• Journal of Magnetics
• /
• v.16 no.4
• /
• pp.431-434
• /
• 2011

The reduction of the Nb content in the $(Fe_{0.75}B_{0.20}Si_{0.05})_{96}Nb_4$ bulk metallic glass (BMG) has been studied. The glass-forming ability (GFA) is reduced by decreasing the Nb content, but it can be enhanced by replacing partially Fe by Co. Furthermore, the saturation magnetization of the $(Fe_{0.8}Co_{0.2})_{76}B_{18}Si_3Nb_3$ BMG is 1.35 T, being with 13% larger than that of the base alloy $(Fe_{0.75}B_{0.20}Si_{0.05})_{96}Nb_4$. $(Fe_{0.8}Co_{0.2})_{76}B_{18}Si_3Nb_3$ BMG exhibits slightly larger $B_{800}$ (the magnetic flux density at 800 A/m) and smaller core losses (20%-30%) compared with the commercial Fe-6.5 mass% Si steel.

• Journal of the Korean institute of surface engineering
• /
• v.24 no.4
• /
• pp.179-186
• /
• 1991

The effects of silicone contents and flow rates(agitation rates) of electrolyte on the formation and mechanical properties of hard anodized film of Al-Si alloy have been studied in 12% H2SO4 + 1% Oxalic acid with varying the silicone contents in the rance of 0 to 11.6% and the flow rates of electrolyte in the range of 0 to 90cm/sec. The film forming voltage required to maintain an equivalent current density significantly increase with the silicone content of Al-Si alloys due to a low conductivity of silicone. Hardness and wear resistance of the anodized film of Al-Si alloys decreases wit increasing the silicone content. The increase in the flow rate of electrolyte has a similar influence on the formation and mechanical properties of anodized film as does the decrease in bath temperature. Hardness of anodized film is rapidly increased with the flow rate being increased from 10cm/sec. It is observed that the increase in the flow rate from 11cm/sec. It is observed that the increase in the flow from 11cm/sec to 48cm/sec is more effective in enhancing the hardness of film than is the decrease in bath temperature from 1$0^{\circ}C$ to $0^{\circ}C$.

• Journal of Korea Foundry Society
• /
• v.27 no.5
• /
• pp.221-223
• /
• 2007

공구강은 C, Cr, V, Mo, W, Co 및 Si 과 같은 첨가원소를 함유한 복잡한 철계 합금으로 주요 특성인 경도, 부식저항성, 열 연화저항성 그리고 인성의 요구수준에 따라 화학성분이 결정된다. 본 연구에서는 1.0C, 0.2Mn, 3.8Cr, 1.5W, 8.5Co, 9.2Mo, 1.0V 조성의 M42 공구강의 미세조직과 열간가공성에 미치는 Si 함량의 효과를 체계적으로 조사하였다. 진공유도용해를 이용하여 Si 함량을 중량비로 0.33 에서 1.7% 까지 변화시켜 $140{\times}140{\times}330\;mm^{3}$ 크기의 잉곳으로 제조하였다. 이렇게 제조한 잉곳들은 $1150^{\circ}C$에서 1.5시간 동안 용체화처리한 후 노냉하였고, 이어 $1180^{\circ}C$에서 15mm 두께의 판재로 열간압연하였다. 공정 탄화물의 형상 및 분해 거동을 중심으로 미세조직을 관찰한 결과 Si 함량이 증가함에 따라 분해속도가 느려지는 것을 알 수 있었고 이로 인해 열간성형성이 급격히 저하되는 것으로 나타났다.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1993.11a
• /
• pp.54-54
• /
• 1993

• Bulletin of the Korean Chemical Society
• /
• v.28 no.9
• /
• pp.1588-1590
• /
• 2007

• Bulletin of the Korean Chemical Society
• /
• v.30 no.2
• /
• pp.467-470
• /
• 2009

• Proceedings of the Korean Radioactive Waste Society Conference
• /
• 2017.10a
• /
• pp.221-222
• /
• 2017

• Applied Chemistry for Engineering
• /
• v.29 no.1
• /
• pp.112-116
• /
• 2018

In this study, the mixing characteristics of water glass and additives (Si, alkali metal), which are one of the main raw materials of silicate based binder used in the production of molds during casting process, were examined. Molecular structures of water glass, additives and mixtures were analyzed FT-IR and viscosity measurements and their correlation were compared. The addition of Si source to the water glass accelerated the Si networking in the material and increased the viscosity. When the alkali metal was added, the viscosity of the water glass decreased by suppressing the Si networking of the water glass. Viscosities of the water glass and lithium silicate (LS) mixtures increased when the content of LS was less than 20 wt% and gradually decreased when the content was more than 20 wt%. By adding KOH to the water glass, the viscosity could be lowered and it could be used effectively to mix with colloidal silica (CS) or potassium methyl siliconate (PMS).

• Journal of the Korean Ceramic Society
• /
• v.36 no.8
• /
• pp.799-804
• /
• 1999

Composites of SiC-Si3N4 consisted of uniformly distributed elongated $\beta$-Si3N4 grains and equiaxed $\beta$-SiC grains were fabricated with $\beta$-SiC,. $\alpha$-Si3N4 Al2O3 and Y2O3 powders. By hot-pressing and subsequent annelaing elongated $\beta$-Si3N4 grains were grown via$\alpha$longrightarrow$\beta$ phase transformation and equiaxed $\beta$-Si3N4 composites increased with increasing the Si3N4 content owing to the reduced defect size and enhanced crack deflection by elongated $\beta$-Si3N4 grains and the grain boundary strengthening by nitrogen incorporation. Typical flexural strength and fracture toughness of SiC-40 wt% Si3N4 composites were 783 MPa and 4.2 MPa.m1/2 respectively.

• Korean Journal of Materials Research
• /
• v.18 no.10
• /
• pp.521-528
• /
• 2008

We present the structural, optical, and electrical properties of amorphous silicon suboxide (a-$SiO_x$) films grown on indium tin oxide glass substrates with a radio frequency magnetron technique from a polycrystalline silicon oxide target using ambient Ar. For different substrate-target distances (d = 8 cm and 10 cm), the deposition temperature effects were systematically studied. For d = 8cm, oxygen content in a-$SiO_x$ decreased with dissociation of oxygen onto the silicon oxide matrix; temperature increased due to enlargement of kinetic energy. For d = 10 cm, however, the oxygen content had a minimum between $150^{\circ}\;and\;200^{\circ}$. Using simple optical measurements, we can predict a preferred orientation of liquid crystal molecules on a-$SiO_x$ thin film. At higher oxygen content (x > 1.6), liquid crystal molecules on an inorganic liquid crystal alignment layer of a-$SiO_x$ showed homogeneous alignment; however, in the lower case (x < 1.6), liquid crystals showed homeotropic alignment.