• Journal of the Korean Wood Science and Technology
• /
• 제22권2호
• /
• pp.37-45
• /
• 1994

The possibility of reusing the paper sludge as a raw material of composition board mixed with cement was investigated. For the measurement of physical and mechanical properties, wood coment board and sludge combinend cement boards were fabricated with the three weigh ratios of paper sludge 10 % (SI), 20 % (S II) and 30 % (S III) to cement weight. For adding the cement hardning, $CaCl_2$ was also added to each mixed paste with the ratio of 1 %, 3 % and 5 % to cement weight, respectively. Crystal formation in paper sludge-, wood-cement composites was observed by scanning electron microscope. The results were summarized as follows. 1. Density and partial compressive strength of each specimens were relatively high in the order of sludge I, sludge II, Korean pine, Italian poplar and sludge III, sludge I, Korean pine, sludge II, Italian poplar and sludge III. 2. The mechanical properties of sludge-cement boards (S I and II) were higher than that of wood-cement boards prepared with Korean pine and Italian poplar. But the mechanical properties of wood-cement boards were improved by the adding of $CaCl_2$. 3. Water absorption and thickness swelling were increased with increase of sludge content to cement weight. 4. In SEM observation, sludge-cement composites showed sufficiently formed crystals but wood-cement composites showed poorly formed crystals.

• 한국분말재료학회지
• /
• 제28권5호
• /
• pp.423-428
• /
• 2021

Here, we report the development of a new and low-cost core-shell structure for lithium-ion battery anodes using silicon waste sludge and the Ti-ion complex. X-ray diffraction (XRD) confirmed the raw waste silicon sludge powder to be pure silicon without other metal impurities and the particle size distribution is measured to be from 200 nm to 3 ㎛ by dynamic light scattering (DLS). As a result of pulverization by a planetary mill, the size of the single crystal according to the Scherrer formula is calculated to be 12.1 nm, but the average particle size of the agglomerate is measured to be 123.6 nm. A Si/TiO₂ core-shell structure is formed using simple Ti complex ions, and the ratio of TiO₂ peaks increased with an increase in the amount of Ti ions. Transmission electron microscopy (TEM) observations revealed that TiO₂ coating on Si nanoparticles results in a Si-TiO₂ core-shell structure. This result is expected to improve the stability and cycle of lithium-ion batteries as anodes.

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 춘계총회,특별강연,심포지움,연구발표회
• /
• pp.101.1-101.1
• /
• 2000

• 한국세라믹학회:학술대회논문집
• /
• 한국세라믹학회 2000년도 추계총회,초청강연,특별강연,연구발표회
• /
• pp.205.2-205
• /
• 2000

• 한국방사성폐기물학회:학술대회논문집
• /
• 한국방사성폐기물학회 2005년도 춘계 학술대회
• /
• pp.129-136
• /
• 2005

원자력 발전소의 증기발생기 슬러지 중에서는 이온교환수지가 발견되어서는 안 된다. 증기발생기 슬러지 시료 중에서 발견되어 이온교환수지 입자로 의심되는 구형 입자들의 특성을 측정하였다. 미세조작기술을 이용하여 광학현미경으로 입자 크기 분포를, EPMA로 구형입자의 성분을, 그리고 IR 분광 스펙트럼 비교에 의하여 이온교환수지 여부를 조사하였다. 슬러지의 입자 크기는 1내지 200 ${\mu}m$이었으나 구형입자는 40-500 ${\mu}m$이었으며, 슬러지의 주요 불순원소가 Si, Al, Mn, Cr, Ni, Zn, 그리고 Ti이었으나 구형입자는 Si, Cu, Zn 이었다. 주성분은 두 경우 모두 철이었으며, IR 분광스펙트럼을 S/G 시스템에서 사용하는 이온교환수지의 경우와 비교했을 때 서로 다른 결과를 보였다. 이 결과들은 것은 증기발생기 슬러지 시료 중에서 발견된 구형 입자가 이온교환수지는 아니며 일반적인 슬러지가 생성되는 과정에서 작은 슬러지 입자들이 크게 뭉쳐서 생성된 것임을 나타내고 있다.

• 한국융합학회논문지
• /
• 제8권2호
• /
• pp.157-162
• /
• 2017

제지슬러지 소각재, 용광로 슬래그 미세분말 생석회, 무수석고 및 프라이애쉬 등을 혼합하여 무기계고화재를 제조하였다. 슬러지 처리용으로 개발된 고화재의 주성분은 SiO, $Al_2O_3$, $TiO_2$, $Fe_2O_3$, $Mn_2O_3$, CaO, MgO, $Na_2O$, $K_2O$, $P_2O$, $SO_3$이었다. 시멘트와 달리, 개발된 고화재에는 발암물질로 알려진 $Cr^{6+}$가 함유되지 않았다. 중금속 및 기름 오염토를 고화재와 혼합한 후 7일간 양생하여 빗물용출실험을 시행한 결과 중금속이 미미하였다. 하수슬러지 케이크 및 음식물쓰레기와 고화재를 각각 혼합하여 7일 양생 후 토양성분실험을 한 결과 중금속 함량이 환경기준치 이하로 나타났다. 슬러지, 고화재 및 첨가제 혼합시료를 비이커에 혼합한 후 암모니아 농도를 측정한 결과 3일 후 0이 되었다.

• Architectural research
• /
• 제12권1호
• /
• pp.49-55
• /
• 2010

Stone powder sludge is a by-product of the manufacturing process of crushed sand. Most of it is dumped with soil in landfills, and the disposal of stone powder sludge causes a major environmental problem. This paper investigates the applicability of stone powder sludge in fly ashbased geopolymer. For this, stone powder sludge was used to replace fly ash at a replacement ratio of 50% and 100% by weight. The compressive strength of the samples was measured and scanning electron microscopy/ energy dispersive spectroscopy (SEM/EDS) analysis and X-ray diffraction (XRD) were performed. The test results indicated that the optimum level of the alkali activator ratio ($Na_2SiO_3$/NaOH) for fly ash-based geopolymer using stone powder sludge was 1.5. The strength development is closely related to the NaOH solution concentration. In addition, the compressive strength of the sample cured at $25^{\circ}C$ was significantly improved between 7 days and 28 days, even though the strength of the sample showed the lowest value at 7 days. Microscopy results indicated that a higher proportion of unreacted fly ash spheres remained in the sample with 5M NaOH, and some pores on the surface of the sample were observed.

• Environmental Engineering Research
• /
• 제13권3호
• /
• pp.112-118
• /
• 2008

Residual solid in excess sludge treated by hydrothermal reaction was investigated as raw material for its recycling. Treated excess sludge and residual solid were also focused on their content change during hydrothermal reaction. Two kinds of excess sludge, obtained from a local food factory and a municipal wastewater treatment process, were tested under various conditions. Following hydrothermal reaction, depending on the reaction conditions, biodegradable substrates in treated excess sludge appeared to increase. The separated residual solid was a composite composed of organic and inorganic materials. The proportion of carbon varied from 34.0 to 41.6% depending on reaction conditions. Although 1.89% of hazardous materials were detected, SiO2 (Quartz) was a predominant constituent of the residual solid. X-ray diffraction (XRD) experiments revealed that the residual solid was of a partially amorphous state, suggesting that the residual solids could be easily converted to stable and non harmful substances through a stabilization process. Thus, this technology could be successfully used to control excess sludge and its reuse.

• 한국수처리학회지
• /
• 제26권6호
• /
• pp.73-80
• /
• 2018

In this study, the solids removal characteristics using T-P sludge generated from PACl coagulation were analyzed by laboratory scale and full scale experiment. As the amounts of T-P sludge injection into the raw sewage influent increased at the rate of 0, 1, 2, 3, 4 %, the suspended solids concentrations after 20 minutes setting test decreased to 210, 137, 91, 64, 43 mg/L, respectively. The filtration time required for dewatering test of the raw sewage influent decreased to 982, 728, 658, 581, 492 sec for 0, 1, 2, 3, 4% of T-P sludge injection, respectively. As the amounts of PACl coagulant into the effluent from final setting tank increased at 0, 10, 20, 30, 40 mg/L, the required filtration times for T-P sludge increased into 12.3, 41.7, 53.7, 67.2, 79.5 sec and the dewaterability of T-P sludge decreased. After T-P sludge returned into the primary settling tank on J-si sewage treatment plants, the effluent concentrations of COD, SS, T-N and T-P from primary settling tank into bioreactor decreased by 35.9, 27.9, 22.2, and 52.6% due to the coagulation effects of the T-P sludge. Finally, it was found that the return of T-P sludge into the primary settling tank could result into the sludge reduction having a lower water content of 3.03% p than in case of the only T-P sludge dehydration.

• 자원리싸이클링
• /
• 제21권5호
• /
• pp.31-37
• /
• 2012

실리콘 웨이퍼공정에서 발생하는 실리콘 슬러지로부터 실리콘 및 탄화규소를 분리한 다음, 전해법으로 원소형태의 실리콘을 회수하는 연구를 수행하였다. 실리콘 슬러지의 주요 불순물은 절삭유, 금속불순물, 실리콘 및 실리콘 카바이드를 들 수 있다. 기계적 선별법으로 분리한 실리콘, 탄화실리콘 복합물을 $1000^{\circ}C$에 1시간동안 염화 배소하여 응축하고 회수한 사염화실리콘을 이온성액체인 $[Bmpy]Tf_2N$에 용해하여 전해액으로 사용하였다. 순환전위법으로부터 $[Bmpy]Tf_2N$의 안정한 전압구간과 사염화실리콘을 용해한 $[Bmpy]Tf_2N$ 전해액에서 실리콘의 환원으로 추정되는 환원피크를 얻을 수 있었다. 정전위법(-1.9 V vs. Pt-QRE)에서 1시간동안 금 전극 상에 전해한 다음, 전극표면을 XRD, SEM-EDS 및 XPS 분석을 통하여 실리콘이 원소형태로 전착되었음을 확인하였으며, 미량의 산소가 검출되는 것은 분석과정에서 시편이 공기 중에 노출되었기 때문으로 판단된다.