewall and from 162nm (RMS) to 39nm (RMS) for the vertical striation sidewall, respectively.

• Journal of the Korean Data and Information Science Society
• /
• v.28 no.5
• /
• pp.1145-1152
• /
• 2017

Environmental tests are used to verify an equipment that can withstand the rigors of harsh environments. In general, military products have lots of experiences with extreme environment compared to commercial products. Therefore, the military products used in mountains require a tailoring process about temperature drop for the environmental test. The International Organization for Standardization publishes that the coefficient of temperature drop is $-6.5^{\circ}C/1000m$ from all around the world. However, there is no the criteria in the South Korea. In this paper, we calculate the coefficient of temperature drop. Also, an equation used as a tailoring process for a low temperature test of the products has been suggested.

• Proceedings of the KIEE Conference
• /
• 1991.07a
• /
• pp.753-756
• /
• 1991

This paper aimed to analyse dose sensitivity to the controllable parameters of in-door radon $(^{222}Rn)$ and its decay products(Rn-D) by applying the input-output linear system theory. Physical behaviors of $^{222}Rn$ & Rn-D were analyzed in terms of $^{222}Rn$ gas generation, -migation and - infiltration to indoor environments, and the performance output-function(i.e. mean dose equivalent to Tracho-Bronchial(TB) lung region was assessed to the following ranges of the controllable parameters; a) the ventilation rate constant $({\lambda}_v)$ : $0{\sun}500[h^{-1}]$. b) the attachment rate constant$({\lambda}_a)$ : 0-500 $[h^{-1}]$. c) deposition rate constant $({\lambda}{_{d}^{u}})$: 0-50$[h^{-1}]$. A linear input-output model was reconstructed from the original models in literatures, as follows, which was modified into the matrices consisting of 111 nodal equations. a) indoor ${222}Rn$ & Rn-D Behaviour: jacobi- Porstendorfer- Bruno model. b) lung dosimerty : Jacobi-Eisfeld model. Some of the major findings, which identify the effectiveness of this model, were as follows. a) ${\lambda}_v$ is most effective, dominant controllable parameters in dose reduction, if mechanical ventilation is applied. b) ${\lambda}_v$, depending on the air particle-concentration, reduces the dose somewhat within ${\lambda}_v$<1 $h^{-1}R range. However, the dose increases conversely, ${\lambda}_v$>1 $h^{-1}R range range. c) ${\lambda}{_{d}^{4}}$ reduces the dose linearly as ${\lambda}_v$ dose. Such dose(z-axis) sentivities are shown with three-dimensional plots whoes x,y-axes are combined 2out the 3 parameter${\lambda}_v{\lambda}_s,\;{\lambda}_d^s$.

• 한국신재생에너지학회:학술대회논문집
• /
• 2007.06a
• /
• pp.250-253
• /
• 2007

An evaporated Ti/Pd/Ag contact system is most widely used to make high-efficiency silicon solar cells, however, the system is not cost effective due to expensive materials and vacuum techniques. Commercial solar cells with screen-printed contacts formed by using Ag paste suffer from a low fill factor and a high shading loss because of high contact resistance and low aspect ratio. Low-cost Ni and Cu metal contacts have been formed by using electroless plating and electroplating techniques to replace the Ti/Pd/Ag and screen-printed Ag contacts. Ni/Cu alloy is plated on a silicon substrate by electro-deposition of the alloy from an acetate electrolyte solution, and nickel-silicide formation at the interface between the silicon and the nickel enhances stability and reduces the contact resistance. It was, therefore, found that nickel-silicide was suitable for high-efficiency solar cell applications. The Ni contact was formed on the front grid pattern by electroless plating followed by anneal ing at $380{\sim}400^{\circ}C$ for $15{\sim}30$ min at $N_{2}$ gas to allow formation of a nickel-silicide in a tube furnace or a rapid thermal processing(RTP) chamber because nickel is transformed to NiSi at $380{\sim}400^{\circ}C$. The Ni plating solution is composed of a mixture of $NiCl_{2}$ as a main nickel source. Cu was electroplated on the Ni layer by using a light induced plating method. The Cu electroplating solution was made up of a commercially available acid sulfate bath and additives to reduce the stress of the copper layer. The Ni/Cu contact was found to be well suited for high-efficiency solar cells and was successfully formed by using electroless plating and electroplating, which are more cost effective than vacuum evaporation. In this paper, we investigated low-cost Ni/Cu contact formation by electroless and electroplating for crystalline silicon solar cells.

• Transactions of the Korean hydrogen and new energy society
• /
• v.20 no.5
• /
• pp.432-438
• /
• 2009

In this paper, we synthesized LSG powder by Modified-GNP method. Lanthanum, strontium and gallium (LSG) were selected in the preparation of an oxygen-electrode (anode) for High Temperature Steam Electrolysis system (HTSE). The used amount and concentration of nitric acid were varied to find out an appropriate composition for oxygen-electrode (anode). In order to optimize the molar ratio of La and Sr, ratio of La to Sr was varied that 2:8, 5:5 and 8:2. The combined LSGs were calcined for 2 hours at $700^{\circ}C$ and were sintered in a furnace for 4 hours at $1200^{\circ}C$. The phase and crystallinity of LSG powder were determined by XRD. The surface morphology was observed through SEM photograph, and the specific surface area was investigated with BET. The thermochemical property was determined by TG/DTA. The synthesized preparation was obtained of $La_{0.8}Sr_{0.2}GaO_{3}$ formula for 3M nitric acid, which was the best perovskite phase.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.25 no.7
• /
• pp.516-520
• /
• 2012

In this paper, we have theoretically analyzed and designed a dielectric multi-layer sensor with a SPR (surface plasmon resonance) using analytical calculation and FDTD (finite difference time-domain) methods. The proposed structure is composed of periodic layer and thin metal film. It has many advantages. One of that is a high sensitivity of the SPR. Another is a high Q-factor of the characteristics in the PhC (photonic crystals) micro-cavity structure. The incident light has double resonance characteristics, because the filtered light by PhC structure, dielectric multi-layer, is met the thin metal film for SPR effect. We have also observed the change of resonance characteristics according to the variation of effective index on the metal film.