• Journal of Technologic Dentistry
• /
• v.14 no.1
• /
• pp.119-132
• /
• 1992

This paper aims to investigate the effect of B and Si upon the mechanical properties, microstructure and corrosion resistance of Co-Cr base alloy. Ten groups of alloy ingot ingot with various contents of B and Si were remelted by high frequency electrical induction furnace and cast into tensile specimen of ADA Specification No. 14 Tensile and hardness test were carried out by Amsler and Rockwell hardness tester(R-30N), respectively. The microstructures of specimen were observed by SEM. The results obtained are summarized as follows : 1. As B content is increased, tensile strength, yield strength and Rockwell hardness number(R-30N) are also increased significantly, while the elongation is decreased significantly. 2. As Si contect os increased, no significant chang in tensile strength is noticed, yield strength is slightly decreased, but Rockwell hardness number(R-30N) is moderately in creased, Elongation marks maxium value with 1% Si content while with more than 1% Si it is decreased. 3. As B content is increased corrosion resistance is decreased and is at best with 1.5% B content. Corrosion resistance is increased with the increase of Si content and the alloys with Si over 3.0% showed corrosion resistance. 4. As B content increased, precipitates are increased in number at grain boundaries. The grain size tends to become coarse with the increase of Si content. 5. Co rich-Cr alloy is present through matrix whereas at the grain boundaries Cr base precipitates are primarily formed.

• Food Science of Animal Resources
• /
• v.28 no.2
• /
• pp.138-145
• /
• 2008

This study was carried out to compare the meat quality of beef from Hanwoo supplemented with dietary Rhus verniciflua Stokes (RVS) meal, silicate (Si), and chromium-methionine (Cr-Met) during refrigerated storage. The 26 mon-aged Hanwoo steers were fed basal diets containing 4% RVS, 4% RVS+400 ppm Cr-Met, 1.4% $SiO_2$, or 0.14% $SiO_2+400 ppm$ Cr-Met for 4 mon prior to slaughter. The M. longissimus from carcasses were then stored at $4{\pm}0.2^{\circ}C$ for 7 d. The crude fat content was higher in the Si and Si+Cr-Met groups (p<0.05). The water-holding capacity (WHC) and tenderness were highest in the Si+Cr-Met group (p<0.05). With regard to fatty acids, the polyunsaturated fatty acid (PUFA) content was lower in the Si and Si+Cr-Met groups (p<0.05), and the monounsaturated fatty acid (MUFA) content was lowest in the Si+Cr-Met group (p<0.05). The TBARS and MetMb contents were decreased in the Si, Si+Cr-Met, and RVS+Cr-Met groups. Regarding meat color during storage, the Si+Cr-Met group showed the highest L, a, b, C values and total color, and those of the Si and RVS+Cr-Met groups were higher than the RVS group (p<0.05). Consequently, beef from Si-fed Hanwoo had higher fat content, color and oxidation stability, and lower PUFA content than RVS-fed beef. And beef from Si+Cr-Met-fed Hanwoo had higher WHC, tenderness and color stability, and lower MUFA content than Si-fed beef.

• Nuclear Engineering and Technology
• /
• v.33 no.4
• /
• pp.386-396
• /
• 2001

Mixtures Of AUC-UO$_2$and Gd$_2$O$_3$ Powders doped With Cr$_2$O$_3$ or Cr$_2$O$_3$-SiO$_2$ were Pressed and sintered at 1730 t in hydrogen gas witk various water-vapor contents. The density of UO$_2$- 6wt% Gd$_2$O$_3$ pellets can be increased from 91% TD to 94.5% TD in 1 vol% $H_2O$-H$_2$ gases by the addition of 0.02wt% Cr$_2$O$_3$-(0.01~0.04) wt% SiO$_2$. The magnitude of density increase is much larger in (1~3 vol%) $H_2O$-H$_2$ gases than in 0.05 vol% $H_2O$-H$_2$ gas. The densification of U0$_2$- Gd$_2$O$_3$ compact is significantly delayed in the temperature range between 1300 and 1500 t , but that of compacts with Cr$_2$O$_3$-SiO$_2$ is not. The role of Cr$_2$O$_3$ and SiO$_2$ in densification is discussed.

• Proceedings of the KSME Conference
• /
• 2007.05a
• /
• pp.262-267
• /
• 2007

In this paper, we study about wear properties for the metal matrix composites fabricated by low pressure infiltration process. Metal fiber preform reinforced aluminum alloy composite were fabricated by low pressure casting process under 0.4MPa. Infiltration condition was changed the pressure infiltration time of 1 s, 2 s and 5 s under a constant pressure of 0.4MPa. The molten alloy completely infiltrated the FeCrSi metal perform regardless of the increase in the pressure acceleration time. However, the infiltration time at the pressure acceleration time of 1s was shorter than at the pressure acceleration time of 2s or 5s. The FeCrSi/A366.0 composite was investigated the porosity. The porosity is reducing as the pressure acceleration time compared with the pressure acceleration time of 2s and 5s. The FeCrSi/A366.0 composites were investigated the wear resistance. FeCrSi/A366.0 composite at pressure acceleration time of 1s has excellent wear resistance.

• Korean Journal of Materials Research
• /
• v.14 no.11
• /
• pp.780-785
• /
• 2004

The degradation mechanism of soft magnetic properties of $Fe-Hf-N/Cr/SiO_2$ thin films reacted with a bonding glass was investigated. When $Fe-Hf-N/Cr/SiO_2$ films were annealed under $600^{\circ}C$ without the bonding glass, the compositions and the soft magnetic properties of Fe-Hf-N layers were not changed. However, after reaction with the bonding glass at $550^{\circ}C$, the soft magnetic properties of the film were degraded. At $600^{\circ}C$, the saturation magnetization of the reacted film decreased to 13.5 kG, and its coercivity increased to 4 Oe, and its effective permeability decreased to 700. It was founded that O diffused from the glass into the Fe-Hf-N layers during the reaction and generated $HfO_2$ phases. It was considered that the soft magnetic properties of the $Fe-Hf-N/Cr/SiO_2$ films reacted with the bonding glass were primarily degraded by the formation of the Fe-Hf-O-N layer of which the Fe content was below 60 $at\%$, and secondarily degraded by the Fe-Hf-O-N layer above 70 $at\%$.

• Korean Journal of Metals and Materials
• /
• v.47 no.12
• /
• pp.866-872
• /
• 2009

The effects of magnetic powder thickness on electromagnetic wave absorption characteristics in Fe-6.5Si-0.9Cr (wt%) alloy flakes/polymer composite sheets available for quasi-microwave band have been investigated. The atomized FeSiCr powders were milled by using attritor for 12, 24, and 36 h, powder thickness changed from $40{\mu}m$ to $3{\mu}m$ upon 36 h milling. The composite sheet, including thinned magnetic flakes, exhibited higher power loss in the GHz frequency range as compared with the sheets having thick flakes. Moreover, both the complex permeability and the loss factor increased with the decrease in thickness of the alloy flakes. Therefore, the enhanced power loss property of the sheets containing thin alloy flakes was attributed to the flakes of high complex permeability, especially their imaginary part. Additionally, the complex permittivity was also increased with the reduction of flake thickness, and this behavior was considered to be helpful for improvement of the electromagnetic wave absorption characteristics in the composite sheets, including thin alloy flakes.

• Transactions on Electrical and Electronic Materials
• /
• v.4 no.1
• /
• pp.15-20
• /
• 2003

NiCr alloys are prepared onto poly-Si/ $SiO_2$/Si substrates to replace Pt bottom electrode with a new one for integration of high dielectric constant materials. Alloys deposited at Ni and Cr power of 40 and 40 W showed optimum properties in the composition of N $i_{1.6}$C $r_{1.0}$. The grain size of films increases with increasing deposition temperature. The films deposited at 50$0^{\circ}C$ showed a severe agglomeration due to homogeneous nucleation. The NiCr alloys from the rms roughness and resistivity data showed a thermal stability independent of increasing annealing temperature. The 80 nm thick BST films deposited onto N $i_{1.6}$C $r_{1.0}$/poly-Si showed a dielectric constant of 280 and a dissipation factor of about 5 % at 100 kHz. The leakage current density of as-deposited BST films was about 5$\times$10$^{-7}$ A/$\textrm{cm}^2$ at an applied voltage of 1 V. The NiCr alloys are possible to replace Pt bottom electrode with new one to integrate f3r high dielectric constant materials.terials.

• Proceedings of the Korean Institute of Surface Engineering Conference
• /
• 2007.11a
• /
• pp.7-9
• /
• 2007

Thin films of CrAlSiN were deposited on SKD11 tool steel substrate using Cr and AlSi cathodes by a cathodic arc plasma deposition system. The influence of process parameters on the deposited film properties were investigated. The oxidation characteristics of the films were studied at temperatures ranging from 800 and 1000+C up to 50 h in air. The films showed superhardness and good oxidation resistance..

• Journal of Korea Foundry Society
• /
• v.5 no.3
• /
• pp.13-18
• /
• 1985

Decarburization phenomena were investigated at $800^{\circ}C$ by the $PH_2O/PH_2$ + Ar gas mixture in the case iron range which contains Si, Mn and Cr as an alloying elements. Dissociation of cementite in a matrix which contains graphitizer as Si begins at the carbon rich cementite dendrite arms. Several primary austenite $({\gamma})$ skeletons are surrounded by those nucleated graphite nodules, and that forms a limited area of nucleation region. Decarburization reactions at $800^{\circ}C$ in Fe-C, Fe-Mn-C and Fe-Cr-C alloy are followed by parabolic rate law under the gas mixture of $PH_2O/PH_2=0.01$ and the modified rate const. ${\kappa}$ were in the range of $1{\sim}6{\times}10^{-10}cm^2/s$.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2003.07a
• /
• pp.550-552
• /
• 2003

We prepared $Co_{77}Cr_{20}Ta_3$ Magnetic layer for perpendicular magnetic recording media with introduce Two-step methode and Amorphous Si Underlayer on slide glass substrate. The thickness of magnetic layer were 100nm, and Underlayer were varied from 5 to 100 nm. The multi layer Properties of crystal structure were examined with XRD. Prepared thin films showed improvement of dispersion angle of c-axis orientation ${\Delta}{\theta}_{50}$ caused by inserting Buffer-layer and amorphous Si underlayer.