• Journal of the Korean Ceramic Society
• /
• v.47 no.6
• /
• pp.479-484
• /
• 2010

Microstructural and mechanical properties of the TiN films deposited on Si substrates under various substrate bias voltages by a reactive magnetron sputtering have been studied. It was found that the crystallographic texture, microstructural morphology and mechanical property of the TiN films were strongly depended on the substrate bias voltage. TiN films deposited without bias exhibited a mixed (200)-(111) texture with a strong (200) texture, which subsequently changed to a strong (111) texture with increasing bias voltage. It is also observed that the crystallite size decreases with increasing bias voltage, which corresponds to the increasing diffraction peak width of XRD patterns. The average surface roughness was calculated from AFM images of the films; these results indicated that the average surface roughness was increased with an increase in the bias voltage of the coatings.

• Journal of Sensor Science and Technology
• /
• v.7 no.5
• /
• pp.372-376
• /
• 1998

We developed a pulsed laser deposition(PLD) apparatus for depositing various thin films. In this study, the formation of $NbS_2$ thin film was performed in the vacuum chamber by PLD method. $Al_2O_3$(012) and Si(111) were used as the substrates. In order to investigate the growth conditions of a high crystalline $NbS_2$ thin film, the S/Nb composition ratio was varied from 2.0 to 5.25 and the substrate temperature was varied from the room temperature to $600^{\circ}C$. From the result of X-ray diffraction studies of the prepared $NbS_2$ thin films, it was reported that the $NbS_2$, thin film showed a good crystallinity at substrate temperature $600^{\circ}C$ and with S/Nb composition ratio 4.0 on $Al_2O_3$(012) but did not on Si(111). The films exhibited c-axis orientation.

• Journal of the Korean Vacuum Society
• /
• v.20 no.1
• /
• pp.50-56
• /
• 2011

In this study, the effects of ZnO buffer layer thickness and annealing temperature on the heterojunction diode, ZnO/b-ZnO/p-Si(111), were reported. The effects of those on the structural and electrical properties of zinc oxide (ZnO) films on ZnO buffered p-Si (111) substrate were also studied. Structural properties of ZnO thin films were studied by X-ray diffraction and I-V characteristics were measured by a semiconductor parameter analyzer. ZnO thin films with 70 nm thick buffer layer and annealing temperature of $700^{\circ}C$ showed the best c-axis preferred orientation. The best electrical property was found at the condition of buffer layer annealing temperature of $700^{\circ}C$ and 50nm thick ZnO buffer layer (resistivity: $2.58{\times}10^{-4}[{\Omega}-cm]$, carrier concentration: $1.16{\times}1020[cm^{-3}]$). The I-V characteristics for ZnO/b-ZnO/p-Si(111) heterojunction diode were improved with increasing buffer layer thickness at buffer layer annealing temperature of $700^{\circ}C$.

• Korean Journal of Materials Research
• /
• v.4 no.6
• /
• pp.638-643
• /
• 1994

The Si(ll1) surface structures induced by deposition of Au atoms were investigated by RHEED system. When Au atoms were deposited on the Si(ll1) $7\times7$ surfade, the dependence of structures and phases on the substrate temperatures and coverages was drastic. For O.1ML to 0.4ML of coverage the $7\times7$ structure changes to $7\times7$ + $5\times2$ structure as temperature increases to $350^{\circ}C$-$750^{\circ}C$. Between 0.4M1 to 1.OML the phase changed to $5 \times 2,\alpha- \sqrt{3} \times \sqrt{3},\beta- \sqrt{3} \times \sqrt{3}$ structure according to the substrate temperature and coverages. When the coverages exceeds O.SML, the 6 x 6 structure appears at the substrate temperature range between $270^{\circ}C$-$370^{\circ}C$ and compeletely transforms to 6 x6 at 1,OML. The isothermal desorption of Au on Si(ll1) surface investigated by using AES in the $\alpha- \sqrt{3} \times \sqrt{3},5 \times 2$ structures shows that the desorption energys of $\alpha- \sqrt{3} \times \sqrt{3}$ and 5 x 2 were 79Kcal/mol and 82 Kcal/mol respectively.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.02a
• /
• pp.59-59
• /
• 2011

We will report atomically sharp epitaxial growth of $Bi_2Se_3$ three-dimensional topological insulator films on Si(111) substrate with molecular beam epitaxy (MBE). It was achieved by employing two step growth temperatures to prevent any formation of second phase, like as $SiSe_2$ clusters, between $Bi_2Se_3$ and Si substrate at the early stage of growth. The growth rate was determined completely by Bi flux and the Bi:Se flux ratio was kept ~1:15. The second-phase-free atomically sharp interface was verified by RHEED, TEM and XRD. Based on the RHEED analysis, the lattice constant of $Bi_2Se_3$ relaxed to its bulk value during the first quintuple layer implying the absence of strain from the substrate. Single-crystalline XRD peaks of $Bi_2Se_3$ were observed in films as thin as 4 QL. TEM shows full epitaxial structure of $Bi_2Se_3$ film down to the first quintuple layer without any second phases. This growth method was used to grow high quality epitaxial $Bi_2Se_3$ films from 3 QL to 3600 QL. The magneto-transport properties of these thin films show a robust 2D surface state which is thickness independent.

• Proceedings of the Korean Magnestics Society Conference
• /
• 2012.05a
• /
• pp.146-146
• /
• 2012

• Journal of the Korean Vacuum Society
• /
• v.7 no.3
• /
• pp.237-241
• /
• 1998

The growth orientation and the surface roughness of AIN/Si(111) films grown by radio frequency (RF) reactive magnetron sputtering were investigated using in-situ x-ray scattering technique and atomic force microscopy (AFM). AIN films were initially grown with the <001> preferred growth orientation under most growth conditions. As the film gets thicker, however, the growth orientation changes significantly, especially at high substrate temperature and high RF powers. We attribute the observed behavior to the competition between the surface energy that prefers the <001> growth orientation and the strain energy that randomizes the growth orientation. In addition, we investigated the evolution of the surface morphology during the growth using the x-ray reflectivity measurement.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.22 no.5
• /
• pp.419-424
• /
• 2009

ZnO films doped with different contents of indium ($0.1{\sim}10$ at.%) were deposited on Si (111) substrate by Pulsed Laser Deposition (PLD). The structural, electrical and optical properties of the films were investigated using XRD, AFM, Hall and PL measurement. Results showed that un-doped ZnO film had (002) plane as the c-axis orientated growth, whereas indium doped ZnO films exhibited the peak of (002) and the weak (101) plane. In addition, in the indium doped ZnO films, the electron concentration is ten times higher than that of un-doped ZnO film, while the resistivity is ten times lower than that of un-doped ZnO film. The indium doped ZnO films have UV emission about 380 nm and show a red shift with increasing contents of indium. The I-V curve of the fabricated diode show the typical diode characteristics and have the turn on voltage of about 2 V.

• Journal of IKEEE
• /
• v.26 no.1
• /
• pp.111-118
• /
• 2022

In this paper, we studied 4H-SiC CMOS that can be integrated with high-voltage SiC power devices. After designing the CMOS on a 4H-SiC substrate, we compared the electrical characteristics with the reliability of high temperature operation by TCAD simulation. In particular, it was confirmed that changing HfO₂ as the gate dielectric for reliable operation at high temperatures improves the thermal properties compared to SiO₂. By researching SiC CMOS devices, we can integrate high-power SiC power devices with SiC CMOS for excellent performance in terms of efficiency and cost of high-power systems.

• Journal of the Korean Ceramic Society
• /
• v.37 no.7
• /
• pp.665-672
• /
• 2000

The ferroelectric YMnO3 thin films were prepared by MOD(metal-organic decomposition) method with Y- and Mn-acetylacetonate as starting materials. Thin films were grown on various substrates by spin-coating technique. The crystalline phases of the thin films were identified by X-ray diffractometer as a function of heat-treatment temperature, pH of coating solution and substrate. In addition, the effect of Mn/Y molar ratio(0.8~1.2) on the formation of hexagonal-YMnO3 phase was investigated. In forming highly c-axisoriented hexagonal-YMnO3 single phase, the Pt coated Si substrate was more effective than the bare Si substrate, and the optimum heat-treatment condition was at 82$0^{\circ}C$ for 30 min. Higher Mn/Y molar ratio within 0.8~1.2 and pH of YMnO3 precursor solution within 0.5~2.5 favored formation of ferroelectric hexagonal phase rather than orthorhombic phase. Leakage current density of the hexagonal-YMnO3 thin film formed on Pt(111)/TiO2/SiO2/Si substrate was low enough as 0.4~4.0$\times$10-8(A/$\textrm{cm}^2$) at 5 V and its remanent polarization(Pr), calculated from the P-E hysteresis loop, was 3 nC/$\textrm{cm}^2$.