• Proceedings of the Korean Powder Metallurgy Institute Conference
• /
• 2006.09a
• /
• pp.75-76
• /
• 2006

New PM route via bulk mechanical alloying is developed to fabricate the solid solution semi-conductive materials with $Mg_2Si_{1-x}Ge_x$ and $Mg_2Si_{1-y}Sn_y$ for 0 < x, y < 1 and to investigate their thermoelectric materials. Since $Mg_2Si$ is n-type and both $Mg_2Ge$ and $Mg_2Sn$ are p-type, pn-transition takes place at the specified range of germanium content, x, and tin content, y. Through optimization of chemical composition, solid-solution type thermoelectric semi-conductive materials are designed both for n-and p-type materials.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2004.08a
• /
• pp.277-284
• /
• 2004

Low carbon steels containing Si of up to $1.2\;wt\%$ were oxidized in air at 1373 K and 1523 K, i.e. below and above the eutectic temperature of FeO and $Fe_2SiO_4$. The influence of a impurity element, S on behavior of scale formation during oxidation was investigated by using $M\"{o}chssbauer$ spectroscopy and EDS. This allowed establishment of an interface oxidation model of Si-added steel depending on temperature and an impurity element. A compound of FeO and FeS was formed in the scale/matrix interface of low carbon steels containing S of up to $0.03\;wt\%$ oxidized above 1213 K of the eutectic temperature. This was flat formed between $Fe_2SiO_4$ nodules along the scale/matrix interface without selective oxidation. It is due to low viscosity and high wettability of the compound of FeO and FeS in liquid. Conventional metallographic examinations revealed that roughness of the scale/matrix interface in Si-added steels became flat as the content of S increased. It was independent of oxidizing temperature and Si content. Effects of oxidizing temperature and an impurity element content on descaling characteristics in Si-added steels were evaluated by using a hydraulic descaling simulator. Good descaling characteristics was attributable to this flatness of the scale/matrix interface.

• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.546-552
• /
• 2010

The achievement of high gas permeability is a key factor in the development of porous SiC ceramics for applications of hot gas filter, vacuum chuck, and air spindle. However, few reports on the gas permeability of porous SiC ceramics can be found in the literature. In this paper, porous SiC ceramics were fabricated at temperatures ranging from $1600^{\circ}C$ to $1800^{\circ}C$ using the mixing powders of SiC, silicon, carbon and boron as starting materials. In some samples, expanded hollow microspheres as a pore former were used to make a cellular pore structure. It was possible to produce Si bonded SiC ceramics with porosities ranging from 42% to 55%. The maximum bending strength was 58MPa for the carbon content of 0.2 wt% and sintering temperature of $1700^{\circ}C$. The increase of air permeability was accelerated by addition of hollow microsphere as a pore former.

• Journal of the Korean Ceramic Society
• /
• v.49 no.6
• /
• pp.625-630
• /
• 2012

Highly porous silicon carbide (SiC) ceramics were fabricated from polysiloxane, SiC and carbon black fillers, AlN-$Y_2O_3$ additives, and poly (ether-co-octene) (PEOc) and expandable microsphere templates. Powder mixtures with a fixed PEOc content (30 wt%) and varying SiC filler contents from 0-21 wt% were compression-molded. During the pyrolysis process, the polysiloxane was converted to SiOC, the PEOc generated a considerable degree of interconnected porosity, and the expandable microspheres generated fine cells. The polysiloxane-derived SiOC and carbon black reacted and synthesized nano-sized SiC with a carbothermal reduction during a heat-treatment. Subsequent sintering of the compacts in a nitrogen atmosphere produced highly porous SiC ceramics with porosities ranging from 78 % to 82 % and a flexura lstrength of up to ~7 MPa.

• Korean Journal of Materials Research
• /
• v.11 no.7
• /
• pp.580-584
• /
• 2001

We have investigated the deposition characteristics of Ti-Si-N films obtained by rf magnetron sputtering with ratios of Ti/Si targets in an $Ar/N_2$ gas mixture. The growth rate and stoichiometry dependence of the Ti-Si-N films on the ratio of Ti/Si and $N_2$ flow rate ratio were found to be due to the different nitriding rate of Ti and Si targets. Additionally, their different sputtering yield of nitrified Ti and Si make a reason as well. Lowering Si content in the film favored the formation of crystalline TiN, leading to the low resistivity. Increasing N content led to the Ti-Si-N films having a higher density and compressive stress, suggesting that the N content in the film is one of the most important factors determining the diffusion barrier characteristics. In the current work, the optimum process conditions for the formation of efficient diffusion barrier of Ti-Si-N film has successfully obtained by manipulating the Ti/Si ratio of target and $N_2$ flow rate ratio.

• Transactions of Materials Processing
• /
• v.13 no.7
• /
• pp.608-613
• /
• 2004

Mechanical properties of hypereutectic Al-Si alloy are influenced by the size and distribution of primary Si. To investigate the effects of P addition and holding time, hypereutectic Al-Si alloys with various amount of P content were produced in the lab. Then, the size and distribution of primary Si were examined respectively. Mechanical properties of hardness, tensile strength and wear resistance were analyzed in conjunction with the microstructural variations in alloys.

• Proceedings of the Materials Research Society of Korea Conference
• /
• 1999.05a
• /
• pp.20-20
• /
• 1999

• Korean Journal of Materials Research
• /
• v.8 no.6
• /
• pp.513-519
• /
• 1998

Zr-Si binary alloys containing 0.01 to O.lwt.%Si were prepared to investigate the effect of Si on the corrosion behavior of Zr. Corrosion test was performed in pure water at 36$0^{\circ}C$ under a pressure of 2660psi for 100days. The alloys containing 0.01 wt. % and 0.05wt. %Si had the black and uniform oxide film and didn't show the transition of corrosion rate. However. the alloys containing O.lwt.%Si had white oxide film and showed the trasition of corrosion rate at 70 days corrosion test. The weight gain increased with the increasing Si content from 0.01 to 0.1 wt.%. The variation of Si contents had no effect on changing the oxide structure but had significant effect on the electrical resistivity of oxide. The electrical resistivity decreased with increasing Si content. The fraction of precipitates in the Zr-Si binary alloys. identified as tetragonal $Zr_{3}$Si increased with increasing Si content. The increase of the volume fraction of precipitates is thought to be responsible for the increase of weight gain due to short circuit effect of precipitate.

• Journal of Korean Society of Water and Wastewater
• /
• v.22 no.5
• /
• pp.561-569
• /
• 2008

We analyzed contents of cations and anions for the domestic bottled drinking water. Results showed that total cation content was 45.81 mg/L and contained 40% of Ca. The content of cations were decreased in the order of Ca>Si>Na>Mg>K. Total anion content was 12.20 mg/L and contained 90% of ${SO_4}^{2-}$ and $Cl^-$. $F^-$ and $NO_{3-}N$ were a little contained. While Si content was reduced 2.3~75.7%(mean value:38.5%) after freezing, Ca content was reduced 45.2% after boiling. It showed that water containing higher Ca content was significantly decreased after boiling. Precipitates formed by freezing and boiling is composed of minerals such as Si and Ca. Compared to minerals from food intake, concentrations of minerals from water intake are expected to be less influenced. It is recommended Bottled Water that contains more than 20 mg/L of Ca(exceeding water-quality standard for turbidity) is safe to drink without thawing and boiling.

• Journal of Powder Materials
• /
• v.4 no.4
• /
• pp.283-290
• /
• 1997

$Ti_5Si_3$ intermetallics containing 0-6 wt% of Cu were made by reactive sintering (RS) under vacuum using elemental powder mixtures (Process 1), electro-pressure sintering (EPS) using RS'ed materials (Process2), and EPS using elemental powder mixtures (Process 3). Relatively low dense titanium silicides were gained by process 1, in which porosity decreased with increasing Cu content. For example, porosity changed from 42 to 19.4% with the increase in Cu content from 0 to 6 wt%, indicating that Cu is a useful sintering aid. The titanium silicides fabricated by Process 2 had a higher density than those by Process 1 at given composition, and porosity decreased with increasing Cu content. For example, porosity decreased from 38 to 6.8% with the change in Cu content from 0 to 6 wt%. A high dense titanium silicides were obtained by Process 3. In this Process, porosity decreased a little by Cu addition, and was almost insensitive to Cu content. Namely, about 9 or 7% of porosity was shown in 0 or 1-6 wt% Cu containing silicides, respectively. The hardeness increased by Cu addition, and was not changed markedly with Cu content for the silicides fabricated by Process 3. This tendency was considered to be resulted from porosity, hardening of grain interior by Cu addition, and softening of grain boundary by Cu-base segregates. All these results suggested that EPS using elemental powder mixtures (Process 3) is an effective processing method to achieve satisfactorily dense titanium silicides.