• 한국표면공학회지
• /
• 제46권1호
• /
• pp.36-41
• /
• 2013

Friction stir welding (FSW) is a relatively new joining technique particularly for magnesium and aluminum alloys that are difficult to fusion weld. In this study, AZ31 Mg alloys were joined by FSW with shoulder diameter 11, 19 mm and rotating speed 900, 1200, 1500, 1800 rpm. The shoulder diameter and welding speed depended on the heat input during FSW process. As a result, the microstructures of stir zone were a fine grain by dynamic recrystallization. According to the larger shoulder diameter and the higher rotating speed, refined grain sizes of stir zone were grown by higher heat input, and the microhardness of stir zone was lower. The tensile strength at the shoulder diameter 19 mm, rotating speed 900 rpm was obtained maximum value. This value compared with the base metal was over 93%.

• 대한견주관절학회:학술대회논문집
• /
• 대한견주관절학회 2009년도 제17차 학술대회
• /
• pp.204-204
• /
• 2009

• 한국기계가공학회지
• /
• 제11권6호
• /
• pp.16-21
• /
• 2012

Magnesium alloy has been focussed as lightweight material owing to its high strength even though low density with aluminum alloy, titanium alloy and plastic material. Friction stir welding technique was performed by rotating and plunging a shouldered tool with a small diameter pin into the joint line between two butted plates and useful to join magnesium alloy. In this paper, the experiments of friction stir welding were done to investigate the joint characteristics of AZ31 magnesium alloy. For its evaluation, the orthogonal array method$(L_{27}(3^{13}))$ was applied with four factors of pin diameter, shoulder diameter, travel speed and rotation speed of tool and also three levels of each factor. Nine tools were worked through shoulder diameter of 9, 12, 15mm and pin root diameter of 3, 4, 5mm. In addition tensile tests were excuted for the assessment of mechanical properties for joint conditions. From the results, pin diameter, shoulder diameter, and rotating speed of tool influenced on the tensile strength meaningful, but welding speed did not influence on that by the variance analysis. Beside of that, optimum condition of tensile strength was estimated as following ; shoulder diameter:15mm, welding speed:200mm/min, rotating speed:200rpm.

• 한국기계가공학회지
• /
• 제14권5호
• /
• pp.81-87
• /
• 2015

In this paper, the finite element method was used for the flow and strength analysis of aluminum alloy under friction stir welding. The simulations were carried out using Sysweld s/w, and the modeling of the sheet was executed using Unigraphics NX6 s/w. The welding variables for the analysis were the shoulder diameter, rotating speed, and welding speed of the tool. Additionally, a three-way factorial design method was applied to confirm the effect of the welding variables on the flow and strength analysis with variance analysis. From these results, the rotating speed had the greatest influence on the maximum temperature, and the maximum temperature was $578.84{\pm}12.72$ at a confidence interval of 99%. The greater the rotating speed and shoulder diameter, the greater the difference between maximum and minimum temperature. Furthermore, the shoulder diameter had the largest influence on von Mises stress, and the von Mises stress was $184.54{\pm}12.62$ at a confidence interval of 99%. In addition to the increased shoulder diameter, welding speed, and rotating speed of the tool increased the von Mises stress.

• Clinics in Shoulder and Elbow
• /
• 제8권2호
• /
• pp.131-134
• /
• 2005

Distal clavicle tunnel widening was observed in coracoclavicular ligament reconstruction with semitendinous tendon autografts in a patient with acromioclavicular joint injury. Acromioclavicular joint separation, in a 44 years-old man was treated by coracoclavicular ligament reconstruction. We have performed x-ray evaluation on 2years 10months after surgery. The immediate postoperative tunnel size was measured 4.5mm in diameter. At postoperative 2years 10month the tunnel diameter was from 9.3 to 11.4mm. But the weightbearing clavicle view showed no significant acromioclavicular joint separation. Moreover the patient complained only minor intermittent shoulder discomfort.

• 동력기계공학회지
• /
• 제21권5호
• /
• pp.86-91
• /
• 2017

Friction Stir Welding (FSW) is useful technique to join aluminum alloy with energy efficient and environment friendly. In this paper, the design of experiment with three-way factorial design was adopted for optimum conditions of welding variables in the FSW of Al 6061 alloy. Tools of shoulder diameter of 9, 12, 15 mm and pin length of 1.5 mm were used. Also the material's dimension for welding were $2{\times}100{\times}150mm$, and the tensile specimens were worked by water-jet technique. Welding variables were shoulder diameter, rotating speed and travel speed of tool. From the results of this work, the welding factor influenced on yield strength most was travel speed and the optimum condition for FSW was predicted as the shoulder diameter of 15 mm, welding speed of 500 mm/min and rotating speed of 2,000 rpm. Also the presumption range of yield strength at optimal condition of reliability 99% was estimated to $207.19{\pm}9.91MPa$.

• 동력기계공학회지
• /
• 제19권4호
• /
• pp.11-16
• /
• 2015

Welding is very popular method for joining two or more metals. In this paper, the three-way factorial design was adopted for obtaining the optimum friction stir welding conditions of Al 5052 alloy. Tools of shoulder diameter of 9, 12, 15 mm and pin length of 1.5 mm were used. Also the material's dimension for welding was $100{\times}100{\times}2mm$, and the tensile specimens were worked by water-jet technique. Welding variables were shoulder diameter, rotating speed of tool and welding speed. As far as this work is concerned, optimum condition for friction stir joint of Al 5052 alloy was predicted as the shoulder diameter of 15 mm, welding speed of 500mm/min and rotating speed of 1000 rpm. In addition, the presumed range of tensile strength under the optimal conditions is estimated to be $208.3{\pm}5.7$ MPa with 99% reliability.

• Anatomy and Cell Biology
• /
• 제56권4호
• /
• pp.482-493
• /
• 2023

Understanding the anatomy of suprascapular area helps the clinicians and surgeons in management of any disability at the shoulder region. This work aimed to clear the different morphological and morphometrical types of suprascapular notch (SSN). Unknown 120 dry human scapulae of both sides and 60 formalin-embalmed cadaveric upper limbs (40 males and 20 females) were used in the present study. Three main morphological forms of SSN were reported: J, U, and V-shaped. J-shaped notch showed the highest incidence followed by U-shaped then V-shaped one. Morphometrically, type (III) notch was the most prevalent in both dry bones and cadavers, while the incidence of type (II) was the lowest form. Also, the measurements of superior transverse diameter, middle transverse diameter and vertical dimension of the different types of the notch showed no side or sex significant difference. The suprascapular foramen with ossified superior transverse scapular ligament (STSL) was seen in 5.8% of dry bones and 10% of cadaveric specimens. Fan and band-shaped ossified transverse scapular ligaments were reported. Absence of SSN was seen in 10.8% of dry bones, 7.5% of male and 10% of female specimens with left side predominance. V-shaped, absence, and ossified STSL were considered as predisposing factors of suprascapular nerve entrapment syndrome. Knowledge of the morphology and morphometric parameters of SSN is of great clinical significance for anatomists, radiologists, physiotherapists, orthopedics and neurosurgeons to perform good diagnosis and best planning for surgical or arthroscopic interventions within the shoulder region.

• 한국산학기술학회논문지
• /
• 제19권3호
• /
• pp.614-618
• /
• 2018

Al 6061-T6를 사용하여 마찰교반 용접 시 회전 툴 숄더의 너비부의 넓이와 회전 속도, 이동속도의 변화에 따른 물성의 변화에 대하여 평가되었다. FSW 공정의 접합 변수에 따라 인장시험을 수행하기 위하여 KS B 0801 5호에 따라 시험편을 제작하여 마찰교반 용접을 시행하였다. 마찰교반 용접이 된 시험편의 기계적 특성을 평가하기 위해 Instron 인장시험기를 사용하여 1mm/min의 시험 속도로 인장시험을 시행했다. 평가결과, 인장강도는 회전 속도가 증가함에 증가 하였다. 툴 숄더의 이동 속도가 빠를수록 툴 유형에 관계없이 인장강도는 감소하였다. 툴 숄더 직경 12 mm (TSD12) 의 인장 강도 값은 일반적으로 8mm 보다 높게 나타났다. 이동 속도와 회전하는 속도가 한계 값을 초과하면 재료의 특성에 영향을 주지 않고 안정화 단계에 도달한다. 툴 숄더 직경 8mm (TSD8) 는 TSD12 유형의 공구와 비교하여 재료 특성이 감소하고 용접 영역에서 재료가 완전히 혼합되지 않는다. 인장 강도 값은 모든 회전 속도 1500 rpm에서 상대적으로 감소한다. 이동 속도가 낮을수록 같은 회전수에서 재료의 혼합될 수 있는 양이 많으므로 인장강도값이 높게 나타난다. 결과적으로 용접 영역에서 재료를 완전히 혼합하고 전이 온도에 도달하기 위해서는 임계값을 초과하는 회전 속도가 필요하다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 추계학술대회논문집A
• /
• pp.471-476
• /
• 2001

The main object of this study is to develop a reliable FEM simulation technique for stability test using ABAQUS software and to clarify the effect of base profile of a steel D&I(drawn and ironed) can on the dome reversal pressure. For the can after body making simulation, two kind of stability test, dome buckle test and axial crush test are performed. The factors studied in the base profile on the dome reversal pressure are the base diameter, the rim radius, the dome shoulder radius, the dome radius and the dome depth. Within the limits before the occurrence of normal snap-through buckling of dome, the dome reversal pressure is improved by decreasing the base diameter, increasing the dome depth or increasing the dome shoulder depth.